With our years of experience & in-depth knowledge in this field, we are engaged in offering a quality-assured array of Electric Thermic Fluid Heater. Details: A Thermic Fluid Heater (Thermal Oil Heater) is industrial heating equipment, used where only heat transfers are desired instead of pressure. In this equipment, thermic fluid is circulated in the entire system for heat transfers to the desired processes. Combustion process heats up the thermic fluid and this fluid carries and rejects heat to the desired fluid for concluding the processes. After rejecting it, this fluid comes back again to the thermic fluid heater and this cycle goes on. Arizon Thermal Systems offers Thermic Fluid Heater / Thermal Oil Heaters fired by extensive range of fuels. Thermic Fluid Heater / Thermal Oil Heaters are available in both solid fuel firing as well as LDO /GAS / DUAl fuel firing variants so that you get the advantage of economically available fuels. Four Pass Solid (Coal / Wood) Fuel Fired Thermic Fluid Heater: The Four Pass solid fuel (coal / wood) fired Thermic Fluid Heater comprises of two heat exchangers namely radiant pass heat exchanger & convective pass heat exchanger. Radiant pass heat exchanger is a coil with conical shape & highly graded insulating material on outer surface to resist heat loss. Convective pass is made of two parallel concentric helical coils designed for sufficient convective heat transfer. This set of coils is covered with shell & this shell is insulated to resist heat loss. Radiant and convective heat exchangers are connected by a specially designed refractory duct which allows flue gas to pass from radiant to convective zone. Complete unit consist of radiant coil, convective pass, Fire chamber with sufficient grate area, F.D. fan for forced combustion, Air pre-heater to retrieve tremendous amount of heat from flue gas and transfer it to combustion air, Multi-cyclone separator to separate ash particles from flue gas & I.D. fan to induce air from the system & pass it to chimney for exhaust. Features: Efficient Heat Transfer with optimum combustion Three Pass Design for LDO / GAS fired Three Pass as well as Four pass Design for solid fuel fired Reduced excess air with balanced Draft System 300°C at near atmospheric pressure Truly maintenance Free Easy access for inspection & cleaning Energy Efficient Fully automatic in operation, so no running attention required Application: Asphalt & Road construction Dyes, Chemicals and Intermediates Textiles & Process house Packing Petrochemicals & refineries Rubber product industries Wood / ply wood industry Pharmaceutical & drugs Food processing Ceramics Reactor vessel heating, Jacketed vessel heating, autoclave & tank heating
We are providing services like reconditioning of: Furnace crucible Induction melting furnace coil Water cooled cable Our special services : New matching furnace assembly (100kg -10000kg) suitable with existing power supply unit. A servicing and maintenance contracts for complete power supply with furnace assembly of all leading manufacturer of induction furnace supplier. Complete project consulting for buying of new induction furnace. We under take modification and repairs for old furnaces and bar heater coil box of heating equipments
Monoblock burner for all types of heating application like boiler, oven, hot air generator, dryer, furnace, melting furnace, heat treatment. Standard.
4-PASS Thermic Fluid Heater
3-PASS FULLY WET BACK STEAM BOILER Thermal-Max Steam Boiler Smoke tube type system boiler with three pass fully wet back design, suitable for cal / agro waste / oil / gas fuel. Salient Features: Factory-assembled horizontal package boiler. Less site work & quick commissioning Suitable for coal, wood & briquetted fuel. Manual firing - less complexity. Large integral furnace - minimum heat loss. High turn-down ration. End to end visibility of tubes. Easy access for inspection & cleaning. Quick and easy ash removal. Low excess air burners, imported / indigenous. Capacity:Oil Fired - 500 kg./hr. to 8000 kg./hr. Solid Fuel Fired - 500 kg./hr. to 6000 kg./hr. Pressure:10 kg./cm2 to 35kg./cm2
Fully Automatioc Coil Type Boiler Fully automatic, instant steam generating range of boilers designed for safe and reliable operations. Easy to install and commission, these time-tested boilers require very little maintenance. It features a specially designed furnace and combustion system to burn difficult heavy oils and offers fuel flexibility between light and heavy oils to help respond to fluctuating fuel prices. Salient Features: High Efficiency. Large Steam & Water Volumes. Less Maintenance Unique patented membrane design Built-in heat recovery device Membrane design allows large tube diameter for coil enabling better steam dryness, less frequent de-scaling, longer coil life and minimum downtime Unique economiser - optimiser design ensures maximum heat recovery without possibility of feed water pump failure due to boiling/ vapour causing cavitations and pump failure Unique circulation burner design prevents leakage and eliminates fire hazard Ceramic wool refractory allows fast cooling of top plate and easy maintenance Easy access to all parts requiring maintenance. Capacity:500 kg./hr. to 850 kg./hr. Pressure:10 kg/cm2 to 20kg/cm2 Fuel:Coal / Wood / Lignite / Petcock
Our steam pressure reducing station are pre-fabricated manufactured ready to install units for steam system management. The pre-assembled steam pressure reducing stations are individually sized to meet end-user's specific needs. lnlet and outlet piping & valve are sized as per best engineering practices. Each unit is custom engineered and designed to meet specific system requirements. All upstream & down stream pipe work & fittings are adequately sized to ensure that only the required pressure drop occurs across the control valve itself.
This is basically A heat transfer equipment to heat air prior to entering in the furnace with a primary object to increase thermal efficiency of hot flue gases are passed through the tubes and air outside the tubes. The heat of the boiler flue gas is recovered in APH to increase the air temperature & the thermal efficiency is increased. Another advantage is that the flue gas is sent to chimney stack at lower temperature allowing simplified design of ducting & flue gas stack. It also allow controls the temperature of flue gas leaving the stack to meet emissions regulation / pollution control. Salient Features: Easy installation Low maintenance cost Robust construction Compact High efficiency
Industrial Hot Water Generators are vented systems provide temperatures up to 98°C. Pressurized systems are essentially closed loop required for indirect heating and provide temperatures up to 150°C without boiling or steam formation. The system is suitable to heat water up to 250°C with combustion of any solid fuels like wood, coal, bagasse, corn cobs, agrowaste, lignite, petcoke, etc. System is designed with all safeties & controls well defined for safe operation without lesser maintenance. Salient Features: Heat transfer efficiency Long thermic fluid life Corrosion free No scale problems No boiler regulation High temperature Abrasion resistant Easy to use Capacity:600,000 to 10,000,000 kcal/hr. Temperature:upto 200°C Fuel:Coal / Wood / Lignite / Paddy Husk / Petcock / Saw Dust / Bagasse / etc
A unique design of the pre-furnace consists of lateral wall made of finned tube connected to the boiler body through headers. Salient Features: Complete gas-tight construction. Greater absorption of radiant heat. Fast water circulation resulting in accelerated start up and better boiler response to load fluctuations. Designed to give full load efficiency upto 80%. Optional FBC System for Capacity above 5000 kg./hr. for Automatic Firing. Capacity:1000 kg./hr. to 15000 kg./hr. Pressure:10kg./cm2 to 35 kg./cm2 Fuel:Coal / Wood / Lignite / Paddy Husk / Petcock / Saw Dust / Bagasse / Palm Oil Extracts / etc.
3-PASS FULLY WET BACK STEAM BOILER Thermal-Max Steam Boiler Smoke tube type system boiler with three pass fully wet back design, suitable for cal / agro waste / oil / gas fuel. Salient Features: Factory-assembled horizontal package boiler. Less site work & quick commissioning Suitable for coal, wood & briquetted fuel. Manual firing - less complexity. Large integral furnace - minimum heat loss. High turn-down ration. End to end visibility of tubes. Easy access for inspection & cleaning. Quick and easy ash removal. Low excess air burners, imported / indigenous. Capacity:Oil Fired - 500 kg./hr. to 8000 kg./hr. Solid Fuel Fired - 500 kg./hr. to 6000 kg./hr. Pressure:10 kg./cm2 to 35kg./cm2
Keeping in mind the precise demands of patrons .we offer a qualitative assortment of BOILER FIRE BAR. Our offered bar is extensively demanded by our customers to use boilers for its sturdy construction and high durability. Features Low Maintenance Precise Dimensions Fine Finish
We are One of the Leading Cross Pump to Boiler Fuel Cross Component Which is of Vital Importance to Any and Every Type of Boiler Application.Made Our of Gr.20 to With stand Temperature and Used in Fuel Transport line. Model : Fuel Cross Four Way Type : 4 to 6 Inch Material : CI Casting
Steam boilers, thermic fluid heaters & burners.
Burner.
Melting furnaces.
Heat treatment furnace.
Columns and furnace internals for refineries.
Furnace System.
Silica ramming mass.
