Ahmedabad Wine Bar Set Suppliers and Manufacturers

FRP handrails can be used any type of typical handrail application for stair, platform / walkway or as guardrails. The typical FRP Handrail system uses FRP profiles as the pillar support body and is fixed together with a set of pipe connectors. There are certain common options available; it can also be customized as per user requirements. - Common options Square Tube guardrail - 50 mm square tube as top rail and post, 40 mm square tube as middle rail. Round Tube guardrail â?? 50 mm round tubes as top rail and post, 36 mm round tubes as middle rail. Combination of Square and Round tube guardrail is also possible. - Special FRP Fencing Fiber Glass gratings can also be used as fiberglass fencing system together with the pultruded profiles and fittings.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Ingredients: Almonds, peanuts, cashews, raisins, dried cranberries, honey, oats, chia seeds, flax seeds, natural flavours.

Ingredients: Yogurt-flavoured coating (sugar, palm kernel oil, nonfat dry milk solids, yogurt powder (cultured whey protein concentrate, cultured skim milk), soy lecithin (an emulsifier), lactic acid, natural flavour), almonds, dried cranberries, oats, honey, cashews, raisins, natural flavours.

Rock bolts are commonly used in civil engineering and mining to reinforce and stabilize rock masses. A rod or bar is inserted into a drilled hole, which is then grouted in place using cement or resin. FRP Rock bolts withstand tensile forces and evenly distribute load, eventually increasing overall strength. They control rock movements, reduce deformation and prevent collapses.

We supply top-grade EN590 Diesel fuel and high-quality Diesel D6, both meeting rigorous international standards. EN590 is ideal for all diesel engines, while Diesel D6 serves various industrial applications. We offer competitive pricing and CIF delivery terms. Significant discounts are available for bulk purchases, making our products a reliable and cost-effective choice for both retail and wholesale buyers.

Our premium-quality Silica Sand, sourced directly from Indonesia, is known for its high purity and uniform grain size. Ideal for various industrial applications, including glass manufacturing, foundries, and construction, our Silica Sand ensures consistent performance and meets stringent international standards. With large-scale supply capabilities, we cater to the specific needs of our global clientele.

Our premium manganese from South Africa is celebrated for its high purity and robust quality, making it essential for steel production and various industrial applications. Carefully mined and processed, our South African manganese guarantees superior performance and reliability, meeting the rigorous standards of the global market.

Our High-grade Iron Ore from South Africa is renowned for its exceptional purity and consistent quality, making it an ideal choice for steel production and various industrial applications. Meticulously extracted and processed, our iron ore ensures optimal performance and reliability in every use, meeting the stringent standards of the global market.

Experience the reliability of our Indonesian Steam Coal, sourced from South Kalimantan. Perfect for power generation and industrial uses, our steam coal offers consistent quality and high caloric value, ensuring efficient energy production.