Price - Through mail Only Procedure - CIF , ASWP Origin - Russia Min- Max - 50K-100K MT Contract - Spot/12 month Payment Term - SBLC/DLC/ MT 103
Price - Through mail Only Procedure - CIF , ASWP Origin - Russia Min- Max - 25K-50K MT Contract - Spot/12 month Payment Term - SBLC/DLC/ MT 103
Price - Through mail Only Procedure - CIF , ASWP Origin - Russia Min- Max - 50K-100K MT Contract - Spot/12 month Payment Term - SBLC/DLC/ MT 103
We have established all facilities such as storage of raw material, blending, filling in to small/ big packs, quality control and storage of finished goods all under one roof. We strongly believe in delivering quality product to our customers. We have established and incorporated high quality standards OUR INDUSTRIAL LUBRICANTS PRODUCT RANGE HYDRAULIC OIL GEAR OILS TURBINE OIL COMPRESSOR OIL REFRIGERATION OIL SLIDEWAY OIL SPINDLE OILS SUGAR MILL ROLL-BEARING OIL Heat Transfer Oil Cylinder Oil Vacuume Oil
Penetration Grade Comments 40 - 50 Hardest grade. 60 - 70 Typical grades used in the U.S. 85 - 100 120 - 150 200 - 300 Softest grade. Used for cold climates such as northern Canada Penetration Grade Bitumen Specification (AASHTO M 20 and ASTM D 946) Units 40/50 60/70 80/100 100/120 Test Methods Specific Gravity @25 C - 1.01-1.06 1.01-1.06 1.01-1.05 1.01-1.04 ASTM D-70 Penetration @25 C, 100gm, 5sec 0.1MM 40-50 60-70 80-100 100-120 ASTM D-5 Softening Point, Ring & Ball C 52-60 49-56 45-52 42-49 ASTM D-36 Ductility @25 C, after TFOT, Min CM 100 100 100 100 ASTM D-113 Loss on Heating, Max %Wt 0.2 0.2 0.5 0.5 ASTM D-6 Drop in Penetration after Heating, Max % 20.0 20.0 20.0 20.0 ASTM D-6 & D-5 Flash Point Cleveland open cup, Min C 250.0 250.0 232.0 250.0 ASTM D-92 Solubility in CS2, Min %Wt 99.5 99.5 99.5 99.5 ASTM D-4 Organic Matter Insoluble in CS2, Max %Wt 0.5 0.5 0.5 0.5 ASTM D-4 Sport Test - Negative Negative Negative Negative *A.A.S.H.O.T.102 Viscosity Grade Standard Grading based on Original Asphalt (AC) Grading based on Aged Residue (AR) AASHTO M 226 AC-2.5 AC-5 AC-10 AC-20 AC-30 AC-40 AR-10 AR-20 AR-40 AR-80 AR-160 ASTM D 3381 AC-2.5 AC-5 AC-10 AC-20 AC-30 AC-40 AR-1000 AR-2000 AR-4000 AR-8000 AR-16000 Standard Grades Minimum of Absolute Viscosity, Poise@ 600�°C Approximate penetration grade IS73:2013 VG 10 800 80-100 VG 20 1600 - VG 30 2400 60-70 VG 40 3200 30-40/40-50 Viscocity grade over penetration grade several key issues are addressed, like: Viscosity Grade Bitumen Specification (IS 73:2013) Property Units VG-10 VG-20 VG-30 VG-40 Test Methods Penetration at 25�°C, 100g, 5sec, Min 0.1MM 80 60 45 35 IS 1203 Absolute viscosity at 60�°C P 800-1200 1600-2400 2400-3600 3200-4800 IS 1206 (Part 2) Kinematic viscosity at 135�°C, Min cSt 250 300 350 400 IS 1206 (Part 3) Flash point (Cleveland open cup), Min �°C 220 220 220 220 IS 1448 [P : 69] Solubility in trichloroethylene, Min %Wt 99 99 99 99 IS 1216 Softening point (R&B), Min �°C 40 45 47 50 IS 1205 Tests on residue from thin film oven test: - Viscosity ratio at 60�°C, Max 4 4 4 4 IS 1206 (Part 2) - Ductility at 25�°C, Min CM 75 50 40 25 IS 1208
Typical Properties of Each Base Oil Group Group  Group Group Ultra-S 4,6,8 Group Saturates, % 65~85 93~99+ 95~99+ 99+ 99+ Aromatics, % 15~35
Bitumen emulsions are usually dispersions of minute droplets of bitumen in water and are examples of oil-in-water emulsions. The bitumen content can be varied to suit different requirements and is typically between 30% and 70%. The primary objective of emulsifying bitumen is to obtain a product that can be used without the heating normally required when using cutbacks and paving grade bitumen. In the manufacture of bitumen emulsions, hot bitumen is sheared rapidly in water containing an emulsifying chemical (emulsifier). This produces very small particles of bitumen (the dispersed phase) dispersed in water (the continuous phase). The bitumen particles are stabilized in suspension and do not readily coalesce due to the presence of the emulsifier, which is concentrated on the surface of the bitumen particles. During application, the water in a bitumen emulsion is either lost by evaporation, or it may separate from the bitumen because of the chemical nature of the surface to which the emulsion is applied. This process is referred to as breaking. Because bitumen has a density only slightly higher than water, sedimentation of the bitumen droplets in an emulsion during storage is very slow. Emulsions can usually be regenerated after long storage times by gentle stirring to re-disperse the bitumen droplets.
Standard Viscosity Grade Bitumen (AC-Grades), in which the Viscosity of the standard bitumen (asphalt) is measured at 60 C (140 F). RTFOT Viscosity Grade Bitumen (AR-Grades), in which the Viscosity of bitumen (asphalt) is measured at 60 C (140 F) after the roll on thin film oven test. Viscosity grade bitumen have a thermoplastic property which causes the material to soften at high temperatures and to harden at lower temperatures. This unique temperature/ viscosity relationship is important when determining the performance parameters such as the adhesion, rheology, durability and application temperatures of bitumen. In the Viscosity Graded Bitumen specifications further special emphasizes is placed on the Bitumen ductility.
Performance Grade (PG) bitumen is bitumen which is graded based on its performance at different temperatures. The Long-Term Pavement Performance(LTPP) has given certain algorithm to calculate the temperature of the pavement based on the temperature of the air above. From this, the highest and the lowest temperatures of the pavement is calculated and the bitumen that performs well in that temperature range is selected. Penetration grading and viscosity grading are somewhat limited in their ability to fully characterize asphalt binder for use in Hot Mix Asphalt(HMA) pavement. Therefore, as part of the Superpave research effort new binder tests and specifications were developed to more accurately and fully characterize asphalt binders for use in HMA pavements. These tests and specifications are specifically designed to address HMA pavement performance parameters such as rutting, fatigue cracking and thermal cracking.
Group I base oils are classified as less than 90 percent saturates, greater than 0.03 percent sulfur and with a viscosity-index range of 80 to 120. The temperature range for these oils is from 32 to 150 degrees F. Group I base oils are solvent-refined, which is a simpler refining process. This is why they are the cheapest base oils on the market.
Group II base oils are defined as being more than 90 percent saturates, less than 0.03 percent sulfur and with a viscosity index of 80 to 120. They are often manufactured by hydrocracking, which is a more complex process than what is used for Group I base oils. Since all the hydrocarbon molecules of these oils are saturated, Group II base oils have better antioxidation properties. They also have a clearer color and cost more in comparison to Group I base oils. Still, Group II base oils are becoming very common on the market today and are priced very close to Group I oils.
Bitumen emulsions are usually dispersions of minute droplets of bitumen in water and are examples of oil-in-water emulsions. The bitumen content can be varied to suit different requirements and is typically between 30% and 70%. The primary objective of emulsifying bitumen is to obtain a product that can be used without the heating normally required when using cutbacks and paving grade bitumen. In the manufacture of bitumen emulsions, hot bitumen is sheared rapidly in water containing an emulsifying chemical (emulsifier). This produces very small particles of bitumen (the dispersed phase) dispersed in water (the continuous phase). The bitumen particles are stabilized in suspension and do not readily coalesce due to the presence of the emulsifier, which is concentrated on the surface of the bitumen particles. During application, the water in a bitumen emulsion is either lost by evaporation, or it may separate from the bitumen because of the chemical nature of the surface to which the emulsion is applied. This process is referred to as breaking. Because bitumen has a density only slightly higher than water, sedimentation of the bitumen droplets in an emulsion during storage is very slow. Emulsions can usually be regenerated after long storage times by gentle stirring to re-disperse the bitumen droplets.
Gilsonite is a natural, resinous hydrocarbon found in the Uintah Basin in northeastern Utah; thus, it is also called Uintaite. This natural asphalt is similar to a hard petroleum asphalt and is often called a natural asphalt, asphaltite, uintaite, or asphalt. Gilsonite is soluble in aromatic and aliphatic solvents, as well as petroleum asphalt. Due to its unique compatibility, Gilsonite is frequently used to harden softer petroleum products. Gilsonite in mass is a shiny, black substance similar in appearance to the mineral obsidian. It is brittle and can be easily crushed into a dark brown powder. When added to asphalt cement or hot mix asphalt in production, Gilsonite helps produce paving mixes of dramatically increased stability. We can provide based on customer requests Packing will standard approved packing
Group III base oils are greater than 90 percent saturates, less than 0.03 percent sulfur and have a viscosity index above 120. These oils are refined even more than Group II base oils and generally are severely hydrocracked (higher pressure and heat). This longer process is designed to achieve a purer base oil. Although made from crude oil, Group III base oils are sometimes described as synthesized hydrocarbons. Like Group II base oils, these oils are also becoming more prevalent.
Hello Buyer/Buyer Mandate, I am direct mandate to end seller/refineries here in Russia Federation, our refineries can supply to you/your buyers it's products, PETCOKE,M100, D6,D2,JETA1,AGO,LCO,ESPO,JP54, LNG, LPG,DIESEL FUEL EN-590 ULSD, without any delay nor complication.
Hello , We are direct mandate to Russia Refinery, direct suppliers of petroleum/petrochemical products. Our suppliers do supplies products to any safe port in the world. We are connected to the most reputable Russian Refineries and negotiate transactions on behalf of buyers and our refineries. Our petroleum products' best specifications with the best prices as well. Below are the products we have available for an urgent lift in the port of Rotterdam and Russia. Products available for FOB Rotterdam: D6, JET A1, JP54, D2, EN590, LNG & LPG. Products available on CIF Basis: D6, JET A1, JP54, D2, EN590, LNG & LPG, REBCO, Mazut, Bitumen, Urea. Please only for serious buyers or mandate to the buyer.
Hello , We are direct mandate to Russia Refinery, direct suppliers of petroleum/petrochemical products. Our suppliers do supplies products to any safe port in the world. We are connected to the most reputable Russian Refineries and negotiate transactions on behalf of buyers and our refineries. Our petroleum products' best specifications with the best prices as well. Below are the products we have available for an urgent lift in the port of Rotterdam and Russia. Products available for FOB Rotterdam: D6, JET A1, JP54, D2, EN590, LNG & LPG. Products available on CIF Basis: D6, JET A1, JP54, D2, EN590, LNG & LPG, REBCO, Mazut, Bitumen, Urea, ESPO Please only for serious buyers or mandate to the buyer.
Jambo bags grade 60/70 All grade's of Iranian bitumen Grades PG: 40/50, 60/70, 80/100 VG: VG10, VG20, VG30 MC10, MC20 etc
Bonny light Crude oil
Base oil SN150
