White Denatonium Benzoate Powder that we are presenting to extensively scattered patrons is one of the bitterest substances. Ideal to use for many different purposes, this type of substance is utilized for the denaturing of alcohol so as to make it undrinkable as well as ready for industrial usages. Procured from reputed dealers in the industry, the White Denatonium Benzoate Powder is free from impurities, long in shelf life and can easily be bought from us in needed amounts with safe packaging at market justified prices
low aromatic white spirit ( LAWS ), GUAR GUM ALL GRADES
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Raisins are dried grapes. The drying process concentrates both the nutrients and sugars present in grapes, making raisins nutrient-dense and calorie-dense.
Ingredients: Yogurt-flavoured coating (sugar, palm kernel oil, nonfat dry milk solids, yogurt powder (cultured whey protein concentrate, cultured skim milk), soy lecithin (an emulsifier), lactic acid, natural flavour), almonds, dried cranberries, oats, honey, cashews, raisins, natural flavours.
Honey is a natural sweet substance produced by bees from floral nectar. It is widely used in food, pharmaceuticals, cosmetics, and traditional medicine. Below are the general specifications for honey: Physical Properties: Appearance: Thick, viscous liquid or crystallized form Color: Light amber to dark brown (varies based on floral source) Odor & Taste: Pleasant, characteristic honey aroma and sweet taste Texture: Smooth, free from lumps or impurities Moisture Content: Max 18-20% Solubility: Completely soluble in warm water Chemical Properties: Fructose Content: 38-42% Glucose Content: 28-32% Sucrose Content: Max 5% Total Reducing Sugars (Fructose + Glucose): Min 65% Acidity: 0.2 - 0.5% (expressed as formic acid) Ash Content: Max 0.5% pH: 3.5 - 5.5 Hydroxymethylfurfural (HMF): Max 40 mg/kg (as per international standards) Diastase Activity (Amylase): Min 8 DN (Diastase Number) Proline Content: Min 180 mg/kg (indicator of natural honey) Microbiological Standards: Total Plate Count: Max 1,000 CFU/g Yeast & Mold: Max 200 CFU/g Coliforms: Absent E. Coli: Absent Salmonella: Absent Clostridium Botulinum: Absent Contaminants & Adulterants: Pesticide Residues: As per country-specific regulations (FSSAI, EU, FDA) Heavy Metals: Lead (Pb):
Alum is a group of hydrated double sulfates of aluminum and other elements such as potassium or ammonium. It is widely used in water treatment, food processing, cosmetics, and pharmaceuticals. Below are the general specifications for different types of alum: Common Types of Alum: 1. Potassium Alum (KAl(SO)12O) - Used in water purification, food, and cosmetics 2. Ammonium Alum (NHAl(SO)12HO) - Used in industrial and water treatment applications 3. Sodium Alum (NaAl(SO)12HO) - Used in food processing and baking powder 4. Ferric Alum (FeAl(SO)12HO) - Used in water treatment and paper manufacturing Physical Properties: Appearance: White, transparent crystalline solid or powder Color: White or colorless (can be slightly yellow in ferric alum) Odor: Odorless Taste: Astringent and slightly sweet Solubility: Soluble in water, insoluble in alcohol pH (10% Solution): 3.0 - 4.0 Chemical Composition & Purity: AlO (Aluminum Oxide): 15-18% SO (Sulfate Content): 50-55% FeO (Iron Oxide) (For Non-Ferric Alum): Max 0.01% Water Insoluble Matter: Max 0.1% Moisture Content: Max 5% Purity: Min 99% Microbiological Standards (For Food & Cosmetic Grade Alum): Total Plate Count: Max 10,000 CFU/g Yeast & Mold: Max 100 CFU/g Coliforms:
Alum powder is a fine, white crystalline powder derived from aluminum sulfate compounds. It is widely used in water purification, food processing cosmetics, pharmaceuticals, and industrial applications. Below are the general specifications for alum powder: Types of Alum Powder: 1. Potassium Alum Powder (KAl(SO)12HO) - Used in food, water treatment, and cosmetics 2. Ammonium Alum Powder (NHAl(SO)·12HO) - Used in industrial and textile applications 3. Sodium Alum Powder (NaAl(SO)12HO)-Used in baking powder and food processing 4. Ferric Alum Powder (FeAl(SO)12HO)- Used in water treatment and paper industries Physical Properties: Appearance: Fine, free-flowing powder Color: White or colorless (ferric alum may appear yellowish) Odor: Odorless Taste: Astringent and slightly sweet Mesh Size: 80-200 mesh (as per requirement) Solubility: Fully soluble in water Insoluble in alcohol pH (10% Solution): 3.0 - 4.5 Chemical Composition & Purity: AlO (Aluminum Oxide): 15-18% SO(Sulfate Content): 50-55% FeO (Iron Oxide) (For Non-Ferric Alum): Max 0.01% Water Insoluble Matter: Max 0.1% Moisture Content: Max 5% Purity: Min 99% Microbiological Standards (For Food & Cosmetic Grade Alum Powder): Total Plate Count: Max 10,000 CFU/g Yeast & Mold: Max 100 CFU/g Coliforms:
Bamboo salt is a traditional Korean salt made by roasting sea salt in bamboo tubes at high temperatures. It is known for its enhanced mineral content and health benefits. Below are the general specifications for bamboo salt: Physical Properties: Appearance: Fine or coarse crystalline powder Color: Light gray to dark gray (depending on roasting intensity) Odor & Taste: Slightly smoky, mineral-rich, salty taste Texture: Free-flowing, non-clumped, uniform granules Mesh Size: Fine: 80-120 mesh Coarse: 2-5 mm Solubility: Fully soluble in water Chemical Composition & Nutritional Properties (Per 100g): Sodium Chloride (NaCl): 85-95% Moisture Content: Max 1-3% pH Level: 9-12 (alkaline) Essential Minerals: Magnesium (Mg): 100-500 mg Calcium (Ca): 50-300 mg Potassium (K): 100-600 mg Zinc (Zn): 2-10 mg Iron (Fe): 1-5 mg Sulfur (S): Present in trace amounts Microbiological Standards: Total Plate Count: Max 10,000 CFU/g Yeast & Mold: Max 500 CFU/g Coliforms:
Aloe vera powder is a fine, dehydrated form of aloe vera extract, derived from the inner gel or whole leaf of the Aloe barbadensis miller plant. It is widely used in the food, pharmaceutical, cosmetic, and nutraceutical industries due to its rich bioactive compounds and health benefits. Below are the general specifications for aloe vera powder: Physical Properties: Appearance: Fine, free-flowing powder Color: Off-white to light beige Odor: Mild, characteristic of aloe vera Taste: Slightly bitter Mesh Size: 80-200 mesh Solubility: Water-soluble (spray-dried aloe vera powder) Partially soluble (freeze-dried aloe vera powder) pH (1% Solution): 4.0 - 5.5 Chemical & Nutritional Composition (Per 100g): Moisture Content: Max 5% Polysaccharides (Acemannan): 10-30% (varies by quality) Aloin Content (For Non-Decolorized Powder):
Hand Sanatizer liquid and bottles and other chemicals.
Alcohol hand sanitizer.
Skincare, haircare, makeup, IBA cosmetics.Marketing
SR.NO. DESCRIPTION UNIT RESULT 1 Appearance Wax 2 Density @ 80 C g/ml 0.872 3 Acid Value mg KOH/g 5.0 Maximum 4 Saponification Value mg KOH/g 10 Maximum 5 Melting Point C 45 C 6 Loss on Drying % 1% Maximum 7 Residue on Ignition % 0.5% Maximum 8 CholestrolContent 5.0 Minimum 9 Viscosity @ 80 C mm2/s 21.4 mm2/s Note: Variation in parameters: 5% +/ will be accepted by buyer. Parameters may change due to changing of Raw Materials. Result will be remain same
SR.NO. DESCRIPTION UNIT RESULT 1 Appearance Wax 2 Density @ 80 C g/ml 0.872 3 Acid Value mg KOH/g 5.0 Maximum 4 Saponification Value mg KOH/g 10 Maximum 5 Melting Point C 60 C 6 Loss on Drying % 1% Maximum 7 Residue on Ignition % 0.5% Maximum 8 CholestrolContent 5.0 Minimum 9 Viscosity @ 80 C mm2/s 21.4 mm2/s Note: Variation in parameters: 5% +/ will be accepted by buyer. Parameters may change due to changing of Raw Materials. Result will be remain same.
Lanolin Alcohol Crude INCI name: Lanolin Alcohol CAS no: 8027-33-6 EINECS No. 232-430-1 Synonyms: Woolwax alcohols, Wool Alcohols Description Lanolin alcohol crude is the unsaponifiable fraction of lanolin, composed of complex mixture of aliphatic alcohols (normal, branched iso, branched anteiso, structured diols) with a mean molecular weight of approximately 370. It is produced by alkaline, hydrolysis of lanolin feedstock. Lanolin alcohol Crude is a browny waxy solid in appearence. Recycled Lanolin Alcohol Crude is an ideal feedstock for Biofuel for firing boilers and burners to produce green electricity Composition Lanolin Alcohol Mixed: more than 95% Water & Impurity: less than 1% Specification Krishna Petrochemicals Acid Value, mg KOH/g: 5.0 maximum Saponification Value, mg KOH/g: 10 maximum Melting Point, C: 45 (Light Alcohol) 60 (Heavy Alcohol) Loss on Drying, %: 1.0 maximum Residue on Ignition, %: 0.5 maximum Cholesterol Content: 5.0 minimum Uses of Lanolin Alcohol: Cosmetics/Toiletries: Hand creams Moisturizers Protective creams Self-tanners Sunscreens Glossy lipsticks Makeup removers Foundations, powders Eye makeup Hairspray Shaving creams Baby oils, diaper lotions Industrial: Printing ink Furniture and shoe polishers Textile finishers Lubricants Cutting fluids Paper Conditioner Leather Other Uses: Emulsifier Can be converted to acelytaed lanolin alcohol Refined into lighter color lanolin alcohol Blended for absorbtion bases
Fruit pulp, fruit blends, fruit powder.Exporter
As per international standard, or as per particular specification given by bulk buyer too. 20kg net or 25kg net multi wall paper bag export worthy.
Denatured ethyl alcohol, hand sanitizer, chafing fuel gel, home care product.Manufacturer
Mango pulp, mango concentrate, mango puree, fruit pulp, guar gum, guar korma meal, guar meal, guar gum powder, dehydrated onion, dehydrated garlic, raw cashew nut, cashews.
