5mm to 0.1 mm dia in Enameled Copper Magnet Wire Polyester Covered Copper Magnet Wire Temp Class 130, Modified Polyester Covered Copper Magnet Wire Temp Class 155, Polyesteremide Covered Copper Magnet Wire Temp Class 180, Polyesteremide-amide Covered Copper Magnet Wire Temp Class 200, Polyurethane Covered Copper Magnet Wire Temp Class 155 and 180, 1 Sqmm to 36 Sq mm in Enameled Strips, min, width 1mm and min. thickness 0.8 mm. Polyester Covered Copper Magnet Strip Temp Class 130, Modified Polyester Covered Copper Magnet Strip Temp Class 155, Polyesteremide Covered Copper Magnet Strip Temp Class 180, Polyesteremide-amide Covered Copper Magnet Strip Temp Class 200, Paper covered Copper wire and Paper covered Copper Strip,Fibre Glass Covered Copper Wire, Fibre Glass Covered Copper Strips, Enameled Fibre Glass Covered Copper Wire, Enameled Fibre Glass Covered Copper Strips Wires in 2.5 Kg to 90 Kg Packing as per Specification, in Min lot of 10 MT and above, Strips in 50 Kg to 100 Kg in Wooden Spools.
A highly efficient wire known for its high tensile strength, durability, cost effectiveness, rust and abrasion resistance, as well as being scratch-free, water and corrosion proof, with accurate dimensions. One of the best wires known for making umbrella ribs, these wires require low maintenance and operating cost, and can be easily customized in different shapes and sizes. Used to design various types of ropes, spring and wire forms, and cables, these wires are available at very nominal prices. Technical specifications: Carbon Content - 0.35% To 0.40% Sizes1.55 Mm To 2.20 MM Oil Or Without Oil (As Per Preference) Phosphate Coated
HC Wires are used in various applications that require hardness and high tensile strength. These wires are available in high, medium, low carbon steel in sizes varying from 0.50 MM to 12.00 MM with carbon content from 36 to 85. These wires are available in various finishes such as annealed, wires phosphate coated and clean surface. These wires can be customized as per your requirement to get the hardness, tensile strength, torsion, coil weight and size tolerance as you require. Technical specifications: Diameter : 0.50 â?? 12.00 MM Coil Wt. : 40 to 400 kg Phosphate Coating Finish : Black (Oil & Without Oil) Packing : Coil with plastic wrapping
Si: 58% min Ca: 30% min S: 0.5% max P: 0.02% max C: 2% max Al: 1.5% max Wire Diameter: 13 mm +/-0.5mm Powder Weight: 230+/- 5gm / meter Steel Weight: 160+/- 5gm / meter Wire Thickness: 0.4 mm +/-0.3 mm Length of coil: App. 5200 m Coil Height: 1200mm Coil ID: 550 mm Coil OD: 1100 mm Packing: on Pallets
2601 Stryker Neurovascular Synchro 2 GuidewireGuidewire with Hydrophilic Coating 0.014in x 200cm. Box of 1
Product OverviewDesigned to be your first choice coronary guidewire The RUNTHROUGH NS Extra Floppy is designed to be an all-in-one workhorse wire with a soft, atraumatic, low tip weight wire that can be used to access most everyday and complex lesions.
Radifocus Guidewire M Standard type is a Nitinol hydrophilic guidewire covered with polyurethane containing tungsten and a hydrophilic polymer coating (M Coat) for complete, low friction maneuverability. Indicated for use for standard angiography in coronary and peripheral territories, catheterization, embolization, peripheral angioplasty and stenting (with or without an exchange wire), and subintimal angioplasty in small, standard or large proximal or distal vessels.
Frontline Workhorse guide wires are designed to be flexible, have a soft tip, and provide enough support to deliver most interventional devices. All Hi-Torque Guide Wires are intended to facilitate the placement of balloon dilatation catheters during percutaneous transluminal coronary angioplasty (PTCA) and percutaneous transluminal angioplasty (PTA). This HI-TORQUE Guide Wire is intended to facilitate the placement of balloon dilatation catheters during Percutaneous Transluminal Coronary Angioplasty (PTCA) and Percutaneous Transluminal Angioplasty (PTA). This guide wire may also be used with compatible stent devices during therapeutic procedures.
Width 3.7MM Colour White Content HDP with GI Metal Wire Packing 500 meters per roll, 6 rolls in a Box. Usage- In surgical and disposable masks
We are manufacturers of various sizes of binding wire. -
We are manufacturers of various sizes of binding wire. -
Tyre bead wire is a high quality carbon metal. It is incorporated in the structure of the tyre to withstand bumps, heat and other hazardous conditions. radial tyre bead wire is 1.6 mm and nylon tyre bead wire is 1.10mm. Therefor, the wire obtained from end of life tyres is also of high quality matieral and resuing it can be a highly lucrative for the businesses as well as the environment. Scrap Bead Wire is used in converting to shot blasting, high tension springs, wire mesh, wire baskets, nails, cutting tools. Since this is extracted from tyres it is available at a very reasonable rates. A Scrap truck or Bus Tyre consists of 20-25% of high quality steel in it. The metal bead wire is obtained when the waste tyre is put into the shredding machines. It is very important to derive the bead wire in one single piece. The wire can easily be oxidised so protecting it from different atmospheric agents is important. So to meet our clients' expectations, we have set strict standards and quality control techniques. )
This steel has a high carbon content and is of good grade. It is built into the construction of the tyre to endure bumps, heat, and other potentially dangerous situations. As a result, recycled tyre wire is of very high quality and meets industry standards. To prevent machines farther down the processing line from usury, contemporary technologies tend to remove the wire as soon as possible. Pre-shredding is commonly followed by a first granulation step, in which the rubber chips are filtered through a 15 to 25 mm screener, depending on the plant layout. A magnetic mechanism separates the steel wire from the rubber immediately after this granulation. Along with the wires, 10 to 35 percent by weight of rubber and textiles are removed, hence the total material recovery varies depending on the contamination grade of the material (rubber/fiber). Steel typically makes up 10% to 20% of the weight of an old passenger car tyre. A typical shredding factory generates huge quantities of steel tyre wire, with quality varying depending on the technology, storage, and management systems used by the factories. Another important component in assessing the material's quality is the steel's resistance to atmospheric agents. The material is quickly oxidised since it is shaped in tiny wires. As a result, protecting the wire from any atmospheric contaminants is an important part of improving its quality.
DESCRIPTION : It is galvanized steel barbed wire with two strands of wire used for fencing. APPLICATION : Used in fencing Type A: The wire has four points and is formed by twisting two points wire, each two turns, tightly around both line wires. Specification : IS:278 SIZE RANGE : All Sizes Material : The galvanized barbed wire is manufactured from galvanized mild steel wire conforming to IS: 280 Galvanizing : The barbed wire is galvanized and the galvanizing requirements as laid down for medium coated wire of IS:4826 specification for galvanized coating on the round wire. Packing: The coils are normally supplied in the bare condition.
DESCRIPTION : The wires are custom built to suit customers actual requirement. These wire are normally supplied as Annealed finish wires APPLICATION : Used in manufacturing of lock circlip used for locking shafts Specification : IS:EN 42C/42J
DESCRIPTION : It is galvanised steel barbed wire with two strands of wire used for fencing. APPLICATION : Used in fencing Type A : The wire have four points and formed by twesting two points wire, each two turns, tightly around both line wires. Specification : IS:278 SIZE RANGE : All Sizes Material : The galvanised barbed wire is manufactured from galvaised mild steel wire confirming to IS : 280 Galvanizing : The barbed wire is galvanised and the galvanizing requirements as laid down for medium coated wire of IS:4826 specification for galvanised coating on round wire. Packing: The coils are normally supplied in bare condition.
DESCRIPTION : These wires are supplied in coils with Phosphated coating to facilitate cold heading operation. APPLICATION : Used in manufacturing Balls, Rollers, Taper rollers, Cylindrical rollers and needles etc. made out from EN31 / SAE 52100. SPECIFICATIONS : Grade EN31 / SAE 52100 (Carbon 0.98 â?? 1.10 % and Chromium 1.30 â?? 1.60%). Microstructure: Uniformly distributed fine carbide globules in ferrite matrix i.e. Spherodized annealed. All properties like Hardness, Tensile strength, Size tolerance, coil weight etc. are maintained as per customerâ??s specification. PACKING : The finished drawn wires are dipped in rust preventive oil, securely bound at four places and wrapped with Polethene & Hessian/ HDPE. We specialize in supplying Bearing wires to customerâ??s actual needs. Specification : IS:EN 31/SAE 52100 SIZE RANGE : Min. 1.60 MM, Max. 9.50 MM
DESCRIPTION : These wires are High Carbon Annealed Bright drawn wires. APPLICATION : Used in manufacturing hand sewing needle and Hosiery needle. SIZE RANGE : Min. 0.76 MM, Max. 2.00 MM
Electrical Wires And Cables And Also Non Ferrous Metals..Trading.
Metals ferrous and non ferrous, such as : aluminium ingots a7, copper cathodes 99.9% , copper milberry scrap 99.7%, hms 1&2, iron ore 62 64%, nickel wire etc., rapeseed oil, sunflower oil, corn oil, peanut oil, coal.