Battery crushing and hydro separation Battery crushing and segregation plants are required for handling of large volume of battery scrap to feed smelting units. In this automated system, batteries of all sizes are loaded on conveyor and fed into hammer mill. Batteries are crushed into small pieces and particles are collected at the bottom of hammer mill in a container. The container is already filled with water solution of specific gravity. The plastic material floats on the top of water solution and lead bearing scraps settles at the bottom in the container. The plastic is removed from the top with the help of water jet system. The bottom of container is fitted with screw conveyor for discharge outlet for lead bearing scrap. The lead bearing scrap is conveyed through screw conveyor to a vibrating screen, where large particles are retained and collected. They are further dried and used as raw material for smelting unit. The fine particles at the bottom of container are kept in agitation and after that passed through filter press to form a cake. This cake is further dried and used as a raw material for smelting unit. The plastic material is collected, washed further for processing. The portion of waste water is taken into treatment plant and similar amount is replaced with fresh water. There are very few battery crushing and hydro separation units installed with corporate groups. It is not viable for small and medium scale units because of high capital investment. Gradually parties are interested to install battery crushing and hydro separation units since it is mandatory to have same for import of used batteries in india.
Simi conductor
Tda
Remote digital indicator Accurate remote position indicator in range of 20 meters and above for dam & barrages. Any type of custum built equipment
Digital event counter - totaliser manufactured by fabrotech is useful as object or pulse counter in different process and industries. By setting a multiplying factor (0.00001 to 999999) it can be used for displaying the linear measurement such as total length in meters or cms. Input pulse can be from proximity switch, infra red sensor, voltage pulse or no-contact of a switch. It can be reset by front switch or from rear terminal. 6 digit 0.56÷height bright red led's display the count. Optionally this 6 digit counter can be used as low cost, compact 11 digit counter. In case of power failure, the display count is retained in memory without any battery. The power consumption is less than 5 watts. Operating supply voltage is 230 v ac + 10%, 50hz. Housed in enclosure of din size 48(h) x 96(w) x 110(d)mm. Each, 600gms, 96x48mm
RF components
PC Based Multiprocess Control System Trainer Sump tank, level tank, pressure vessel, temperature cabinet, pump, flow transmitter, level transmitter, pressure transmitter, temperature transmitter, pneumatic control valve, electropneumatic converter, data acquisition & control system along with graphical trend display, tunning parameter selection, p,p+i,p+i+d control, physical realization of parameters, turnkey system. Size:6'(l) x 1.5'(b) x 5.25'(h) Weight: approx.80 kg
PTC thermistor Used for over heat protection of various equipment & motors Available for switching temperatures from 60 deg c to 190 deg c PTCs in single, double and triple versions can be supplied Weight is approximately 5 gm per single piece The PTC thermistor has a diameter of 3 mm
We offer a wide range of Power Semiconductor devices.
Heat Sink available in Exrtruded or Bonded, Material - 6063 Customize product as per customer drawing
KELB15 is a precision programmable DC electronic load controlled by a high performance microprocessor. It uses 3.5-inch TFT true color LCD display offers 4 basic working modes (CC/CV/CR/CW) and 10 functional modes. With comprehensive protection, over-heat protection, over-current protection, over-power protection, over-voltage protection, loop oscillation protection. KELB15 series E-load supports RS232, LAN, USB and analog interfaces to fit your versatile solution and testing needs
KELB60 is a precision programmable DC electronic load controlled by a high performance microprocessor. It uses 3.5-inch TFT true color LCD display offers 4 basic working modes (CC/CV/CR/CW) and 10 functional modes. With comprehensive protection, over-heat protection, over-current protection, over-power protection, over-voltage protection, loop oscillation protection. KELB60 series E-load supports RS232, LAN, USB and analog interfaces to fit your versatile solution and testing needs
KELB180 is a precision programmable DC electronic load controlled by a high performance microprocessor. It uses 3.5-inch TFT true color LCD display Offers 4-basic working modes (CC/CV/CR/CW) and 10 functional modes. With comprehensive protection, over-heat protection, over-current protection, over-power protection, over-voltage protection, loop oscillation protection.KELB180 series E-load supports RS232, LAN, USB and analog interfaces to fit your versatile solution and testing needs.
Measurement of Magneto resistance of semiconductors - BRAND - VIJAYANTA, INDIA 1. Measurement of Magneto resistance of semiconductors, Model: MRX-01 The Apparatus consists of the following Unit : (a) Four Probe Arrangement (b) Sample : Ge Crystal n type (c) Magneto resistance Set Up, DMR 01 (d) Electromagnet (Flat Faced Poles) 50, mm Poles, 7.5 K Gauss at 1, cm Air-Gap., EMU-50 (e) Constant Current Power Supplies for Electromagnets 0 4, Amp. Suitable for EMU-50, CC-50 (f) Digital Gauss Meter (Range : 0 - 2 K Gauss , 0 - 20 K Gauss), DGM-100
Best online store for electronic components, military grade, aviation, Industrial spares and automation, semiconductors, medical boards, industrial boards and much more We are importers exporters stockiest dealers of all kinds of products and specialize in hard to find components. Contact us on sales@adatronix.com or visit our website at www.adatronix.com Please let us know if you have any requirements.
Digital Ammeter ( AC ) Single Phase 4 Digit , 7 Segment LED Display CT Selectable up to 2000/5 Amps 30.0 Amps direct
This kind of NTC Thermistor used in automotive engine temperature sensing with two wire type in different mechanical and electrical specifications as per customer spec. We can support all the needs as per request.
Disc NTC Thermistor type used in automobile engine temperature sensor assembly and widely using in globally for the automotive area engine temperature sensing. We can support your custom requirements and can support accordingly
Haj maulim is the device which works as a guide for all the muslim pilgrims going for haj or umra. There are 30 push buttons on the device assigned with specific prayer (in arabic) for haj/umra. Each prayer (dua) is preceded by a commentary in the native language where the product is sold. Commentary will explain the purpose of the prayer and when to recite it. By pressing the button you will hear the prayer with the commentary through the ear phone which will be provided with the device. We will also provide three 1.5 v batteries with the device and if that batteries are exhausted the user will have to buy new for its use or if he wants he can also use rechargeable batteries for longer usage. Features: 1. Commentary for each of the duas in native language. 2. Play and pause function. 3. Digital volume control via button press. 4. Low power consumption. So the battery lasts longer. 5. Very good voice quality. 6. Good looking and robust. 7. Low battery detection (optional) Contents: 1. Haj maulim device 2. Earphone 3. 3 aaa batteries 4. Neck string 5. User manual 200 pcs in one carton
1) basmati rice 1121 sella, 1509, 1401, 1718 2) non basmati rice ir 64 parboiled, sona masoori, swarna, brown rice, ponni, idli rice 3) all kinds of spices like red chilli powder, coriander powder, moringa powder, turmeric powder, masala powder, cardamom, cinnamon, and turmeric fingers. 4) refined sunflower oil, palm oil, coconut oil 5) aluminum ingots, copper cathodes, copper Millberry Scrap. 6) solar panels, lithium-ion batteries, inverters, lead acid batteries 7) icumsa 45, s30 sugar.
