Ahmedabad Music Systems Cassette Players Suppliers and Manufacturers

* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

FRP handrails can be used any type of typical handrail application for stair, platform / walkway or as guardrails. The typical FRP Handrail system uses FRP profiles as the pillar support body and is fixed together with a set of pipe connectors. There are certain common options available; it can also be customized as per user requirements. - Common options Square Tube guardrail - 50 mm square tube as top rail and post, 40 mm square tube as middle rail. Round Tube guardrail â?? 50 mm round tubes as top rail and post, 36 mm round tubes as middle rail. Combination of Square and Round tube guardrail is also possible. - Special FRP Fencing Fiber Glass gratings can also be used as fiberglass fencing system together with the pultruded profiles and fittings.

FRP cable trays at INDO are manufactured from Glass Armored Thermoset fireretardant resins Available in different range applied for ideal locations where metallic systems get easily corroded INDO FRP Cable Tray system meet stringent Fire Retardant requirements It provides advantages like Anti Corrosion High Strength No Earthing UV Resistant Good Electrical Insulator Low thermal conductivity etc

Indian red chilli, a staple spice in Indian cuisine, is renowned globally for its rich flavor, vibrant color, and pungent heat. Cultivated primarily in the southern states like Andhra Pradesh, Karnataka, and Tamil Nadu, Indian red chilli holds a significant place in both domestic and international spice markets. The spice is available in various forms including whole, powder, and crushed flakes, each catering to diverse culinary needs. Specifications: Color: Bright red to deep red Flavor: Ranges from mildly pungent to extremely hot Capsaicin Content: Varies depending on the variety, affecting the heat level Moisture Content: Typically between 8-12% Shape: Long and slender to short and stout Seeds: Present in the inner pod, often removed in powder form to reduce bitterness Scoville Heat Units (SHU): Ranges from 30,000 to 100,000 SHU depending on the variety Ash Content: Maximum 8% Extraneous Matter: Maximum 1% Packaging: Available in 10kg, 20kg, 25kg bags, or custom packaging upon request Varieties: Guntur Sannam (S4 Type): Origin: Andhra Pradesh Characteristics: Bright red color, moderate heat, and pungent flavor SHU: 35,000 -40,000 Uses: Widely used in sauces, salsas, and as a powder in spice blends Byadgi: Origin: Karnataka Characteristics: Deep red color, less pungent, wrinkled appearance SHU: 15,000 - 25,000 Uses: Ideal for coloring in culinary preparations, used in the cosmetic industry for its natural dye Kashmiri: Origin: Jammu & Kashmir Characteristics: Bright red color, mild heat, smooth skin SHU: 1,000 - 2,000 Uses: Primarily for its color, used in tandoori dishes, and Indian curries Teja: Origin: Andhra Pradesh Characteristics: Extremely pungent, deep red color SHU: 50,000- 100,000 Uses: Hot sauces, pickles, and spicy culinary dishes Naga Chilli (Bhut Jolokia): Origin: North-East India Characteristics: One of the hottest chillies in the world, wrinkled skin SHU: 800,000 - 1,001,304 Uses: Specialty sauces, extreme heat lovers, and for creating hot blends Health Benefits: Indian red chilli is not only a key ingredient for flavoring but also offers numerous health benefits. It is rich in vitamins A, C, and E, and contains antioxidants which are beneficial for boosting the immune system. The capsaicin present in chillies is known for its anti-inflammatory properties, aiding in pain relief and weight management by boosting metabolism.