Pet.Coke dry powder combustion system. Water content ¡â2.0% Finess:200mesh¡ã100% Ii) Pet.Coke powder consumption:28t/d Iii) Requirements for compressed air:0.7mpa, 10m©ø/min Dry compressed air:0.7mpa, flow rate 10m©ø/min(stable pressure and flow rate) Iv)15 kw power:service power 15kw
Borosilicate glass process equipments Our products are as follows: - Glass components 1.Spherical vessels up to 300 ltr. 2.Cylindrical vessel up to 400 ltr. 3.Pipe component up to 600 dn. 4.Heat exchanger coil type up to 600dn 5.Shell & tube type heat exchanger up to 600 dn. 6.Glass valve up to 150 dn 7.Jacketed glass reactors upto 100 ltr capacity Standard assemblies 1.Distillation assemblies over glr (glass line reactor) 2.Standard units viz. Reaction, fractional distillation & reaction distillation units.Upto 300 ltr. Capacity Designs with supply 1.Absorption systems for gases e.G. Hcl, cl2, so2, hbr, nh3, h2s etc. 2.Anhydrous hcl gas generator. 3.Shell & tube heat exchanger 4.Sodium hypochlorite production unit. 5.Sulphuric acid dilution unit. 6.Solvent recovery / continuous distillation unit. 7.Rotary evaporator. Know how with plant 1.Bromine recovery. 2.Nitric acid concentration. 3.Sulphuric acid concentration. Pollution abatement packages with saleable by products 1. Emission/dischargeby product 2. - hcl (gas)commercial hydrochloric acid 3. - cl2 (gas)sodium hypo chlorite solution 4. - so2 (gas)sodium sulfite/ sodium bisulfite solution 5. - inorganic bromidesliquid bromine 6. - hbr (gas)commercial hydrobromic acid 7. -h2s (gas) sodium sulfide/ sodium bisulfide solution 8. - bromine (vapour)liquid bromine Full range of ptfe teflon product & laboratory glassware. We now looking forward to get an opportunity to serve your esteemed organization & country and awaiting your valued inquiries. Assure you of our best of services at all times.
Glass products Our products are as follows: - Glass components 1.Spherical vessels up to 300 ltr. 2.Cylindrical vessel up to 400 ltr. 3.Pipe component up to 600 dn. 4.Heat exchanger coil type up to 600dn 5.Shell & tube type heat exchanger up to 600 dn. 6.Glass valve up to 150 dn 7.Jacketed glass reactors upto 100 ltr capacity Standard assemblies 1.Distillation assemblies over glr (glass line reactor) 2.Standard units viz. Reaction, fractional distillation & reaction distillation units.Upto 300 ltr. Capacity Designs with supply 1.Absorption systems for gases e.G. Hcl, cl2, so2, hbr, nh3, h2s etc. 2.Anhydrous hcl gas generator. 3.Shell & tube heat exchanger 4.Sodium hypochlorite production unit. 5.Sulphuric acid dilution unit. 6.Solvent recovery / continuous distillation unit. 7.Rotary evaporator. Know how with plant 1.Bromine recovery. 2.Nitric acid concentration. 3.Sulphuric acid concentration. Pollution abatement packages with saleable by products 1. Emission/dischargeby product 2. - hcl (gas)commercial hydrochloric acid 3. - cl2 (gas)sodium hypo chlorite solution 4. - so2 (gas)sodium sulfite/ sodium bisulfite solution 5. - inorganic bromidesliquid bromine 6. - hbr (gas)commercial hydrobromic acid 7. -h2s (gas) sodium sulfide/ sodium bisulfide solution 8. - bromine (vapour)liquid bromine Full range of ptfe teflon product & laboratory glassware.
Glass Microspheres Machine Glass Microspheres Producing Equipments We have more than twenty years experiments in glass microspheres fields. That give us lots of skills in equipment revolution. We offer design and manufacture of figuration stove of glass microspheres / beads for your factory. You can produce glass microsphers / beads in your own brand with our equipment and material supplying.
Glass microspheres machine We have more than twenty years experiments in glass microspheres fields. That give us lots of skills in equipment revolution. We offer design and manufacture of figuration stove of glass microspheres / beads for your factory. You can produce glass microsphers / beads in your own brand with our equipment and material supplying. -
Tempered Glass Quality Testing Equipment Function: Determining the resistance of glazing material to impact by the penetration method. Principle: The specimen is supported vertically in a steel frame and an impact shot bag is released from a pre-determined height to strike the specimen at the centre. The height is progressively increased until fracture occurs. Related Standards: AS/NZS 2208 Safety glazing materials in buildings Appendix D: Impact Test GB 15763.3 Safety glazing materials in building Part 3: Laminated glass Appendix C: Test device for the impact performance of shot bag ANSI Z97.1 Safety Glazing Materials Used in Buildings - Safety Performance Specifications and Methods of Test - Clause 5.1: Impact Test Apparatus: 1) Impact testing frame: Frame Size: 1900mm*1500mm*3570mm Samples Size: 1930mm*864mm Lift: Electric Release: Auto Maximum impact height: 1200mm (customized) Rubber Pad Width: 15mm Rubber Pad Thickness: 3mm Rubber Pad Hardness: Shore A50 2) Impact shot bag: Weight: 45kg ±0.1kg 46kg ±0.1kg Height: 330mm ± 13mm Max diameter: 250mm Leather thickness: 1.5mm Lead sand size: 2.5mm Customized: 25kg /48kg
Frame Size: 1900mm*1500mm*3570mm Samples Size: 1930mm*864mm Lift: Electric Release: Auto Maximum impact height: 1200mm (customized) Rubber Pad Width: 15mm Rubber Pad Thickness: 3mm Rubber Pad Hardness: Shore A50 Impact Shot Bag: Reinforced leather bag filled with chiller lead shot
Frame Size: 1900mm*1500mm*3570mm Samples Size: 1930mm*864mm Lift: Electric Release: Auto Maximum impact height: 1200mm (customized) Rubber Pad Width: 15mm Rubber Pad Thickness: 3mm Rubber Pad Hardness: Shore A50 Impact Shot Bag: Reinforced leather bag filled with chiller lead shot
As per ISI and BS Standard Standard lot size
The distance between the foot line of l-shaped wall and top surface of sidewall is short, which allows thinner batch feeding so that the batch can be melted more easily. It can also reduce fire and batch running at the charge end and hence energy can be saved and environment improved.With its high reliability and long service life span, the l-shaped suspended back wall serves as one of the essential measures for prolonging the whole furnace life. Main technical index: 1. Modulus width of suspended wall: 300mm; 2. Width of brick structure: 380mm; 3. Length of nose zone (doghouse): 1700-2300mm; 4. Service life: more than 10 years.
Tempered Glass Impact Strength Test Equipment Function: Determining the resistance of glazing material to impact by the penetration method. Principle: The specimen is supported vertically in a steel frame and an impact shot bag is released from a pre-determined height to strike the specimen at the centre. The height is progressively increased until fracture occurs. Related Standards: AS/NZS 2208 Safety glazing materials in buildings â?? Appendix D: Impact Test GB 15763.3 Safety glazing materials in building Part 3: Laminated glass â?? Appendix C: Test device for the impact performance of shot bag ANSI Z97.1 Safety Glazing Materials Used in Buildings - Safety Performance Specifications and Methods of Test - Clause 5.1: Impact Test Apparatus: 1) Impact testing frame: Frame Size: 1900mm*1500mm*3570mm Samples Size: 1930mm*864mm Lift: Electric Release: Auto Maximum impact height: 1200mm (customized) Rubber Pad Width: 15mm Rubber Pad Thickness: 3mm Rubber Pad Hardness: Shore A50 2) Impact shot bag: Weight: 45kg�±0.1kg 46kg�±0.1kg Height: 330mm �± 13mm Max diameter: 250mm Leather thickness: 1.5mm Lead sand size: 2.5mm Customized: 25kg /48kg
1.Fill the molecular sieve quickly and efficiently in speed of more than 200mm/sec. 2.The additive bin ensures the moisture proof of molecular sieve 3.Control the filling more precisely, saving the molecular sieve 4.This machine can carry out two-way molecular sieve filling simultaneously and control the filling amount
The top roller installed at the both sides of the tin bath can effectively control the width and thickness of the gross glass ribbon. The main technical index: 1. The thickness of glass sheet:1.0-25mm 2. The horizontal oscillative angle of head: 3. The accuracy of head's oscillative angle: 4. The speed of rotating coil of head: 10-1500m/h 5. The accuracy of coil-speed of head: 0.01% 6. The radial direction run-out should be no more than 0.2mm 7. The accuracy of head's pressed-depth: 0.1mm 8. The biggest depth for head (inside the bath): 2000mm 9. The longest distance of machine frame for lifting up and down: 100mm 10. The accuracy of machine frame for lifting up and down: 0.1mm 11. All the above index can be customer-designed.
Used in float glass and ultra clear patterned glass production line, it includes the shell of the annealing lehr, transmission, hot air circulation system, electric heating system and control system. The main technical index: 1. Suitable for gross ribbon width: 2000mm-5400mm; 2. Suitable for gross ribbon thickness: 1.5mm-20mm; 3. Linear speed of annealing lehr roller: 80-1500m/h (stepless speed variation) 4. Diameter of annealing lehr roller: 216mm-365mm.
It is applied to large size doghouse. A couple of chargers are linked together so as to reduce their distance. In this way, it can well solve the batch off-track problem and cancel the water drum in the middle of batch tank. The batch could be evenly charged and its operation is very stable and continuous. By absorbing the batch charger technology at home and abroad, our company has tried some innovation on the batch charger in terms of its shovel plate quality and structure, thus improved its high temperature resistance in production, working stability and continuity. There are two types of batch chargers, namely arc blanket charger and inclining blanket charger.
Insulating glass machine Insulating glass machine, insulating glass machines, insulating glass machinery, insulating glass line, insulating glass equipment, insulating glass equipments Shape glass low-e insulating glass production line Automatic control for low-e glass (2-brush treatment for low-e) Automatic adjust function for pressing with hydraulic compression Titling table with hydraulic pressure Monitor using system temperature/speed/production volume Mechanical trouble cheek Whole line control function with 1 monitor Technique parameter Max. Glass size 2500f¯3500mm Min. Glass size 300f¯500mm Glass thickness 3-50mm Thickness of washing glass up to 60mm Max.In washing section 12m/min Max.In accelerating 50m/min Brush 4pair(low-e) Power voltage 3p 41.5kw(380v)/50-60hz Size of line 25000f¯2560f¯3380mm Power rate 20.6kw Size of line 25000f¯2560f¯3380mm
Made of ss 304/316 with satin/mirror polishing.
Glass fittings Material:stainless 316 and stainless 304 surface finish : satin mirror shape Demension : center to center 250 , 220, 210, 204, 200, 150 mm Models : t250-x, t220-x , t210-x, t204-x, t200-x, t150-x T250-y, t250-v, t250-i.T250-v/2, t250-i/2 F250-x, f250-y.F250-v, f250-i.F250-v/2, f250-i/2, F220, f210, f204, f200, f150 Wooden carton or paper carton
Bottles and vials for injection, syrups, tablets, droppers, capsules.
Ampoules vials cartridges
