Refractory bricks, high alumina bricks, acid proof bricks, tiles and castables, all mortars and fire clay, low cement castables, insulating castables, conventional dense refractory bricks, insulation bricks, cold face, hot face insulation bricks, hot face insulation bricks, acid resistant bricks/components, membranes, acid resistant cement, construction chemicals, class 1 ar tiles and bricks 38mm and 75mm, 4457 vitrified ar tiles with 0% water absorption, 20mm & 25m, primer, mastics, pot. silicate cement, coerce cement, furnace based cement, crushed refractory boiler bed material, acid resistant tiles, acid resistant brick fireclay type, acid resistant brick red shale type, bitumen primer, epoxy resin & hardner, furan powder and syrup solution,.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Hdpe, lldpe, pp granules, sodium citrate, potassium citrate, calcium citrate, cow dung cake, forklift, vermiculite coated ceramic cloth, fire proof cloth, Welding blanket, Paper box, Paper container, Industrial chemical, Plastic bucket, Paper angle.
1. coco peat (coir pith), coir rugs, 2. textile chemicals, polysols, binders, thickeners and many other industrial chemicals, 3. sugar confectionary products like lollipop etc. 4. eco friendly, sugarcane and paper packaging products like coffee/tea cups, beverage cups all sizes, takeaway lunch boxes, straws, etc. 5. frozen indian snacks like samosa, patties, mix veggies, all kinds of indian snacks and frozen foods. 6. pvd coated sanitary ware like kitchen sinks, basins, railing, taps, and other furniture with elegant polishes of gold, rose gold, black, silver, multi color, champagne colour, etc in different textures. 7. dehydrated vegetable and fruit powders like, dehydrated garlic powder, ginger powder, chickoo powder, etc. 8. onions 9. all kinds of supermarket items .Export and import
Our products are available in various specifications like 72gsm, 100gsm, 110 gsm, 150gsm, 170gsm, 200gsm, 250gsm etc. Available in various size as per customer requirement in different colour like black, yellow, blue, silver/white, silver/blue, yellow/white, orange/blue etc.
INDO wagon covers provides perfect protection against dirt, dust and moisture. It also protects your valuable goods from blazing sun-light and rains. HDPE coated INDO wagon covers are made of woven polyethylene fabrics of high mesh count. With the thickness from 85 GSM up to 500 GSM these covers are tear-resistant, puncture and mild impact resistant. It's smooth surface also protects your valuable goods from scratches and other damages. Available in standard wagon sizes as per international standards. We also provide customized sizes as per customer requirements. High Tensile strength Tear and Puncture resistant High Impact resistant Outstanding UV and stress-cracking resistance Excellent chemical and Corrosion resistant Flexible and easy to install More than 7 years self-life
INDO brand truck & trailer covers provides perfect protection against dirt, dust and moisture. It also protects your valuable goods from blazing sun-light and rains. HDPE coated INDO truck covers are made of woven polyethylene fabrics of high mesh count. With the thickness above 150 GSM these covers are tear-resistant, puncture and mild impact resistant. Itâ??s smooth surface also protects your valuable goods from scratches and other damages. Available in standard truck and trailer sizes as per international standards. We also provide customized sizes as per customer requirements. High Tensile strength Tear and Puncture resistance High Impact resistance Outstanding UV and stress-cracking resistance Highly Durable, tear proof and mild impact proof More than 7 years self-life
Pvc leather cloth, pvc artificial leather, synthetic leather, pvc super clear sheeting, pvc coated paper .
Swimming pool tarps come in every size, including up to 100 square, which will cover any swimming pool. Grommets are easily used to tie the tarp into place to get the taut cover on your pool. It generally come in blue color with thickness of 300 GSM and made of 100% natural material. We also supply specialized Tarps to fabricate and make temporary pools above grounds. The material used for this tarp is generally puncture proof.
Plastic resins (PP,PS,PET,PC,PVC)
Ingredients: Yogurt-flavoured coating (sugar, palm kernel oil, nonfat dry milk solids, yogurt powder (cultured whey protein concentrate, cultured skim milk), soy lecithin (an emulsifier), lactic acid, natural flavour), almonds, dried cranberries, oats, honey, cashews, raisins, natural flavours.
Viscose and nylon flocking powder, nylon flock powder, nylon flocking powder, viscose flock powder, viscose flocking powder.
HDPE Raw Materials
LLDPE Raw Material
PP Granules
Sodium Citrate
Chiffon - Georgette - Satin - Cotton polyster blend available in different different counts in more than hundred colours.
Alum is a group of hydrated double sulfates of aluminum and other elements such as potassium or ammonium. It is widely used in water treatment, food processing, cosmetics, and pharmaceuticals. Below are the general specifications for different types of alum: Common Types of Alum: 1. Potassium Alum (KAl(SO)12O) - Used in water purification, food, and cosmetics 2. Ammonium Alum (NHAl(SO)12HO) - Used in industrial and water treatment applications 3. Sodium Alum (NaAl(SO)12HO) - Used in food processing and baking powder 4. Ferric Alum (FeAl(SO)12HO) - Used in water treatment and paper manufacturing Physical Properties: Appearance: White, transparent crystalline solid or powder Color: White or colorless (can be slightly yellow in ferric alum) Odor: Odorless Taste: Astringent and slightly sweet Solubility: Soluble in water, insoluble in alcohol pH (10% Solution): 3.0 - 4.0 Chemical Composition & Purity: AlO (Aluminum Oxide): 15-18% SO (Sulfate Content): 50-55% FeO (Iron Oxide) (For Non-Ferric Alum): Max 0.01% Water Insoluble Matter: Max 0.1% Moisture Content: Max 5% Purity: Min 99% Microbiological Standards (For Food & Cosmetic Grade Alum): Total Plate Count: Max 10,000 CFU/g Yeast & Mold: Max 100 CFU/g Coliforms:
