Advantage: Heated by 1800C Molybdenum Disilicide (MoSi2) heating elements, Alumina tube size (Outer Diameter): 60mm, 80mm, 100mm, 51 steps programmable temperature control, Furnace can be vacuumed or filled with protection gas GSL1700 Tube furnace is advanced type of GSL-1600. It's heater by 1800C MoSi2 heating elements. This furnace is widely used in Material and Chemical laboratory used for heating all kinds new samples at vacuum or gas protection environment. Temperature is controlled by high accuracy controller which can reach to +/-1C, and it can set 51 steps temperature program. The highest working temperature of this furnace is 1750C. Furnace Tube High Purity Alumina Tube Sizes of Furnace Tube ID: 50mm / OD: 60 mmá x 1000 mm long Heating Elements á6 PCS 1800C á MOSI2 MAX. Temperature 1700C Working Temperature 1600C Temperature Control PID Auto Control, 51Steps Program The Fastest Heating Rate 10C / min Heating Zone Length á457 mm ( 18") Constant Temperature Zone 150 mmá (6") Temperature Accuracyá +/-1C Voltage single, 220V AC, 50/60 Hz Power Max. 5KW Size 550 L x450 W x670 Há mm Net Weight 150 kg ( 330 lbs ) Package Size á47" x 45"x 45"(1200L x 1150W x 1150Hmm) . In wooden box.
1. High-quality heat source Under common-pressure liquid, the oil transfer heating system can output hot oil of maximum 350 fª for the heat user; Our heat-conducting oil heating systems applied the Fuji temperature control instrument and the intelligent self-tuning temperature control technology. The control precision is about f+ 1 fª and accurately control in the range of the used temperature; the main power for the heating used the solid-state modules non-contact switch circuit in order to adapt to the frequent switching and have no interference to the power supply. Dry combustion can also be avoided. The hot oil cooling system can be designed according to the end userf+s requirement, so that it can satisfy the process requirement of rapid cooling after heating up; 2. To save energy and low operating costs Heat-conducting oil heating system is the liquid phase closed cycle. The temperature difference between the output oil temperature and the return oil temperature is 20-30 fª, that is only to heat a temperature difference of 20-30 fª can the working temperature be reached. Meanwhile, no water treatment equipment is required for this device. No lose of steam runningf= steam reekingf=steam dropping and steam leakage as the steam boiler. The utilization ratio of heat is very high. It can save about 30% energy compared with the steam boiler. 3. Low Equipment Investment Due to the reason that the system of the heat-conducting is simplef=no water treatment equipment and more auxiliary equipmentf=low pressure bore by the boilers etc., the investment for the whole system is comparatively low; 4. Safety Because the system only withstands the pump pressure and there is no explosion risk for the heat conduction oil heating system, it is more secured; 5. Environmental Protection The environmental effect of the organic heat carrier heating system is mainly reflected in the minimal fume emissions, no sewage pollution and no thermal pollution; 6. Widely Application It can be applied in the following areas: by high-temperature shapingf= plate heatingf= rubberf= dryingf= dyeing and printingf= chemical industryf= plywood productionf=rolled water-proof material productionf= asphalt heatingf=non-woven hot-rolled machine, fiber glass press machinef= reaction kettlef= mould f=drying roomf= oven and other heating required industries. In wooden cases
1. High-quality heat source Under common-pressure liquid, the oil transfer heating system can output hot oil of maximum 350 celsius degree for the heat user; our heat-conducting oil heating systems applied the fuji temperature control instrument and the intelligent self-tuning temperature control technology. The control precision is about ía 1 celsius degree and accurately control in the range of the used temperature; the main power for the heating used the solid-state modules non-contact switch circuit in order to adapt to the frequent switching and have no interference to the power supply. Dry combustion can also be avoided. The hot oil cooling system can be designed according to the end user requirement, so that it can satisfy the process requirement of rapid cooling after heating up; 2. To save energy and low operating costs Heat-conducting oil heating system is the liquid phase closed cycle. The temperature difference between the output oil temperature and the return oil temperature is 20-30 celsius degree, that is only to heat a temperature difference of 20-30 celsius degree can the working temperature be reached. Meanwhile, no water treatment equipment is required for this device. No lose of steam running, steam reeking, steam dropping and steam leakage as the steam boiler. The utilization ratio of heat is very high. It can save about 30% energy compared with the steam boiler. 3. Low equipment investment Due to the reason that the system of the heat-conducting is simple, no water treatment equipment and more auxiliary equipment , low pressure bore by the boilers etc., the investment for the whole system is comparatively low; 4. Safety Because the system only withstands the pump pressure and there is no explosion risk for the heat conduction oil heating system, it is more secured; 5. Environmental protection The environmental effect of the organic heat carrier heating system is mainly reflected in the minimal fume emissions, no sewage pollution and no thermal pollution;
1. High-quality heat source Under common-pressure liquid, the oil transfer heating system can output hot oil of maximum 350 celsius degree for the heat user; our heat-conducting oil heating systems applied the fuji temperature control instrument and the intelligent self-tuning temperature control technology. The control precision is about ía 1 celsius degree and accurately control in the range of the used temperature; the main power for the heating used the solid-state modules non-contact switch circuit in order to adapt to the frequent switching and have no interference to the power supply. Dry combustion can also be avoided. The hot oil cooling system can be designed according to the end user requirement, so that it can satisfy the process requirement of rapid cooling after heating up; 2. To save energy and low operating costs Heat-conducting oil heating system is the liquid phase closed cycle. The temperature difference between the output oil temperature and the return oil temperature is 20-30 celsius degree, that is only to heat a temperature difference of 20-30 celsius degree can the working temperature be reached. Meanwhile, no water treatment equipment is required for this device. No lose of steam running, steam reeking, steam dropping and steam leakage as the steam boiler. The utilization ratio of heat is very high. It can save about 30% energy compared with the steam boiler. 3. Low equipment investment Due to the reason that the system of the heat-conducting is simple, no water treatment equipment and more auxiliary equipment , low pressure bore by the boilers etc., the investment for the whole system is comparatively low; 4. Safety Because the system only withstands the pump pressure and there is no explosion risk for the heat conduction oil heating system, it is more secured; 5. Environmental protection The environmental effect of the organic heat carrier heating system is mainly reflected in the minimal fume emissions, no sewage pollution and no thermal pollution;
Vacuum cleaning furnace was used for cleaning the ordinary spinning plates, abnormal shaped spinneret plate, fine denier board, component housing for the terylene, polypropylene fiber, non-woven fabrics etc. Of the chemical fiber cleaning industry. It can also be used for washing the filter elements. It applied the principle that the synthetic polymer decomposed under the condition that isolating from the air in the vacuum state and the high temperature around 500 celsius degree. It owns the advantages of little environmental pollution, perfect cleaning of the spinning board, smoothed nozzle hole, extension the life of the spinneret board as well as shorter working hours, energy saving, easy to operate, good washing effect and high degree of automation etc. It is the updated products for replacing the triethylene glycol cleaning furnace and salt-bath furnace. Vacuum cleaning furnace is also applicable to the cleaning of the die-head and filter elements in the plastic industry.
Heating furnace.
1. Shaft furnace holding furnace up and down launder feeding device hydraulic transmission unit of holding furnace. 2. Shaft furnace holding furnace premixed burner of up and down launder include the control system multistage pressure blower system on-line automatic sampling controlled by plc co continuous automatic detecting system. Melting speed:6-20t/h Start time of melting:
Technical code 1. Melting furnace Upright cupola 2. Melting speed of copper plate 8-16t/h 3. Time of starting melt 2h 4. Material feeding mode Skip bucket style 5. Capacity of material feeding lifter 3t 6. type of heat retaining furnace hydraulic incline and action type 7. Effective volume of heat retaining furnace 6-10t 8. Max. incline and action angle of heat retaining furnace ¬â70 íµ 9. Oxygen consumed amount of copper furnace (copper bar per ton at normal production NG:50-70m3 LPG:40-60kg 10. shaft furnace and inner line of holding furnace All use sic molding brick 11. up and low flow slot Closed style integrated flow slot 12. fuel to be used NG/LPG 13. Diameter of gas supply NG:DN100-150/LPG:DN80-100.
aluminum heatsink(DP-1 industy heatsink) Application for: Intel LGA 775 1U Server Technical Parameter: Overall Dimension 240.5X154X8mm Heatsink Material: Al Panel + 5pcs Heatpipes Weight: 748g Main Process: Industry packing.
Heat sink extrusion(dp-2 industry heatsink) Application for: Surface treatment: anodized black Technical parameter: Overall dimension 229x218x18mm Heatsink material: Al panel + copper core Weight: 1142g Main process: Industry packing
OEM heatsink(DP-6 Industrial Heatsink) Technical Parameter: Overall Dimension 125X95X23mm Heatsink Material: Weight: 172g Main Process: industry packing
Extruded aluminum heatsink (DP-7 Industrial Heatsink) We are CPU radiator manufacturer , can supply you all kinds of CPU cooling systerm .We also can supply you the OEM raditor and ODM services.
Introduction: Psa nitrogen making machine is a new type of air separate equipment, taking the compressed air as raw material, taking the carbon molecular sieve as the sorbent, and adopting the transformation adsorption technique to produce nitrogen. Under the normal temperature and high pressure environment, it uses the different diffusing speed of nitrogen and oxygen in the carbon molecular sieve, separating nitrogen and oxygen. And the purity of nitrogen and the output can be adjusted based on customerí»s requirements. Usage: 1íómetal heating treatment: nitrogen protection bright annealed, metal powder sintering nitrogen protection, gas carburizing quench, etc. 2íóchemical industryú¦mainly used for protection air, replacement air and washing air to ensure safety of production. 3íóelectron industryú¦used for producing electron part and protecting production line. 4íófood industryú¦using nitrogen protection storage vegetables, fruits, seeds and tea, etc. 5íómedical industryú¦packaging the nitrogen into medicine to storage and transportation. 6íóother industryú¦eg. The nitrogen protecting in the floats law glass production line. Main technical parameter and collocation Type:jtpsa-n Output:5í½1000nm3/h Pressure:0.6í½0.8mp Dew point after purified:-40í½-65íµ Purity:99.99%
Item no.: Tst020 Size : D50*h81cm Weight : 60kgs. Packing wooden crate(cm) 54*53*h71(ctn)cm. Capacity 132/20.
Coal fired steam boiler: 1, Grate design type, include moving grate boiler, fix grate boiler, step grate boiler 2, Larger power boiler, circulation fluid bed steam boiler 3, From 0.5-80mw, pressure up to 100bar. Suited for exported shipment.
We have the exclusive patent products, research and produce the semiconductor key equipments. The outstanding advantage of its production is to take some techniques such as the plc auto-controlling system, independent innovating hot zone, magnetism liquid seal, power factor compensation and harmonic wave restraining and so on, which realizes the constant temperature of the hot zone, meets steady, continuous, high-efficiency, auto-controlling, non-dislocation and low oxygen and carbon requirements for dia.6inch--dia.8inch single silicon ingot. The products are high-efficiency, economize on energy, environmental protection and automatization , has the perfect foreground. Cz-80a, cz-90ai, cz-110
We have the exclusive patent products, research and produce the semiconductor key equipments. The outstanding advantage of its production is to take some techniques such as the plc auto-controlling system, independent innovating hot zone, magnetism liquid seal, power factor compensation and harmonic wave restraining and so on, which realizes the constant temperature of the hot zone, meets steady, continuous, high-efficiency, auto-controlling, non-dislocation and low oxygen and carbon requirements for dia.6inch--dia.8inch single silicon ingot. The products are high-efficiency, economize on energy, environmental protection and automatization , has the perfect foreground. Cz-80a Cz-90ai Cz-110
This boiler is "d" type water-tube steam boiler(hot water boiler): 1, d type design boiler(steam boiler and hot water boiler) 2, water-tube boiler design 3, steam boiler from 2mw-60mw, boiler pressure from 10bar-65bar 4, wide range of fuels: solid fuel(coal, wood), gas, oil and waste heat, or dual fuel options. 5, safe, efficient and durable water-tube boiler plant comprehensively engineered into an attractive package. 6, long-distance control boiler running, boiler can be protected auto, feed water auto, pressure control auto Suited for exported machine
This is 10ton steam boiler runing local: Steam output:10000 kgs/hr Steam pressure:17 bar Steam tempreture: 217 c Design standard: iso9001-2000 and as1228 Type: d type water pipe wall Safety, high effect , low noise, auto protect, etc This type boiler capacity up to 60mw, pressure up to 60bar Suited for shipment
Steam boilers: 1.Advanced burner and the plc, long-distance control, protect auto, auto feed water, auto control pressure. Feul range: diesel oil, heavy oil, nature gas, city gas, dual fuel options. 2.Rated evaporation:500kgs-30000kgs, pressure 7- 25bar 3.Compact structure.Logical design.Highly effective 4.Safe burning condition, low gas blacness 5.Save investment.Easy installation and moving 6.Power oil conserving.24 hours working life.Low noise 7.We can made all kinds of boiler based inquire 8.Large water volumes and steam space combine and production of dry steam under normal operating conditions Suited for exported shipment
