6.2011.1 For Kaeser Oil Separator Filter Element Replacement.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
Unatex air compressor 0220701005 0220610001 oil filter 0220101021 Air filter.The oil mist filter for vacuum pump is my company independent research and development production of high efficiency filtration product, used for oil lubricated rotary vane vacuum pump exhaust the oil and gas separation device, installed in the vent pipe of the vacuum pump, in the process of vacuum pump operation, exhaust gas go through the filter, oil mist particles in liquid form cannot directly go through glass fiber filter paper, and then attached to the filter paper, clean gas is under certain pressure go through the glass fiber paper discharge smoothly, and to reduce pollution,ensure a clean environment. Data: Brand model size of interface sucking rate Nanfeng KF25 DN25 8L/S Product features: 1, Vacuum pump oil mist filter shell adopt imported high strength transparent material production, high temperature resistance, corrosion resistance, good appearance, and can directly observe the oil and gas separation condition; 2, Long service life, effectively filtering mechanical pump vent discharge of oil mist, filtration rate above 99%, can effectively reduce the air pollution, improve the working environment; 3, Filter material adopt imported glass fiber paper, stable performance and strong oil absorption; 4, The device is designed as a quick release v band clamp flange, quick installation and easily fitting with vacuum pumps exhaust pipe of different models and import brands . Replacement steps of exhaust filter: 1.After the vacuum pump stops, ensure that the system is under pressure. 2.Remove the quick release v band clamp flange on the filter. 3.Remove the oil mist filter and replace it with a new one. Note: when replacing the oil mist filter, it is better to replace the vacuum pump oil at the same time.
Diameter: from 0.5mm to 2500mm,Surface Quality: 10-5 S/D... Material::BK7, fused silica, borofloate, CaF2, MgF2, Ge, Si, ZnSe, ZnS, SF, LaF, BaK... Coating: AR coating,Al/Au reflective coating,BBAR coating,DLC coating,Dielectric HR coating... Application: In the field of Defence,Imaging,medical,laser,sensor,Biochemical.. Features: Optical bandpass filters transmit light only within a defined spectral band ranging from less than one to many nanometers wide. Benefits: a. Long Band Pass b. Sort Band Pass c. Narrow FWHM d. High Transmission We believe that Optical bandpass filters offers an unbeatable combination of quality, performance, and value. If you have any questions about this product or would like to learn more about how it can benefit your business, please don't hesitate to contact us. We are dedicated to providing excellent customer service and helping our customers achieve their business goals. Thank you for considering Optical bandpass filters. We look forward to the opportunity to work with you and help you achieve success.
TEMPO make lab clean is a carefully enclosed machine which is a unique filter combination that filters our air and gas contaminants thus by giving most clean air. The air is drawn through the prefilter, carbo filter and HEPA filter and blown clean air in the room. Application : Drug manufacturer company Paint manufacturer company Rubber industry Food Manufacturer (sugar, spices) Polymer industry Andrology and IVF lab Chemical lab Offices ICU rooms Hospital waiting rooms Construction : Single wall construction in SS 304 or GI powder coated. Blower : Backward curved centrifugal fan Dynamically and statically balanced blower less vibration and less noise. Filter system Prefilter : Prefilter efficiency-EU-5 rating Efficiency 95% to 5 micron Carbon filter : Reduces CFU and VOC HEPA Filter Efficiency-EU-13 rating Removing ultrafine particles (dust, dander, pollen, mould ad other common allergens in the room) Efficiency 99.97% to 0.3 microns. Filter replacement : Timer for filter life Unique indicator for a filter change.
Introduction The ARLTS series filter cartridge is made of hydrophobic PTFE micropore membrane as the filtering medium. It is manufactured by thermally fusing PTFE filter membrane and PP support material, without any adhesives. Its main features include strong hydrophobic, high retention rate, excellent chemical resistance and thermal stability. It maintains effective filtration effect for corrosive solvents and strong oxidizing liquids. The double-layer membranes formula can better improve the filtration efficiency. Its biological safety and endotoxin indexes meet FDA requirements and Chinese Pharmacopoeia standards. All products have passed integrity tests of the instrument. Specification Filter material: Hydrophobic PTFE micropore filter membrane (single/double layer) Diameter: 69, 83 mm Pore size: 0.1 ~ 3 micron Length: 5" ~ 60" Interface type: 222, 226, 215, 213, DOE Gasket/O-rings: Silicone, EPDM, NBR, Viton, wrapped in PTFE Application Chemical industry: Terminal filtration for organic solvents, inorganic solvents, chemical reagents, etc. Food Industry: Terminal filtration for clarification of liquor, beverages, wines, fruit wines, removal of microorganisms and fine particles, etc. Gas Industry: Gas filtration, sterile storage tank respirator, air fermentation tanks, etc.
Introduction The ARLTQ series filter cartridge is made of hydrophilic PTFE micropore membrane as the filtering medium. It is manufactured by thermally fusing PTFE filter membrane and PP support material, without any adhesives. It is suitable for the chemical and pharmaceutical industry with strict requirements. Its main features include stable hydrophilic, high retention rate, excellent chemical resistance and thermal stability. It does not require pre-wetting when filtering solvents with high water content. The double-layer membranes formula can better improve the filtration efficiency. Its biological safety and endotoxin indexes meet FDA requirements and Chinese Pharmacopoeia standards. All products have passed integrity tests of the instrument. Specification Filter material: Hydrophilic PTFE micropore filter membrane (single/double layer) Diameter: 69, 83 mm Pore size: 0.1 ~ 3 micron Length: 5" ~ 60" Interface type: 222, 226, 215, 213, DOE Gasket/O-rings: Silicone, EPDM, NBR, Viton, wrapped in PTFE Application Pharmaceutical Industry: Sterile active pharmaceutical ingredients, sterilization filtration of pharmaceutical liquids, etc. Chemical Industry: Filtration of hydrophilic organic solvents, inorganic solvents, chemical reagents, etc. Food Industry: Filtration of alcohol, beverage, etc.
Introduction The ARLE series micropore filter cartridge is made of PES micropore membrane as the filtration medium. The uniquely shaped and evenly distributed micropores cover more than 85% of the membrane area, ensuring high filtration efficiency and stability. This product exhibits excellent hydrophilic, is free from surfactants, and features efficient antibacterial properties, low adsorption, high mechanical strength, as well as resistance to high temperatures and pressures. It can withstand multiple cycles of steam sterilization. The double-layer filter membrane formula can better improve the filtration effect. All products have passed the integrity test of the instrument. Specification Filter material: PES micropore filter membrane (single / double Layer) Diameter: 69, 83 mm Pore size: 0.1 ~ 1 micron Length: 5" ~ 60" Interface type: 222, 226, 215, 213, DOE Gasket/O-rings: Silicone, EPDM, NBR, Viton, wrapped in PTFE Application Suitable for terminal filtration in pharmaceutical, biological products, microelectronics, semiconductor, chemical and other industries.
Introduction The ARSP series micropore membrane filter cartridge is made of PP microfiber as the filtration medium. The product is formed by folding the combination of multi-layer filter membranes, achieving a stable deep filtration effect. In order to meet the market demand for high-flow filtration, the product increases the effective filtration area of the membrane. It has the characteristics of high flow rate, long service life, stable structure and wide chemical compatibility, which are conducive to enhancing the filtration efficiency of liquids. It is mainly used for liquid filtration in large-scale LCD and touch panel processes, such as substrate cleaning, stripping, etching, developer and deionized water rinsing, etc. It also meets the demand for large flow rates in the chemical and food industries. Specification Filter material: PP micropore filter membrane Diameter: 131 mm Pore size: 0.1 ~ 60 micron Length: 10" ~ 60 " Interface type: 334 Gasket/O-rings: Silicone, EPDM, NBR, Viton, wrapped in PTFE Application Electronics industry: Wet processing of LCD and touch panels, semiconductor process, wet equipment chemical reagent Chemical industry: Chemical solvents Food industry: Beverage, alcohol
Introduction The ARLP series micropore filter cartridge is made of PP microfiber as the filtration medium, and the filtration material meets the relevant FDA requirements. The product is formed by folding the combination of multi-layer filter membranes, achieving a stable deep filtration effect. Its main features include low filtration resistance, high dirt-holding capacity, long service life, stable structure, wide chemical compatibility, etc. It is suitable for pre-filtration of various liquids. Specification Filter material: PP micropore filter membrane Diameter: 69 mm Pore size: 0.1 ~ 60 micron Length: 5" ~ 60 " Interface type: 222, 226, 215, 213, DOE Gasket/O-rings: Silicone, EPDM, NBR, Viton, wrapped in PTFE Application Primary filtration of filtration systems in the pharmaceutical, chemical solvent, food and beverage, microelectronic industries, pure water systems, petrochemical and other industries.
Introduction The filtration medium of ARWP series micropore membrane filter cartridge is made of PP superfine fiber membrane. It is formed by folding the combination of multi-layer filter membranes and thermally welding into 6-inch large diameter structure, providing large filtration area for stable deep filtration effect. This product is available in both external and internal pressure types, featuring high efficiency retention and high liquid flux, widely used in security filtration and pre-filtration across various industries. Specification Filter material: PP micropore filter membrane Diameter: 6" (152mm) Pore size: 1 ~ 80 micron Length: 20", 40", 60" Interface type: Multiple interface selections Gasket/O-rings: Silicone, EPDM Application General industry: Filtration of workshop water for various production processes, etc. Electronics industry: Pre-filtration for reverse osmosis systems, pre-filtration for deionized water, etc. Power plants: Filtration of makeup water, condensate water, cooling water, wastewater treatment, etc.
Introduction The ARTX series filter cartridge uses high-quality polyacrylonitrile as the raw material, which is high-temperature carbonized into powdered fibers in a high-purity inert gas environment. Through special formulation and surface design, it enhances the ability to adsorb suspended solids and precipitated particles in liquids, achieving deep filtration effect. This product performs excellently in chlorine removal, purification and decolorization, adsorption of organic compounds and metal ion removal. Specification Filter material: Powdered activated carbon fiber Length: 5" ~ 40" Pore size: 5 ~ 100 micron (multi-micropore combination) Diameter: 65 mm Interface type: DOE Gasket/O-rings: TPE Application Chemical industry: Air purification, organic solvent decolorization Drinking water: Chlorine removal, odor removal, water purification Electronics industry: Water treatment purification, PCB electroplating, semiconductor FRAME electroplating solution, copper-nickel electroplating solution filtration, etc. Food industry: Filtration for beverages, clarification of wines, etc.
Introduction The ARTB series filter cartridge uses high-purity titanium powder as the raw material, processed through high-temperature vacuum sintering. It features high porosity, uniform pore size distribution, and unique capabilities to withstand temperatures up to 300 degrees Celsius (in wet conditions) as well as strong acids and alkalis. This product is easy to backwash, enabling effective regeneration, and is suitable for separating and purifying various gases or liquid media. Specification Filter material: High-purity titanium Pore size: 0.22 ~ 100 micron Length: 5" ~ 40" Diameter: 60 ~ 100 mm Physical regeneration methods: a. Pure water backwashing b. Steam blowback c. Ultrasonic cleaning Chemical treatment methods: a. Alkaline washing b. Acid washing Interface type: 222, 226, 215, DOE, M20, M30, M36, M42 Gasket/O-rings: Silicone, EPDM, NBR, Viton, wrapped in PTFE Application Pharmaceutical industry: Decarbonization and impurity removal filtration in the production of raw pharmaceutical materials. Chemical industry: Filtration of strong acidic and alkaline chemical solvents. Water treatment industry: Pre-filtration for reverse osmosis systems, seawater desalination, wastewater treatment systems, etc. Gas industry: Purification of compressed air and catalytic gases, filtration in ozone sterilization systems. Food industry: Clarification filtration for food and beverages, edible oils, soy sauce, vinegar, and other products.
Introduction The common materials of ARLD series filter bags include PE, PP, NMO, and PTFE. This series of products utilizes sewing or hot-melt technology, and the surface is heat-treated at high temperature to effectively prevent fiber shedding. The uniform filter layer has highly efficient filtration of solid and colloidal particles. The high-strength filament fibers enable high flow rate and strong dirt-holding capacity, ensuring stable structure. The filter bags are made of different materials with different chemical corrosion resistance and heat resistance properties, widely applied in primary liquid filtration in various industries. Specification Filter material: PE, PP, NMO, PTFE Pore size: 0.5 ~ 300 micron Filter bag size: Various specifications can be customized Collar ring material: PP, stainless steel Application Pharmaceutical industry: Filtration of various liquid medicines, traditional Chinese medicine preparations, antibiotics, injection bottle washing water Food industry: Filtration of food, beverages, alcohol, drinking water Chemical industry: Filtration of chemical solvents, paints, coatings, inks, adhesives, printing and dyeing pigments, metal cutting, etc.
Introduction The ARRP series filter cartridge uses odorless and non-toxic PP as raw material. It is formed into a tubular filter cartridge through a process involving heating, melting, spinning, pulling, and molding. This product adopts a progressive process and a design of outer sparse and inner dense, which can maintain a stable flow rate and show excellent deep filtration effect. Its main features include low resistance, high dirt holding capacity, corrosion resistance and strong chemical compatibility. Specification Filter material: PP Diameter: 61 ~ 114 mm Pore size: 1 ~ 100 micron Length: 5" ~ 60" Interface type: 222, 226, 215, DOE Gasket/O-rings: Silicone, EPDM, NBR, Viton, wrapped in PTFE Application Suitable for solution filtration of larger particles in various industries. Widely used in PCB, electroplating solution, pure water engineering, food and drinking water pre-filtration, etc.
Introduction The ARBP series micropore membrane filter cartridge is made of polypropylene microfiber as the filtration medium. The product is formed by folding the combination of multi-layer filter membranes, achieving a stable deep filtration effect. Its large diameter design increases the filtration area, effectively reducing the quantity of filter cartridges used and the frequency of replacements, thereby lowering production costs. Due to its high flow rate and large dirt-holding capacity, this product is widely used in the filtration of liquid chemicals in the manufacturing process of LCD and touch panel, such as substrate cleaning, stripping, etching and deionized water rinsing. Specification Filter material: PP micropore filter membrane Diameter: 83 mm Pore size: 0.1 ~ 60 micron Length: 10" ~ 60 " Interface type: 226 Gasket/O-rings: Silicone, EPDM, NBR, Viton, wrapped in PTFE Application Electronics industry: Wet processing of LCD and touch panels, semiconductor process, wet equipment chemical reagent Chemical industry: Chemical solvents
Introduction The ARQS series filter housing is constructed from high-strength stainless steel materials (SUS316L or SUS304), achieving a sanitary-grade finish on both inner and outer surfaces through mechanical polishing. Its design is reasonable with a well-crafted structure, ensuring cleanliness and safety of the outlet. Using single or multiple PTFE filter cartridges as filtration elements can filter out particles and bacteria more than 0.02 micron from gas. Specification Material: SUS304, SUS316L Filter type: Gas Length(matched cartridge): 5" ~ 40" Filter specification: Single core or multi-core Application Suitable for biologicals, food, microelectronics industry, chemical industry and other fields with strict gas requirements, especially the purification and filtration of medium to large storage tank intake.
Introduction The honeycomb wire wound filter cartridge mainly uses PP, degreased cotton, and glass fiber as raw materials. a.The ARXF series honeycomb filter cartridge is mainly made of a PP reinforced skeleton and PP fiber threads by winding. b.The ARXT series honeycomb filter cartridge is made of degreased cotton utilizes yarn spun from processed and degreased natural cotton, wrapped around a PP or stainless steel porous skeleton. c.The ARXB series honeycomb filter cartridge, constructed with a stainless steel porous skeleton wrapped with glass fiber threads, is resistant to strong acids and alkalis, capable of withstanding temperatures up to 200 degrees Celsius, and suitable for filtration in environments with strong acids, strong alkalis, high temperatures, and high pressures. This series of products adopts a honeycomb structure with outer sparse and inner dense, which can effectively remove suspended solids and large particles of impurities in liquids. Specification Filter material: PP/degreased cotton/glass fiber Support frame material: PP/stainless steel Pore size: 1 ~ 100 micron Length: 5" ~ 60" Diameter: 61 ~ 105mm Interface type: 222, 226, DOE Gasket/O-rings: Silicone, EPDM, NBR, Viton, wrapped in PTFE Application Chemical industry: Filtration of electroplating solutions, chemical raw materials, coating solutions. Electronics industry: Pre-filtration of circuit board production line.
12" Inline Block Carbon Filter: Filters out chlorine, odors, and organic compounds to provide cleaner and better-tasting water. 12" Inline GAC Filter: Effectively removes chlorine, odors, and organic contaminants, improving the taste and purity of drinking water. 12" Inline Sediment Filter: Removes particles and suspended matter from water, ensuring clearer and healthier water. 10" Post Carbon Coconut Filter: Enhances water taste and purity by reducing residual contaminants, providing refreshing drinking water.
Vacuum Cleaner Filter Fabric Vacuum cleaner plays a very important role in keeping clean space of residential, commercial and industrial facilities, in where dust, dirt, human/pet hair, debris, mold and mildew will cause various allergies and sick. Role of Filters and Filter Media in Vacuum Cleaners All those accumulated airborne particles are picked up by the airflow produced by the vacuum cleaner and are captured by the filtration system to ensure that the environment you live in remains clean. Thatâ??s also why itâ??s so important that a vacuum cleaner must have a filter in it. Performance of a vacuum cleaner filter mostly corelates with the performance of filter fabric media. Higher filtration efficiency, lower pressure drop and better dust holding capacity finally come to better indoor air quality (IAQ), lower noise level, more suction power, and better durability of a filter. Advantages Of Mingguan Vacuum Cleaners Filter Media Solutions Mingguan provides various filter media for filter fabric manufacturers to meet specific requirements from different types of vacuum cleaner. The media materials include PP meltblown, electrostatic staple fiber mat, nano fiber media and PTFE membrane media. All these materials can combine with nonwoven carriers which provide excellent stiffness for pleating filters. Our product portfolio covers efficiency range from middle efficiency (for pre-filter) to HEPA and ULPA grade. If you want to know more about filter material for vacuum cleaner, please visit our website.
Production AR series PP precision filter is a professional filter developed and designed for the electronic componentsand chemical industry.The main body of the filter is made of PP material for injection molding. The main characteristics are acidand alkali resistance,high temperature resistance, corrosion resistance, idling resistance, no leakage, lownoise, high efficiency, wide filtration area, simple operation, easy cleaning and long service life. lt is widelyused in terminal filtration of electronic components and chemical industry. Item No.: AR-2005 Application: PCB, LED, Electroplating solution, organic solvent filtration Material: Polypropylene Product Size: 760*1420 mm Max Flow Rate: 150 L/mins Weight: 19.78 KG Filter cartridge Size: 20" X 5
