for the measurement of electrical variables in heavy current power system RISH Ducer M40 (Fig. 1) is a programmable transducer with a RS 485 bus interface (MODBUS ). It supervises several variables of an electrical power system simultaneously and generates 4 proportional analogue output signals. The RS 485 interface enables the user to determine the number of variables to be supervised (up to the maximum available). The levels of all internal counters that have been configured (max. 4) can also viewed. Provision is made for programming the RISH Ducer M40 via the bus. A standard EIA 485 interface can be used, but there is no dummy load resistor for the bus. The transducers are also equipped with an RS 232 serial interface to which a PC with the corresponding software can be connected for programming or accessing and executing useful ancillary functions. This interface is needed for bus operation to configure the device address, the Baud rate and possibly increasing the telegram waiting time (if the master is too slow) defined in the MODBUS protocol. The usual methods of connection, the types of measured variables, their ratings, the transfer characteristic for each output and the type of internal energy metering are the main parameters that can be programmed. The ancillary functions include a power system check, provision for displaying the measured variably on a PC monitor, the simulation of the outputs for test purposes and a facility for printing nameplates. The transducer fulfils all the essential requirements and regulations concerning electromagnetic compatibility(EMC) and safety (IEC 1010 resp. EN 61 010). It was developed and is manufactured and tested in strict accordance with the quality assurance standard ISO 9001. nSimultaneous measurement of several variables of a heavycurrent power system / Full supervision of an asymmetrically loaded four-wire power system, rated current 1 to 6 A, rated voltage 57 to 400 V (phase to neutral) or 100 to 693 V (phase-ton phase) nFor all heavy-current power system variables n4 analogue outputs nInput voltage up to 693 V (phase-to-phase) nUniversal analogue outputs (programmable) High accuracy: U/I 0.2% and P 0.25% (under reference nconditions) 4 integrated energy meters, storage every each 203 s, storage nfor: 20 years Windows software with password protection for programming, data analysis, power system status simulation, acquisition of nmeter data and making settings DC-,AC-power pack with wide power supply tolerance / nuniversal Provision for either snapping the transducer onto top-hat rails or securing it with screws to a wall or panel
Toshiba PVT-661VT Endovaginal 10mm transducer 1.Type: Endovaginal 2.Frequency: 3-9MHz 3.Compatible system: Aplio 50 SSA-700A, Aplio SSA-750A, Xario SSA-660A 4.Condition: pre-owned and original, in good working condition 5.With 60 days warranty
Toshiba PLT-805AT Linear 56 mm Ultrasound Transducer 1.Type: linear 2.Frequency: 6.2-12.0 Mhz 3.Compatible system: Aplio 50 SSA-700A, Aplio SSA-750A, Aplio SSA-770A, Xario SSA-660A 4.Application: peripheral vascular and small part 5.Condition: pre-owned and original, in good working condition 6.With 60 days warranty
I221LY05-25 I222LY05-25 I224LY05-25 Output signals 0-5V AC/DC 0-5V DC 4-20mA Responding time 50us 100ms 150ms Power supply ±12V, ±15V DC ±12V, ±15V, +12V, +24V DC
Attribute: 1.Input: DC 0~1mA...0~5A; 2.Output: DC(0)4-20mA 3.Accuracy : 0.5% 4.Input Impedance (R): Riï¼?0.05V/Ix (Ix is the current be measured) 5.Linear Range:0-120% of nominal input 6.Responding Time: 150ms 7.Over Load Capacity: 10 times of nominal input, for 5 seconds; 8.Maximum Load: 6V 9.Static current: 17mA 10.Auxiliary Power:+12Vdc +24Vdc 11.Isolation Voltage: â?¥2500Vdc, for 1 minute 12.Output Ripple: ï¼?10mV 13. Drifting by Temperature: 350Ã?10-6/ 14. Ambient Temperature: -10ï½?+50 15. Mounting : DIN Rail 35mm Mounting
Attribute: Rated input current 1mA, 5mA, 20mAâ?¦5A DC Output signals 0-5V, 0-10V DC Accuracy 0.2% Input Impedance (R) approximate zero Responding Time 350ms Linear measuring range 0 - 1.2 times of rated input current Over Load Capacity 30 times of rated input current, 5s Frequency range 25Hzï½?5kHz Output impedance 6V Static current 10mA Power supply +12V, +24V DC Isolation Voltage(Input/Output) â?¥2500Vdc, for 1 minute Output Ripple ï¼?6mV Thermal drift 200ppm/°C Ambient Temperature -25ï½?+50 Mounting DIN Rail 35mm Mounting or screw mounting Material of shell ABS (According to UL94V-0) Protection of shell IP20 Shell type without aperture MTBF >50000h Weight 90g
Attribute: Rated input current AC 30A, 50A, 100A, 150A, 200A, 250A, 300A, 350A, 400A AC Output signals 4-20mA DC Accuracy 0.5% Input Impedance (R) approximate zero Responding Time 300ms Linear measuring range 0 - 1.2 times of rated input current Over Load Capacity 30 times of rated input current, 5s Frequency range 25Hzï½?5kHz Output impedance 6V Static current 3.3mA(0mA-20mA) 6.8mA(4mA-20mA) Power supply +12V/+24V DC Isolation Voltage(Input/Output) â?¥2500Vdc, for 1 minute Output Ripple ï¼?6mV Thermal drift 350ppm/°C Ambient Temperature -10ï½?+50 Mounting DIN Rail 35mm Mounting or screw mounting Material of shell ABS (According to UL94V-0) Protection of shell IP20 Shell type with aperture Ф20mm MTBF >50000h Weight 120g
Attribute: Rated input voltage 10mV, 50mV, 75mV, 5V, 50V, 75V, 150V, 200V, 300V, 400V, 500V, 750V, 1000V DC Output signals 0-20mA, 4-20mA DC Accuracy 0.2% Input Impedance (R) approximate zero Responding Time 350ms Linear measuring range 0 - 1.2 times of rated input current
Attribute: Rated input voltage 10mV, 50mV, 75mV, 5V, 50V, 75V, 150V, 200V, 300V, 400V, 500V, 750V, 1000V AC Output signals 0-5V ,0-10V DC Accuracy 0.2% Responding Time 200ms Linear measuring range 0 - 1.2 times of rated input current Over Load Capacity 10mA Static current 6mA Power supply DC 12V, 24V
Rated input current AC 50A, 100A, 400A AC/DC Accuracy 1.0 Input Impedance (R) approximate zero Linear measuring range 0 - 1.2 times of rated input current Over Load Capacity 30 times of rated input current, 5s Frequency range 25Hzï½?5kHz Isolation Voltage(Input/Output) â?¥2500Vdc, for 1 minute Thermal drift 600ppm/°C Ambient Temperature -25ï½?+70 Mounting DIN Rail 35mm Mounting or screw mounting
Rated input current AC 20A, 30A, 40A, 50A, 70A, 90A, 100A AC Output signals 0-20mA ,4-20mA DC Accuracy 1.0 Input Impedance (R) approximate zero Responding Time 300ms
Rated input current AC 50A, 100A, 400A AC/DC Accuracy 1.0 Input Impedance (R) approximate zero Linear measuring range 0 - 1.2 times of rated input current Over Load Capacity 30 times of rated input current, 5s Frequency range 25Hz~5kHz Isolation Voltage(Input/Output) 2500Vdc, for 1 minute Thermal drift 600ppm/ Ambient Temperature -25~+70 Mounting DIN Rail 35mm Mounting or screw mounting
I221LY05-25I222LY05-25I224LY05-25 Output signals0-5V AC/DC0-5V DC4-20mA Responding time50us100ms150ms Power supply12V, 15V DC12V, 15V, +12V, +24V DC
Product Introduction: PT4XX6 series pressure transducers are ideal for the measurement of melt pressure in extrusion processes at temperatures up to 400 . This series are produced with special materials and alloyed elastic diaphragm together with delicate processing and debugging. The main characteristics are high accuracy and small zero and span shifts caused by changes in process temperatures Performance Parameters: Pressure Range: 0 ~ 5MPA ~ 150 MPA ( 0 ~ 750psi ~ 20000psi ); Accuracy: ±0.5% FS; Power: 10VDC ( 6 ~ 12 V DC ); Output Signal: 3.33mV/V (Default), 3.0mV/V(Optional) etc. Probe Heat Resistance: PT4516 Series: 300°C; PT4616 and PT4626 Series: 400°C; Temperature Drift: =500MΩ/500VDC Mechanical Connections: 1/2"-20UNF, M10x1.5, M12x1.5, M14x1.5, M18x1.5, M22x1.5 etc. (Optional) Electrical Connections: 6PIN (SD02106P/SD02106S) Thermometric Config: Thermocouple: E, J, K, S type etc.; (PT4626 Series Optional) Thermal Resistance: Pt100 etc. (PT4626 Series Optional) Features: * Anticorrosive wear-resisting coating: apply to high concentrations of rough media pressure measurement, can improve the service life of 3 to 5 times (optional); * Special requirement can make to order, delivery date 7 ~ 15 working days; * Optional supporting intelligent digital pressure meter: Order Format: Example1: PT4516-350bar-M18-150-3.0mV/V Note: Product design Model "PT4516". Function code "Null" stands for melt pressure transducer. Coating code "Null" stands for without coating . Pressure range: 0 ~ 350bar. Thread size : M18 * 1.5. Rigid stem length:150mm . Pressure output signal: 3.0mV/V. Example2: PT4616-50MPa-1/2"-20-150/470-3.33mV/V Note: Product design Model "PT4616". Function code "Null" stands for melt pressure transducer. Coating code "Null" stands for without coating . Pressure range: 0 ~ 50MPa. Thread size : 1/2"-20UNF . Rigid /Flexible length:150mm/470mm . Pressure output signal: 3.33mV/V. Example3: PT4626-50MPa-M14-150/470-J-3.33mV/V Note: Product design Model "PT4626". Function code "Null" stands for melt pressure transducer. Coating code "Null" stands for without coating . Pressure range: 0 ~ 50MPa. Thread size : M14*1.5 . Rigid /Flexible length:150mm/470mm . Thermometric config: J type thermocouple temperature sensor . Pressure output signal: 3.33mV/V.
APT Key Features The sensor design is based on ceramic capacitor structure. All signal processing circuits are gathered together as one application-specific integrated circuit. Allowable for a wider temperature range (-40¢FXC to +135¢FXC ). Allowable pressure range is up to 3,000psi. Precise assembly process; no further adjustment is required after leaving factory. Absolute or relative pressure sensor. A reliable package type especially designed for engine and chassis installation. Accurate and stable output signal. Able to fit for all auto pressure liquids. Able to enhance the temperature output. APT Operation Principle
We provide OEM,ODM service,you can customized your own design,put with your logo etc From coil to the magnetic sheet/plastic or electronic parts/accessories,we can provide one step solution service with cost saving . You can customized the wire material,wire size,coil dimension,coil turns, coil thickness, magnet,leading wire,resistance, inductance etc. Wire size: start from 0.011mm -1.3mm /customized Coil Size: 0.1-3MM To 300MM /Customized Wire material:enameled copper wire,silk cover /customized winding style: self-adhensive, wet winding by automatic and semi-automatic machine over 400 Coil Style:inductor coil,self-bonding coil,bobbin coil, hearing adis coil, antenna coil, ,RFID Coil, Sensor Coil, Transformers,inductors, Application of precision coil: Hearing Aids,sound amplifiers,bluetooth,high-end earphone,medical equipment and instruction etc. Customized service included: Wire material Wire size Coil height Number of Coil Inductance DCR Etc Customized process options Clients Provide the design drawing Clients Provide the Samples Clients Provide the detailed data and requirements Supply drawing is best, or tell us the size, inductance, resistance, Q value, OD, ID, Turns, thickness, etc. Sample lead time 1-3 days Sample delivery Ship via your agent Ship via DHL/UPS/TNT/FEDEX/China Post Bulk order Lead Time 7-15 Days Supply Ability Of our factory 1000000 Piece/Pieces per Month Quality Certification:ISO14000,ISO9000,ISO9001 IATF16149 Test Equipment/Laboratory certification: 1:High-Potting 2:combustion flame retardant experiement 3:Cold and hot shock/Thermal Shock 4: constant temperature and humidity test 5: Drop Test 6:the vibration test 7: PCT High pressure accelerated aging test 8: 2D Profile/two dimensional image measurements 9" X-ray fluorescence ETC Package: plastic bag. blister divider,carton etc customized as per your products feature Shipment BY AIR,BY EXPRESS,BY SEA,BY TRAIN ETC EX-WORK,FOB,CIF,DDP,DDU etc Payment term: T/T L/C 30% Deposit and balance before shipment
Our company established in 1995, has more than 10 years experience in making resistance welding machines and induction heating equipment. To meet the demand of Smaller and Portableâ heating needs, we developed the KIA-1KW mini induction heater with our partner in Europe. This device adopt Electro-Magnetic induction theory, can fast heat small metal parts on auto or machines. Mainly used for heating Rusted/ Frozen/ Corrosive Bolt, Nut, Fasteners, Suspension Nut, Gears, Pulley, and Bearings etc. Meanwhile, it also can help removing stickers on cars. Heating Abilities: In around 30 seconds, it can heat a 20mm diameter bolt to a temperature above 300 C, maximum temperature can reach around 750 C. The advantage if using this device is it is totally flameless, comparing with traditional way of heating by fire, it is much safer and of higher work efficiency, without the worry of harming the adjacent area. Light weight, do not need water cooling, and very easy to use.
PAGOODA chip inductor introduction: Volume: 0402, 0603, 0805, 1206, 2520, 3225 4532, 5650 Sensitivity: 12NH, 15NH, 22NH, 39NH, 68NH 1R0K, 1R2K, 2R2K2R7K, 3R3K, 4R7K10uH, 15uH12uH18u22H1MH12MH 1.5MH18MH2.2MH...... Error: J=+5%K=±10%M=±20%, N=±30% Inductors used in power supply mounting and circuits are produced with metal composite materials or ferrite materials. It is mainly used for circuits that realize voltage conversion that requires a specific voltage to provide stable power for ICs. The corresponding inductor is used in the power supply circuit, maintains the inductance when the current allows, and has the characteristics of low square resistance. High Current Slow down saturation and maintain high current characteristics Low RDC Improves high current efficiency through low branch resistance PAGOODA high-end technology electronic component manufacturers, chip inductors have complete specifications, can provide samples, quality assurance, comprehensive technical support, welcome to inquire
Product name: I-shaped inductor Category: SMD inductor series Product introduction: Volume: 0402, 0603, 0805, 1206, 2520, 3225, 4532, 5650 Tolerance: I=�±7%, K=�±10%, L=�±15%, M=�±20% Sensation: 1.2N 1.5N 2.2N 3.9N 6.8N...... 1R0K 1R2K 2R2K 2R7K 3R3K 4R7Kâ?¦ 10u 15u 12u 18u 22uâ?¦ 1MH 1.2MH 1.5MH 1.8MH 2.2MHâ?¦ Features: 1. High dimensional precision wire wound inductors suitable for automatic placement; 2. Good solderability; 3. Heat-resistant resin encapsulation, with excellent mechanical strength; 4. Excellent Q value and high reliability; 5. Used in LCD TVs, computer drives, mobile phones, car audio and other electronic products. Order Hotline: 400-003-5559 I-shaped inductor, the role of the inductor, the inductance formula, the unit of the inductor, the chip inductor package, the inductor, the chip power inductor, the one-piece inductor, the chip inductor specification, the I-shaped inductor, the chip I-shaped inductor specification, Shielded I-shaped inductor, SMD inductor tdk, SMD inductor pdf, SMD inductor 47uh, SMD inductor 470, SMD inductor 330uh, SMD inductor 2.2uh, buy SMD inductor,
Product Name: Common Mode Inductor Product parameters (product overview) volume: 0402, 0603, 0805, 1206, 2520, 3225, 4532, 5650 Tolerance: I=±7%, K=±10%, L=±15%, M=±20% Sensitivity: 1.2N 1.5N 2.2N 3.9N 6.8N...... 1R0K 1R2K 2R2K 2R7K 3R3K 4R7K 10u 15u 12u 18u 22u 1MH 1.2MH 1.5MH 1.8MH 2.2MH Features: 1. High dimensional precision wire wound inductor suitable for automatic placement; 2. Good solderability; 3. Heat-resistant resin encapsulation with excellent mechanical strength; 4. Excellent Q value and high reliability; 5. Used in LCD TVs, computer drives, mobile phones, car audio and other electronic products.