2012 new wood pizza oven 1:cooking area :0.48cbm 2:heating time :10mins 3:depth : 88cm width :99cm 4:pizza capacity : 4pieces 5: weight :140kgs 6: material : stainless steel. Weight :140kgs
1.Products including: straight radiant tubes, w-type tubes, u-type tubes, electric radiant tubes. 2.Application: the various radiant tubes are used in the furnaces for steel mills, like cal(continuous annealing line), Cgl(continuous galvanizing line). 3.Material: High nickle and high chrome heat resistant alloy. We can cast standard alloy like astm, din, bs etc. 37/18nicr, 37/18 hu alloy, 48/26 22h alloy, 38/18nicr(1.4865), 24/24nbtizr, 50cr/50ni(2.4813), 1.4410, 1.4059, 1.4841, 1.4845, 1.4848, 1.4825, 1.4852, 2.4879 or as per customer's requirements 4.Quality control: We carry out very strict quality control from raw material to each step of the process, until the finished product is dispatched. To make sure the highest quality possible, each test is carried out strictly with our in-house testing facilities. The most generally used methods of testing given below: Chemical analysis by spectrometer Mechanical tests in normal and high temperature. Ultrasonic, x-ray, dye penetrant test. Boroscope; eddy current testing; microscope ; pressure tests. Straight radiant tubes, w-type tubes, u-type tubes, electric radiant tubes.
Lucy.Li at jsmsinudstry dot com 1.Products including: furance rolls. The od from min.50mm to max.1600mm. The shells are produced by centrifugal castings. 2.Application: the various furnace rollers are used in the furnaces for steel mills, like cal(continuous annealing line), Cgl(continuous galvanizing line).It is characteristic of heat resistant, corrosion resistant and wear resistant, 3.Material for centrifugal barrels: 24/24nbtz, g18/8nicr, 28cr/48ni/5w, 25cr/20ni, 24/24nicrnb(1.4855), 25cr/35ni(1.4852), 38ni/18cr(1.4865), 2.4633, 2.4879 or at customers request. Forged shafts: 310 stainless steel, en8, en24 etc. 4.Welding consumables: aws a5.11 nicrfe-3 2.4807 or 182ks or as per the buyer's requirements 5.Working temperature: depending on the materials(average: 800-1200¡æ) 4.Quality control: We carry out very strict quality control from raw material to each step of the process, until the finished product is dispatched. To make sure the highest quality possible, each test is carried out strictly with our in-house testing facilities. The most generally used methods of testing given below: Chemical analysis by spectrometer Mechanical tests in normal and high temperature. Ultrasonic, x-ray, dye penetrant test. Boroscope; eddy current testing; microscope ; pressure tests. Furance rolls. The od from min.50mm to max.1600mm.
Aluminum dross processing machine/aluminum dross processor:aluminum dross processing machine is a machine that adpots advanced foreign technology, which is mainly used to separate the aluminum form the aluminum dross, that is to say recyle the aluminum for reusage.The aluminum dross processing machine is special designed to process the hot aluminum dross, aluminm ash, aluminum slag that generated form the aluminum melting furnaces, holding furnace etc.Our hl-900, hl-1100, hl-1300 aluminum dross processor which could process about 100kg-500 kg at a time in about 12 minutes. The aluminum recyclying rate can be at least 80%.Using metech aluminum dross processing machine, which has below advantages:1.No need for any fuel in the whole process, which is energy-saving.2.It is equipped with the dust collector, which is enviroment friendly3.The dross processor is full automatic mechanical operation, which is labor-saving.4.Short operating time (10-12 minutes) with high efficiecny recycling rate (90%). Itemmedium Machine Dimensionl2000 x w1800 x h3500mm Heatproof po1300x l890mm Discharge opening50 Air outlet 420x300 Main driving axledia of axle130 Motor11kw 111 Transmissionrate15 Small size dust collectorsizel1100w1100h3000mm Stainless steel vanejiangsheng motor 4kw
Foshan metech aluminium technology co., ltd is a professional manufacturer, exporter and supplier of the full aluminium industry equipments and machinery, such as aluminium melting furnaces, aluminium holding furnaces, continuous casting and rolling machines, coal gasifier, aluminium dross processing machines , permanent magnet stirrer ect. We could offer all kinds of melting furnaces with different capacity (from 3 ton to 100 ton), different type ( regenerative furnace, reverberatory oven, tilting or stationary) , different shape( round, rectangular or vertical), different fuel ( oil fired, gas fired, electricity power ) etc. Different application (aluminum ingot, aluminum billite, recycling aluminum, aluminum scrap , wire and cable) etc.In a world, we could degsign and make the melting furnace according to your condition and need. So please tell me your detail conditions. The raw materials, daily outptu capacity, finished products etc. Aluminum melting furnaces, tilting aluminum melting furnaces, oil fired melting furnaces, industrial furnaces, stationary furnaces, twin-chamber furnaces, vertical furnace. Wooden box in containner.
Aluminum alloy rod continuous casting and rolling line by foshan metech aluminum technology co., ltd Aluminum and alloy rod continuous casting&rolling line; aluminum alloy rod&wire, al or wire rod manufacturers The aluminum rod continuous casting and rolling line equipment is used to produce aluminum rod and al-mg-si etc. Alloy rod with a high intensity and heat resistance in diameter 9.5mm, 12mm, 15mm by means of continuous casting and rolling. The line is competitive with the relative international products. Main components of aluminum alloy ccr lines Furnace with magnetic mixer or tilting furnace, in-line degassing & filtering system with launder, refining feeding device, five- wheel casting machineand pouring ladle, roller shearer, motorized straightener, multi-frequency induction heater, cast bar feed-in device, rolling mill, alloy rod quenching system, alloy rod cooling systems, dual-position coiler, electrical control system, rolling mill lubrication system and emulsion system, etc Brief flow chart Raw material¡úmelting furnace¡úholding furnace¡úflow channel¡úcasting ladle¡úcasting machine¡úoil hydraulic shearer¡úinitiative material feeding device¡úcontinuous rolling mill¡úquenching device¡úpulling device¡úcontinuous take-up (predeformation)¡úcoiler.
Main technical characteristics furnace omega m300 Weight of the load of raw material in the melting pot, kg:Up to 90 Temperature of molten material, celsius:2100 Hypobaric pressure in the chamber, torr:6245;10197;-5 Run of the rod, mm:150 Working speed of the rod, mm/hour:0, 1-1, 2 Power consumption, Kilowatt:100 Peak- kilowatt:120 Cooling water debit, cubic meter/hour:3, 5 Inert gas debit, cubic meter/cycle:0, 3 Weight, kg2205. Wooden box
The production includes Thermex hot-water and steam boilers. These boilers are made to the highest quality standards and are robust featuring an efficiency of up to 95 %. By integrating a recuperator, the boiler efficiency is additionally enhanced. The tangential input of exhaust gases into the exhaust pipes results in vortex movements by the exhaust gases without the need to use turbulators. Consequentially, the cleaning of the boiler is considerably easier and more cost effective since the turbulators do not need to be dismantled and cleaned.
General overhaul of hot-water and steam boilers by the following manufacturers TVT-TAM-STADLER, EMO Celje, Ðuro Ðakoviè, Weiss-Toplota, Kohlbach, Loos, Viessmann, Omnical, TPK. Boiler overhauls have several advantages compared to acquiring new ones: * During the overhaul all vital components of boilers are replaced (exhaust pipes, duct walls, combustion chamber... ) making them as new from the aspect of their performance, efficiency and lifetime; * Price of the overhaul does not exceed 50 % of the purchase price of a new boiler; * The services provided carry a three-year warranty; * Boiler overhauls are performed on site which is important for boiler rooms difficult to access. This makes construction as well as installation works unnecessary, there is also no need for lifts and permit application or any other additional administrative procedure.
The procedure for manufacturing a boiler you can see on our web-side.
This machine combined the function of aluminum bar sawing bench and aluminum bar heating furnace, which can complete relevant operations concurrently. Heating type:gas burning inside there is hot air insulation material filled in the furnace wall,flame heating on the surface of the workpiece direct so that absorbing more heat. Just only need 20 mins from normal temperature to the operating temperature. Equip to independent nozzle. The material rack adopts automatic feeding and recharging mode for labors saving.
This equipment combined the functions of aluminum bar sawing bench and heating furnace, which can complete relevant operations concurrently. It's energy saving and short working time.
This equipment with special scale bench that can be adjusted as per the length of workpiece. The saw blade is movable in horizontal plane for cutting. Low noise and clean .
This equipment is mainly used to the final hardening treatment to the finished aluminum profile .There are single-door, double-door, skip manual skip maneuvering mode and so on. Heating type is oil burning, gas burning, and electric heating. It is mainly used to aluminum profile aging , as well as drying and sintering at the same max temperature is 260 degree.
2.Production Description: 1)Medium Frequency Induction Furnace for melting 2)Full digital control system with high accuracy 3) Melting steel, iron,stainless steel,copper,aluminium 4)0.15-20 tons capacity 5) Constant power output, speedy melting, good electricity saving efficiency. 3.Usage: Medium Frequency Induction Furnace Mainly used in melting steel, iron, copper, aluminum and alloy, is with high melting efficiency, good electricity saving effect, good metal component uniformity, less burning loss, speedy temperature rise, easy control of temperature, is suitable to all kinds of metal melting. 4.Characters and Advantages: 1) Constant power output, speedy melting, good electricity saving efficiency. 2) Zero-voltage sweep-frequency style start, adapts to requirement of frequently start. 3) Comprehensive protection functions, such as overcurrency protection, overvoltage protection, current-limiting protection, voltage-limiting, water-break protection, and default protection, equipment runs reliably under premise of melting speed guarantee. 4) Easy to operate, suitable for all casting process. 5. Package: Plywood cases and nude.
1.Production Name: Intermediate Frequency Induction Melting Furnace, Steel Shell 2.Production Description: 1)Steel Shell Intermediate Frequency Induction Furnace for melting 2) Steel shell hydraulic tilting 3) Melting steel, iron,stainless steel 4)0.15-12 tons capacity 3.Usage: Medium Frequency Induction Furnace Mainly used in melting steel, iron, copper, aluminum and alloy, is with high melting efficiency, good electricity saving effect, good metal component uniformity, less burning loss, speedy temperature rise, easy control of temperature, is suitable to all kinds of metal melting. 4.Characters and Advantages: 1) Constant power output, speedy melting, good electricity saving efficiency. 2) Zero-voltage sweep-frequency style start, adapts to requirement of frequently start. 3) Comprehensive protection functions, such as overcurrency protection, overvoltage protection, current-limiting protection, voltage-limiting, water-break protection, and default protection, equipment runs reliably under premise of melting speed guarantee. 4) Easy to operate, suitable for all casting process. 5. Package: Plywood cases and nude. Plywood cases and nude.
Equipment Composition: (1)Power Supply: 1) VIP Power Cabinet 2) DC Smoonthing Reactor 3) Filter Compensation Capacitor 4) Furnace Tilting Control Console (2) Furnace 1) Steel Alloy Shell 2) Induction Coil 3) Hydraulic Station 4) Water Cooled Cable 5) Crucible Module (3) Closed Water Cooling System 1) Cooling Power Supply 2) Cooling Furnace.
Equipment Composition: (1) Power Supply: 1) VIP Power Cabinet 2) DC Smoonthing Reactor 3) Filter Compensation Capacitor 4) Furnace Tilting Control Box. (2) Furnace 1) Aluminum Alloy Shell 2) Inductor 3) Reduction Gear 4) Furnace Suport Shelf 5) Water Cooled Cable 6) Crucible Module (3) Closed Water Cooling System 1) Cooling Power Supply 2) Cooling Furnace.
Product Name: Steel Shell Induction Melting Furnace Product Capacity: 250kg, 350kg,500kg, 750kg, 1000kg, 2000kg,3000kg,5000kg,10000kg,15000kg, 20000kg. Power Supply: 250kw up to 6000kw. Usage: Iron, Steel, Aluminum, Copper, and Alloy melting, heat holding. Equipment Composition: (1)Power Supply: 1) VIP Power Cabinet 2) DC Smoonthing Reactor 3) Filter Compensation Capacitor 4) Furnace Tilting Control Console (2) Furnace 1) Steel Alloy Shell 2) Induction Coil 3) Hydraulic Station 4) Water Cooled Cable 5) Crucible Module (3) Closed Water Cooling System 1) Cooling Power Supply 2) Cooling Furnace. Wood case.
The boiler is a three-pass, fire-tube steam boiler made by Finnish Ahlström Themoflow in year 1990. The boiler has max operating pressure16 bar with 205 C steam temperature and it is equipped with exhaust gas economizer for preheating incoming feed-water and modulating heavy fuel oil burner. It's has a large 15.2 m3 water volume which allows big momentary changes in load. Other benefits include simple structure, long operating life, reliability and ease of service and maintenance. The boiler is in good operational condition. Feed water pumps and feed water tank with aerator are available for separate request and price. Technical Data: Manufacturer: Ahlström Thermoflow, Kaarina Manufacturing year: 1990 Capacity: 3.3 MW Water volume: 15.2 m3 Steam characteristics: Max 16 bar, at 205 C temperature, saturated Oil Burner: Weishaupt Monarch RMS 50/2 A - ZM (YOC 1990) Oil feeding: 140 - 490 kg/h.
