Coal dryer is now hot equipment in the world. Coal is vital energy resource in various industries and daily life. When coal is washed or stored in open yard, some is washed away which forms coal slime later. This is a great loss. Coal slime is of high moisture and low heat, which means poor economic value. However, coal dryer solves this problem perfectly. Under normal conditions, moisture inside of coal slime is 20-30%. After drying, the moisture can be reduced to 0.1%. Thus, coal slime can be used in many occasions. Coal dryer turns waste into treasure. How does coal dryer work? Coal dryer is divided into several sections for higher efficiency. A. Transmission section. Wet material enters coal dryer, then it gets full contact with hot air, moisture inside gets vaporized. With lifting boards elevating and scattering materials repeatedly, wet material is conveyed to next section. B. Cleaning section. When materials fall down, they are easy to stick on the inner wall of the cylinder. During this process, cleaning device breaks the clumps. This spreads the surface area of heat exchange and improves heat efficiency. C. Lifting boards section. Wet material gets loose and of low moisture content that meets the requirement. D. Discharging section. No lifting boards in this area. Materials roll to the outlet coal dryer. The whole drying process is completed. Diameter of cylinder 1.2m Length of cylinder 10m
Sand dryer is a type of industrial dryer employed to reduce or minimize the liquid moisture content of the material it is handling by bringing it into direct contact with a heated gas. Sand dryer is made up of a large, rotating cylindrical tube, usually supported by concrete columns or steel beams. Sand dryer slopes slightly so that the discharge end is lower than the material feed end in order to convey the material through the dryer under gravity. Material to be dried enters sand dryer, and as sand dryer rotates, the material is lifted up by a series of internal fins lining the inner wall of sand dryer. When material gets high enough to roll back off the fins, it falls back down to the bottom of sand dryer, passing through the hot gas stream as it falls. This gas stream can either be moving toward the discharge end from the feed end (known as co-current flow), or toward the feed end from the discharge end (known as counter-current flow). The gas stream can be made up of a mixture of air and combustion gases from a burner, in which case sand dryer is called a direct heated dryer. Diameter of cylinder 1.0m Length of cylinder 8m
Zhengzhou kehua industrial dryer co., ltd is a professional manufacturer engaged in industrial dryer. Established in 1970s, we have accumulated rich experience in technical problems and grown to be leader in industrial dryer industry. Our industrial dryer mainly includes rotary dryer, vertical dryer, airflow dryer and belt dryer which are widely used in construction, mining, metallurgy, chemical, agriculture, forestry industry. Now our industrial dryer has been exported to america, israel, australia, india, philippines, etc. Good credit, high quality, competitive price, all these help us win praise from partners. We hope to establish long-term business relationship with friends from various countries. There is various industrial dryer in the workshop, you are welcome to visit our factory. Diameter of cylinder 1.5m Length of cylinder 12m
Technical parameters: Model (ton/furnace)Furnace hearth size (m)Energy consumption (kg/h) 30.14*1.6*2.0150 50.45*2.0*2.4200 80.49 *2.4*3.0200 100.49*2.8*4.5250 120.55*2.8*4.5250 150.55*3.0*5.0300 Technical parameters: Model (ton/furnace)Furnace hearth size (m)Energy consumption (kg/h) 30.14*1.6*2.0150 50.45*2.0*2.4200 80.49 *2.4*3.0200 100.49*2.8*4.5250 120.55*2.8*4.5250 150.55*3.0*5.0300
Type: FD-J-1-3 Input power:3-phase AC 380V Total power:26KW Max processing glass size: 2440*1830mm Arched height:400mm Glass thickness:36mm Processing cycle:40-60min/furnace Max processing area:40©O Machine dimension:3250 28501300 mm Working temperature:90-140
Made of stainless steel, Ceramic wool insulated body. With perfect design stainless steel fan, homogenic&multi dimensional heat distribution. Automatic moisturizing. Thermostatic control. Thermometer. Detachable interior glass enabling easy clean. Ergonomic and elegant shape with perfect satin-finished sheet.. Perfect design and high quality meterial to prevent permanent deformity. Appropriate for multipurpose use, optional choices: *fas102-1 oven base *fas102-2 oven base with sliding tray *fmd102 leavening chamber Water and oil proof switches. Competitive high quality and attractive price. Iso 9001:2000 Turkish standards institution (tse) Ce
We are providing services like reconditioning of: Furnace crucible Induction melting furnace coil Water cooled cable Our special services : New matching furnace assembly (100kg -10000kg) suitable with existing power supply unit. A servicing and maintenance contracts for complete power supply with furnace assembly of all leading manufacturer of induction furnace supplier. Complete project consulting for buying of new induction furnace. We under take modification and repairs for old furnaces and bar heater coil box of heating equipments
Heat soak furnace, we often call it tempering furnace. It is the necessary equipment for producing tempered glass. Why tempered glass break? Tempered glass could have spontaneous breakage without receiving any external force, which is the nature of tempered glass. The reason comes from nickel sulfide inside the glass. Nickel sulfide is ¦á¡«nis in high temperature during the heating section. When cooled rapidly, ¦á¡«nis can not change correspondingly to ¦â¡«nis of low temperature. The morphic transformation will last for ten of years which lead to spontaneous breakage. What is heat soaking? Heat soaking is a destructive process in which a pane of tempered glass is subjected to temperatures up to 280¡ã c for several hours over a specific temperature gradient to induce fracture. This test insures that if there is probability of breakage then the infected panes break inside the furnace at the factory itself. Up to 95 % nis infested panes are usually destroyed inside the heat soak chamber at the factory premises and hence reduce the chances of onsite breakages. The machine is characteristic of computer in-process monitoring and controlling, multi curve display, data storage, record check and curve printing. Extended functions like low temperature frit drying and pre-pressing of bending lamination glass. Customized machines are available.
Power:300w Temperature range:50-200¡æ Customization:Offered Material:Stainless steel Type:Steady state drying chamber Weight:30 kg Interior dimension: 250x250x250 mm Application areas:For minning, chemical, research institution and labs to pre heating, pre aging, drying or curing.
2012 new wood pizza oven 1:cooking Area :0.3cbm 2:heating time :5mins 3:depth : 73cm width :82cm 4:pizza capacity : 2pieces 5: weight :100kgs 6: material : stainless steel Weight :100kgs
2012 new wood pizza oven 1:cooking area :0.48cbm 2:heating time :10mins 3:depth : 88cm width :99cm 4:pizza capacity : 4pieces 5: weight :140kgs 6: material : stainless steel. Weight :140kgs
1.Products including: straight radiant tubes, w-type tubes, u-type tubes, electric radiant tubes. 2.Application: the various radiant tubes are used in the furnaces for steel mills, like cal(continuous annealing line), Cgl(continuous galvanizing line). 3.Material: High nickle and high chrome heat resistant alloy. We can cast standard alloy like astm, din, bs etc. 37/18nicr, 37/18 hu alloy, 48/26 22h alloy, 38/18nicr(1.4865), 24/24nbtizr, 50cr/50ni(2.4813), 1.4410, 1.4059, 1.4841, 1.4845, 1.4848, 1.4825, 1.4852, 2.4879 or as per customer's requirements 4.Quality control: We carry out very strict quality control from raw material to each step of the process, until the finished product is dispatched. To make sure the highest quality possible, each test is carried out strictly with our in-house testing facilities. The most generally used methods of testing given below: Chemical analysis by spectrometer Mechanical tests in normal and high temperature. Ultrasonic, x-ray, dye penetrant test. Boroscope; eddy current testing; microscope ; pressure tests. Straight radiant tubes, w-type tubes, u-type tubes, electric radiant tubes.
Lucy.Li at jsmsinudstry dot com 1.Products including: furance rolls. The od from min.50mm to max.1600mm. The shells are produced by centrifugal castings. 2.Application: the various furnace rollers are used in the furnaces for steel mills, like cal(continuous annealing line), Cgl(continuous galvanizing line).It is characteristic of heat resistant, corrosion resistant and wear resistant, 3.Material for centrifugal barrels: 24/24nbtz, g18/8nicr, 28cr/48ni/5w, 25cr/20ni, 24/24nicrnb(1.4855), 25cr/35ni(1.4852), 38ni/18cr(1.4865), 2.4633, 2.4879 or at customers request. Forged shafts: 310 stainless steel, en8, en24 etc. 4.Welding consumables: aws a5.11 nicrfe-3 2.4807 or 182ks or as per the buyer's requirements 5.Working temperature: depending on the materials(average: 800-1200¡æ) 4.Quality control: We carry out very strict quality control from raw material to each step of the process, until the finished product is dispatched. To make sure the highest quality possible, each test is carried out strictly with our in-house testing facilities. The most generally used methods of testing given below: Chemical analysis by spectrometer Mechanical tests in normal and high temperature. Ultrasonic, x-ray, dye penetrant test. Boroscope; eddy current testing; microscope ; pressure tests. Furance rolls. The od from min.50mm to max.1600mm.
Aluminum dross processing machine/aluminum dross processor:aluminum dross processing machine is a machine that adpots advanced foreign technology, which is mainly used to separate the aluminum form the aluminum dross, that is to say recyle the aluminum for reusage.The aluminum dross processing machine is special designed to process the hot aluminum dross, aluminm ash, aluminum slag that generated form the aluminum melting furnaces, holding furnace etc.Our hl-900, hl-1100, hl-1300 aluminum dross processor which could process about 100kg-500 kg at a time in about 12 minutes. The aluminum recyclying rate can be at least 80%.Using metech aluminum dross processing machine, which has below advantages:1.No need for any fuel in the whole process, which is energy-saving.2.It is equipped with the dust collector, which is enviroment friendly3.The dross processor is full automatic mechanical operation, which is labor-saving.4.Short operating time (10-12 minutes) with high efficiecny recycling rate (90%). Itemmedium Machine Dimensionl2000 x w1800 x h3500mm Heatproof po1300x l890mm Discharge opening50 Air outlet 420x300 Main driving axledia of axle130 Motor11kw 111 Transmissionrate15 Small size dust collectorsizel1100w1100h3000mm Stainless steel vanejiangsheng motor 4kw
Foshan metech aluminium technology co., ltd is a professional manufacturer, exporter and supplier of the full aluminium industry equipments and machinery, such as aluminium melting furnaces, aluminium holding furnaces, continuous casting and rolling machines, coal gasifier, aluminium dross processing machines , permanent magnet stirrer ect. We could offer all kinds of melting furnaces with different capacity (from 3 ton to 100 ton), different type ( regenerative furnace, reverberatory oven, tilting or stationary) , different shape( round, rectangular or vertical), different fuel ( oil fired, gas fired, electricity power ) etc. Different application (aluminum ingot, aluminum billite, recycling aluminum, aluminum scrap , wire and cable) etc.In a world, we could degsign and make the melting furnace according to your condition and need. So please tell me your detail conditions. The raw materials, daily outptu capacity, finished products etc. Aluminum melting furnaces, tilting aluminum melting furnaces, oil fired melting furnaces, industrial furnaces, stationary furnaces, twin-chamber furnaces, vertical furnace. Wooden box in containner.
Aluminum alloy rod continuous casting and rolling line by foshan metech aluminum technology co., ltd Aluminum and alloy rod continuous casting&rolling line; aluminum alloy rod&wire, al or wire rod manufacturers The aluminum rod continuous casting and rolling line equipment is used to produce aluminum rod and al-mg-si etc. Alloy rod with a high intensity and heat resistance in diameter 9.5mm, 12mm, 15mm by means of continuous casting and rolling. The line is competitive with the relative international products. Main components of aluminum alloy ccr lines Furnace with magnetic mixer or tilting furnace, in-line degassing & filtering system with launder, refining feeding device, five- wheel casting machineand pouring ladle, roller shearer, motorized straightener, multi-frequency induction heater, cast bar feed-in device, rolling mill, alloy rod quenching system, alloy rod cooling systems, dual-position coiler, electrical control system, rolling mill lubrication system and emulsion system, etc Brief flow chart Raw material¡úmelting furnace¡úholding furnace¡úflow channel¡úcasting ladle¡úcasting machine¡úoil hydraulic shearer¡úinitiative material feeding device¡úcontinuous rolling mill¡úquenching device¡úpulling device¡úcontinuous take-up (predeformation)¡úcoiler.
Main technical characteristics furnace omega m300 Weight of the load of raw material in the melting pot, kg:Up to 90 Temperature of molten material, celsius:2100 Hypobaric pressure in the chamber, torr:6245;10197;-5 Run of the rod, mm:150 Working speed of the rod, mm/hour:0, 1-1, 2 Power consumption, Kilowatt:100 Peak- kilowatt:120 Cooling water debit, cubic meter/hour:3, 5 Inert gas debit, cubic meter/cycle:0, 3 Weight, kg2205. Wooden box
The production includes Thermex hot-water and steam boilers. These boilers are made to the highest quality standards and are robust featuring an efficiency of up to 95 %. By integrating a recuperator, the boiler efficiency is additionally enhanced. The tangential input of exhaust gases into the exhaust pipes results in vortex movements by the exhaust gases without the need to use turbulators. Consequentially, the cleaning of the boiler is considerably easier and more cost effective since the turbulators do not need to be dismantled and cleaned.
General overhaul of hot-water and steam boilers by the following manufacturers TVT-TAM-STADLER, EMO Celje, Ðuro Ðakoviè, Weiss-Toplota, Kohlbach, Loos, Viessmann, Omnical, TPK. Boiler overhauls have several advantages compared to acquiring new ones: * During the overhaul all vital components of boilers are replaced (exhaust pipes, duct walls, combustion chamber... ) making them as new from the aspect of their performance, efficiency and lifetime; * Price of the overhaul does not exceed 50 % of the purchase price of a new boiler; * The services provided carry a three-year warranty; * Boiler overhauls are performed on site which is important for boiler rooms difficult to access. This makes construction as well as installation works unnecessary, there is also no need for lifts and permit application or any other additional administrative procedure.
The procedure for manufacturing a boiler you can see on our web-side.
