Electrical:Voltage rating: 125V AC rmsCurrent rating: 1.5AmpContact resistance: 100m Ohms (maximum)Insulation resistance: 1,000M Ohms (minimum) at 500V DCDielectric strength: 750V AC rms, 60Hz and one minute Environment:RCA Keystone Wallplate Insert(Gold plated)Storage temperature: -40 to +85°COperating temperature: 0 to 70°CConform to TIA/EIA 568B category 5eMates with modular plug conforming to UTP Cat.6Mechanical:Housing material: PC UL94V-0Inner material: flame-retardant ABS UL94V-0PCB material: FR-4Thickness: 1.6mmContact material: phosphor bronze stamp and PIN T=0.35mmIDC contact material: phosphor bronze, T=0.50mm with nickel platingWire: 24 to 26AWG
Material: carbon steel, stainless steel, alloy steel or according to customerâ??s requirement Material standard: ANSI, ASME, DIN, JIS, BS, GB or according to customerâ??s drawing Threaded standard: BSPT, NPT, BSP, DIN, ISO or according to customerâ??s requirement Technique: casting, CNC precision turning Size: according to customerâ??s requirement Service: ODM and OEM are available
1, Product Information: Rubber expansion joints are flexible connectors fabricated of nature rubber or synthetic elastomers, steel ring and fabrics, and when necessary, metallic reinforcements provide stress relief in piping systems due to thermal and mechanical vibration and/or movements. ZHW® Rubber Expansion Joints provide relief from stresses caused by thermal expansion and contraction in pipelines. Movement is always experienced in piping systems due to varying ambient temperatures, differences in temperature of materials handled, and differences in composition. Expansion joints absorb this movement and eliminate the danger of buckling or pulling apart with the high replacement costs that would result. 2, Product Advantages: Length of product customization Tough quality and Widely Service Absorption of Vibration, Noise and Shock Wide Range of Flange Materials Available Reduced Turbulence or Material Entrapment Compensation for Misalignment 3, Product Applications: It is extremely suitable for places where there are complex geologic conditions, large sedimentation range and pipes are easy to be damaged due to frequent alternation between heat and coldness in pipes. The elastic slide transfer and deformation of rubber and the heat dispersion of mechanical force may well prevent the physical damages from the displacement of pumps, valves and pipes. As a poor conductor, it is a harmless to reduce the vibration and noise transmission. The product is designed with smooth inner walls, after testing, it is proved to have no any influence on the flow speed and flux of medium, and keeps stainless for ever, accordingly it will be free of maintenance in operation.
Flexotech provides Camlock couplings in Bangalore which are manufactured with accuracy and precision. It is reliable, durable, and excels in performance and efficiency.
Stepper Motor Lead Screw Coupling CNC Flexible Shaft Coupler Features of shaft coupling 1) High concentricity, big torque 2) Aluminum material 3) Reducing the transmission of shock 4) Simple construction, easy to mount and maintenance 5) Suitable for stepper, servo, ballscrew Series commonly used on CNC engraving machine Series D40L55, Series D55L78, Series D65L90
This series hydraulic shaft couplings can be applied to the shipping and machinery industry in many fields.Due to the shaft with a handle couplings,greatly reduces the transmission shaft forging and machining cost. Remove after the cooperate parts while retain the original surface roughness,can be used repeatedly.
The features of this technology: 1.Strong intensity connector, stable and reliable; no specific requirements on the weld ability of the rebar; 2.Only needs 1-3m to stamp each connector, which is about ten times faster than ordinary welding; 3.Only 1-3 kw power of oil pump , which is not limited by power capacity, has flexible structure and suitable for operation on several machines; YJ650 stamping equipment 4.No flammable gases, not affected by rainy or cold weather; 5.Relieve congestion of the connecting point, facilitated concrete pouring; 6.No professional and experienced worker needed, able to connect changed steel bar of different diameters; 7.Save 80% of connector steel consumption. The technology is assessed by the Ministry of Construction as "world advanced, high quality, high efficiency, safe, and economical thick diameter distorted steel bar connection technology which can be widely used in the construction industry." Cold Extrusion Application Principle: 1.Place it well at the working point. 2.Directly use it to press connection point with screwless couplers to link the two rebar.
Introduction Hebei Yida Anti Impact Rebar Coupling system is a mechanical rebar splicing system, be made of high quality alloy steel. It has already passed the High Speed Tensile test of Anti instant impact by Germany Berlin BAM Laboratory. It has been widely applied at the sites where required high level of resistance to impact. The coupler sleeve will be perfect connected with rebar by cold swaged deformation in the application, and dual couplers will be connected by a high strength bolt.Its size can be from 12mm into 40mm different diameter bars. Special Advantages: (1)Each rebar is connected by cold swaged with a coupling, It was processed by large-tonnage hydraulic machine and unique split mould to ensure high quality and reliable radial deformation swage. (2)Rebar sleeve bond press is done prior to site connection saving precious site time. (3)The two sleeves are connected through a high-strength bolt, quality ensured. (4)Installation on site is easy and fast, even in dense cages. No X-ray check is needed and installation can be done in any weather conditions. (5)No thread cutting, no need heat or pre-heat on rebar, hence the rebar retains its original characteristics after splice. (6)The Yida ACJ rebar coupling system stands complex or full tension as well as full compression state. Application Guide: Proper installation is very important to ensure the design load will be reached in the application. Yida strongly recommends that the installation and site quality check be done according to the required guidelines and dimensions. Site installation method Step 1:Screw the bolt into female coupler swaged with rebar, till unable to screw continually. Step 2:Screw another side of bolt into the other sleeve after swaged with rebar, till unable to screw continually. Step 3:With help of two pipe wrench, tighten the connection by turning both rebar / couplers in opposite direction at the same time.
Bore dia:3-80mm OD:14-135mm Length:22-185mm Alloable speed: 2500-28000 Material: Aluminum alloy, steel Type: Screw type, clamp type
Standard taper thread couplers are designed to splice the same diameter bars where one bar can be rotated and the bar is not restricted in its axail direction. It is designed to achieve failure loads in excess of 115% of the charateristic strength of grade 500 rebar end. Working principle: 1. Slice up the end of the rebar. 2. Make the rebar taper thread cut by taper thread machine. 3. Connect together two taper thread end by one piece of taper thread coupler.
QUICK COUPLING Material: 304 / 316 / 304L / 316L Casting Process: Investment Casting Size: 1/2”-6” End type: Thread Threads: NPT / BSPT / BSP / DIN2999 / ISO7-1 / ISO228
Mode usage occasion Standard Model used in the occasion for connecting the steel bar in normal situation Different Diameter Model used for connecting the steel bar in different diameters Flared Model used for the steel bar which was hard to match Positive And Negative Screw Thread Model Used in the occasion when the steel bar in the two sides both can not be turned but the lengths can be adjusted. Locking Nut Model Used when the steel bar can not be turned, then it turns the splicing coupler to join the steel bar and then lock the splicing coupler with the locking nut.
Advantages: *Applies to bars from 14 to 40mm *No need of machines or specialized personnel for their application. *No torque gauge required, the screws are deheaded. *Comply with UK CARES, ACI318, ACI439 and cyclic load testing standards.
Casing with a separate power supply unit power supply of hydraulic tools to squeeze on steel. The final connection ensures a tensile strength of at least 125% of the nominal yield strength of the reinforcement grade 500 MPa.
GI Pipe Couplings are manufactured using high-grade material. We provide an extensive range of these products to our clients at cost-effective rates which are appreciated for stability, resistance to corrosion, and effectiveness in application.
A forged coupling is a type of pipe fitting that is made by forging, a process that uses heat and pressure to shape metal. Forged couplings are typically made of steel, but they can also be made of other metals such as stainless steel, alloy steel, and copper. Forged couplings are stronger and more durable than other types of pipe fittings, such as threaded couplings. They are also less likely to leak. Forged couplings are used in a variety of applications, including water, gas, and oil pipelines, as well as in industrial and construction applications. Here are some of the technical specifications of forged couplings: Material: Steel, stainless steel, alloy steel, copper Class: 2000, 3000, 6000, 9000 Size: 1/8 to 4" End type: Socket weld, threaded, flanged Size: Typically available in sizes from 1/2 inch to 12 inches
A forged half coupling is a type of pipe fitting that is used to connect two lengths of pipe. It is made of forged steel, which gives it a high strength and durability. The half coupling has a threaded end that screws onto one end of the pipe, and a socket end that is welded or flanged to the other end of the pipe. Here are the technical specifications of a forged half coupling: Material: Forged steel Sizes: 1/4 inch to 4 inches Pressure ratings: 2000 psi, 3000 psi, and 6000 psi Temperature ratings: Up to 1000 degrees Fahrenheit Thread types: NPT, BSP, and BSPT Finishes: Black, galvanized, and stainless steel
A forged threaded coupling is a type of pipe fitting that is used to connect two lengths of threaded pipe. It is made from a solid piece of metal that is then threaded on both ends. Forged threaded couplings are typically made from steel, stainless steel, or brass. They are available in a variety of sizes and pressure ratings. Specifications: Material: Carbon steel, stainless steel, alloy steel, nickel alloy Size: 1/8 inch to 4 inches NPS Pressure rating: Varies depending on material and size Thread type: NPT, BSP, BSPT Finish: Black, galvanized, stainless Applications: Oil and gas industry, chemical processing industry, petrochemical industry, water treatment industry, HVAC industry, fire sprinkler industry
Rebar range 16-40mm, No limitations on the type, composition, or weldability of steel bars, it's widely used in bridge construction.
Hebei Yida Anti Impact Rebar Coupling system is a mechanical rebar splicing system, be made of high quality alloy steel. It has already passed the High Speed Tensile test of Anti instant impact by Germany Berlin BAM Laboratory. It has been widely applied at the sites where required high level of resistance to impact. The coupler sleeve will be perfect connected with rebar by cold swaged deformation in the application, and dual couplers will be connected by a high strength bolt.
