Anti corrosion for securing the Iron,S S ,MS and iron base metal, this is basically rubbered based chemical which provides the protection to the iron.
Bowed spreader rolls, rubber bow roll, metal expander roll, teflon bow roll, wrinkle remving rolls, slat expander roll, scroll roll, polyband expander roll, rubber grooved roll, core holding device, air expanding shaft, air chucks, quick locks, web guiding systems, hydro pneumatic web aligner, tyrecord centralizer, pneumatic cloth guider, conveyor tracker, web handling equipments, safety chucks (square bar holder), static eliminator, anilox roll for flexo printing machine, liner-dot engraved roll, ink circulating pump with flameproof motor, turn bar system, rolls for web carrying, cooling rolls, hard chrome rolls, stainless steel rolls, aluminum rolls, rubber rolls, brush rolls, textile equipments & accessories, rubber curve bar expander roll, cloth guiders, curve bar expander, brush roll, selvedge uncurler, surface winder(batching machine).
Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,.
Rubber compound, rubber ring, rubber bush, di pipe rubber ring, PVC pipe rubber ring, rubber grommet, rubber profile, rubber molding parts, profile part.Manufacturing
Sodium silicate, sodium silicate lumps, sodium silicate cullet, sodium silicate glass, water glass, sodium silicate neutral, sodium silicate alkaline, sodium silicate neutral glass, sodium silicate liquid, sodium silicate powder, potassium silicate, potassium silicate glass, potassium silicate cullet, potassium silicate lumps, potassium silicate liquid, metasilicate.
Tile adhesives, polymer grout, industrial grout and other construction chemicals.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Fresh vegetables like onion, pomegranates, green chili and coconut, chemicals and dyes, automobile parts and garments..Export, sourcing agent
Food, agriculture, chemicals, construction material ,.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
Natural rubber RSS, latex 60%, plc, ISNR, rubber pigments, rubber chemicals, Copper bus bar, tube, rods (square, hax, round), solid earth rods, copper anodes, nuggets, copper alloy tubes, PVC coted tubes, washer, copper profile & section also electrolytic bus bar.
Rubber chemicals like treated sulphur, pre dispersed rubber chemicals like s 80, cao 80, one pack accelerator, nitrosamine free accelerator, calcium hydroxide, magnesium oxide, specialty processing promoters, desiccants, speciality rubber & plastic chemicals.Manufacturer
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
Diamino sulfanilide (dasa) diamino diphenylamine, sulphonic acid, diamino benzanilide(daba), vinyl sulphone, ester of acetanilide (para base vs), diamino diphenyl 2, 2' disulfonic acid (bdsa), vinyl sulphone ester of ortho anisidine base (oavs), p-amino phenyl azo salicylic acid ( papas acid), orthonitrotoluene parasulphonic acid (ontpsa).
Supplying business of construction chemicals like Tile Adhesive, Epoxy tile grout, Concrete admixtures, Bonding agent, Anchor grout, Epoxy floor coating, Water proofing, Rust remove coat, Sealers and cleaners etc...
Blast media for sand blasting & concrete raw material for construction companies.
Binders, Paint And Coating Binders, Carpet And Non Woven Binders, Tape Adhesive, Textile Auxillaries, Textile Polysol, Pigments And Khadi Binders, Flock Binders, Wood Adhesive, Waterproofing Binders, Coating Powders Like Titanium Dioxide, China Clay, Kaolin, Calcium Carbonate.
Potassium Silicate (solid) Lumps is available as per customer requirements and applications like As a flux binder in welding electrode Acid proof lining Detergents and soaps Phosphor binder in T.V. tubes Potassium Silicate liquid also available as per customer requirements and applications.
Natural Rubber, which is obtained predominantly from the rubber tree, Hevea Brasiliensis, is an aqueous colloid of rubber containing 30-40% rubber, by mass. Getting the rubber in a dry form is a specialized process in itself. The raw is concentrated, i.e., its % rubber content is increased and proportion of non-rubber constituents is reduced by processes such as centrifuging and creaming.
This major chemical has a bitter taste and finds application as a good additive in various food utensils, sodas and candies. It has a white crystalline powder texture and is also used as an acidifier. The citric acid orders are provided in safe containers that help retain its features for a long time. We undertake bulk orders of the acid easily. Features : Used as an acidifier Natural preservative and conservative White crystalline powder
