Non contact ultrasonic level switch is a kind of non-contact, high reliability, high cost performance, easy installation and maintenance of material level measuring instrument.It doesn't have to contact medium can meet the requirements of most of the material level measurement.Firing pulse and receives the pulse interval and the antenna to the surface of the measured medium is proportional to the distance, to calculate the distance on the surface of the antenna to the measured medium. Ultrasonic Level Sensor, As shown in Picture below, the ultrasonic sensor Tx transmits ultrasonic waves reflected after encountering an obstacle received by the ultrasonic sensor Rx calculates the distance d of the obstacle according to Time-Of-Flight (TOF):d = (C x t)/2
The Separated Liquid Flow Sensor A1MF can be used to detect high and low water levels, etc., and give a signal when the water level reaches a certain position. The Non contact Infrared Level Sensor is a device used to sense the level of liquid in a tank. There is a board in the plastic housing. When the liquid level rises, it drives the prism, level switch will output low voltage signal. When the liquid level falls, infrared level control will output high voltage signal. The photoelectric liquid level switch uses the principle of optical reflection to measure, the performance of level sensor will be affected when it is exposed to direct sunlight or other infrared interference. Adjust the mounting angle or use a hood to avoid it. The photoelectric liquid level switch has high precision, low price, high reliability and wide application environment, it is less affected by strong acid, alkali and viscosity.
The reliability of liquid tank level sensor FS-IR2016D is high. It is not affected by liquid corrosiveness, pressure, magnetism, temperature, etc., it is less affected by external factors and has strong stability. EPT sensor is a manufacturer of liquid level sensors with 16 years of experience. We can provide corresponding solutions for all kinds of electrical equipment and other scenarios that require liquid level detection. If your steam microwave oven needs water level control, please contact us, we can provide you with food grade, hygienic, high precision, high reliability liquid level sensor to solve problems such as scale and water wall hanging. FS-IR2016D optical water level sensor has no mechanical moving components and with high reliability. This hot selling product is small in size and low in cost. Its advantage is high liquid level control precision. And it can be installed from any direction. Its waterproofing standard is IP68. The sensor itself also satisfies RoHS requirements.
FS-IR02B series Water Liquid Single Point Level Sensor, the theory is infrared, it can totally replace traditional float level switch, it controls the level though output high or low voltage. When the detected level is in air, due to reflect of the prism,most of light will enter receiver LED, optical level sensor will output high voltage. When the detected level is in water, due to refraction of the liquid, just less of light enter receiver LED, optical level sensor will output low voltage.
The FS-IR2003D is a single point liquid level switch that can operate in high pressure, high temperature, and aggressive environments due to its stainless steel and glass construction. This level switch offers industrial supply voltages and outputs that can directly drive loads. This model has a wide operating voltage, which is from 5VDC to 24VDC. The output ways have two types, NPN and PNP. The sensor can detect the presence or absence of almost any liquid, and can be configured to output a high or low signal in either a wet or dry state. The microcontroller based Stainless Glass Range liquid level switches are solid state, incorporating an infra-red LED and phototransistor which are optically coupled by the tip when the sensor is in air. When the sensing tip is immersed in liquid, the infrared light escapes making the output change state. The sensor can detect the presence or absence of almost any liquid type; oil or water based. It is insensitive to ambient light and is not affected by foam when in air or by small bubbles when in liquid.
-transmitting frequency as high as 26ghz -non-contacting radar, no abrasion and contamination. -small-sized antenna for easy installation -shorter wave length, better reflection achieved on inclined solid surface -smaller dead zone, better results ensured even in cannikin measurement. -small beam angle and concentrated energy to avoid interferences. -hardly influenced by corrosion and foam -hardly influenced by changes of steam vapor, temperature and pressure -hardly impacted by heavy dust -high snr to ensure performance even under fluctuation -choice for solid media and media with low dielectric constant
SPECIFICATIONS PRODUCT TYPE ANL-8260-PCBA FREQUENCY 26GHz RANGE 10m/30m/70m/80m(option) RESOLUTION 1mm ACCURACY ±10mm HYSTERESIS ±5mm DEAD-ZONE 0.6m INTERVAL 1s, subject to parameters RESPONSE TIME 5s, subject to parameters BEAM ANGLE 8 ° POWER SUPPLY 16..36VDC(24VDC typical) SIGNAL OUTPUT 4..20mA, 2-wire/4-wire COMMUNICATION HART LOAD 500 FAILURE OUTPUT No change/22mA/20.5mA/4mA(option) DISPLAY & KEYBOARD 128*64dot graphic LCD, 4keys TEMPEARTURE -40. HUMIDITY 95%RH DIMENSION 75mm x 75mm x 100mm
Product Name: Fiber Bragg grating acceleration sensor Product model: XH-A01 Application scope: seismic exploration State monitoring of industrial rotating equipment Cable force monitoring of bridge Safety monitoring of coal mine vibration Structural vibration test of Civil Engineering technical parameter Center wavelength of grating 1528nm ~ 1568nm Grating reflectivity >85% Standard range + 10g Resolving power 0.3% F.S. measurement accuracy 1% F.S. Packaging form Stainless steel Installation method Welding / screw fixation Fiber optic joint FC / APC Shape size (long x wide x high) 72*54*37.5 mm (without base)
Product Name: fiber grating patch type strain sensor Product model: XH-S02 Application scope: Strain monitoring of large steel structure Strain monitoring of ships, tunnels and rail Surface strain monitoring of bridge dam technical parameter Center wavelength of grating 1528nm ~ 1568nm Grating reflectivity >85% Standard range + 1500 Resolving power
Product Name: Fiber Bragg grating displacement sensor Product model: XH-D01 Application scope: Gap measurement Displacement monitoring of dam body Soil subsidence, rock, mountain, slope monitoring, etc. technical parameter Center wavelength of grating 1528 ~ 1568nm Grating reflectivity >85% Standard range 10/20/50mm (customizable) Resolving power
Product Name: Fiber Bragg grating temperature sensor Product model: XHT01 Application scope: High voltage switch, high voltage busbar temperature measurement Cable joint temperature measurement Temperature measurement at the interface of copper and aluminum Dry type transformer temperature measurement Technical parameters: Center wavelength of grating 1528nm ~ 1568nm Grating reflectivity >85% Standard range -30 C ~ +150 C Thermometer resolution 0.1 degrees centigrade measurement accuracy 0.5 degrees centigrade Packaging form ceramics Installation method Surface bonding / binding Fiber optic joint FC / APC Shape size (long x wide x high) 28.5 x 4 x 3 mm
Fiber Bragg grating pressure sensor Product Name: Fiber Bragg grating pressure sensor Product model: XH-P03 Application scope: Pressure monitoring in oil and gas wells Seepage pressure monitoring of dam body
HM612 is a newest smart digital motion detector. This Smart digital detector offers a complete motion detector solution, with all electronic circuitry built into the detector housing. Only a power supply and power-switching components need to be added to make the entire motion switch, a timer is included. The series has versions which can include ambient light level and sensitivity adjustments.
Senba Pyroelectric Infrared Sensors with high sensitivity, low noise and reliable performance. We have our own research and development department, with international technology and Hybrid IC technique expertise developed more than 15 years. The goods come standard with enhanced immunity to RFI (Radio Frequency Interference) and 2.4G high frequency interference. Senba PIR sensor suppport delay time, sensitivity adjustable, lighting adjustable.
Senba Pyroelectric Infrared Sensors with high sensitivity, low noise and reliable performance. We have our own research and development department, with international technology and Hybrid IC technique expertise developed more than 15 years. The goods come standard with enhanced immunity to RFI (Radio Frequency Interference) and 2.4G high frequency interference. Senba PIR sensor suppport delay time, sensitivity adjustable, lighting adjustable.
Waterproof Dallas Maxim DS18B20 Stainless Steel Digital Temperature Sensor Probe 15m Description Of The Dallas Maxim DS18B20 Stainless Steel Digital Temperature Sensor Ampfort DS18b20 temperature detector probe adopts the brand-new and original DS18B20 temperature sensor chip, chinese brand chip , GX18B20 produced by Beijing Zhongke Galaxy Core Technology Co., Ltd. belong to scientific research technology resources of the Institute of microelectronics, Chinese Academy of Sciences if you have cost pressure. Each pin of chip is separated by heat shrinking tube to prevent the short circuit, and sealed inside for waterproof and damp-proof. Its direct "One line Bus" digital transmission greatly improves the anti-jamming capability of system, suitable for field temperature measurement in harsh environments. At the same time, it is sealed with a high thermal conductivity of sealing rubber strip, to ensure the temperature sensorâ??s high sensitivity, with a very tiny temperature delay. Its measured temperature range is from -55 to +125, in the range of -10~ +85, its accuracy is ±0.5. When testing it, need to connect the signal end (yellow line) of sensor to the Digital port of microcontroller, meanwhile, need to add a pull-up resistor on the Signal end, or else the test will fail. Features Of The Dallas Maxim DS18B20 Stainless Steel Digital Temperature Sensor * 3.0V ~ 5.5V power supply * 9 to 12 adjustable resolution * Wide temperature range of -55 ~ +125 * No external components, a unique single-bus interface * Red (VCC), yellow (DATA), green (GND) * Output leads: red (VCC), white (DATA), black (GND) * Every pin of the chip is sealed and separated by the heat shrink tube. Good for insulation and to prevent short circuit. 3 output lines, * * * * * * VCC/DATA/GND. The exterior is made of PVC plastic tube, which is safe, wear-resistant and waterproof. * The high quality 304 stainless steel probe, is resistant to high temperature, fast heat conduction and accurate reading. * The sensor has one unique number and the temperature acquisition device identifies the corresponding temperature sensor by number. * The field temperature is directly transmitted in the digital way of 1-Wire bus, no need the external components and greatly improves the system's anti-interference. Suitable for the harsh environments. Internal Wiring Diagram Of The Dallas Maxim DS18B20 Stainless Steel Digital Temperature Sensor DS18B20 26AWG Cable Power NTC Thermistor 15m Digital Temperature Sensor Probe 2 Pin 1 Soldering to black GND ; Pin 2 Soldering to white DQ ; Pin 3 Soldering to red VDD;
Surface Temperature Sensing Ring Lug NTC Thermistor 10K 3950 For Beauty Equipment I Description Of The Ring Lug NTC Thermistor 10K 3950 A Precision NTC thermistor temperature sensor with ring terminal lug and flexible lead wire for surface mounting applications.This range of temperature sensors is made with tin plated copper ring lug terminals for easy and secure surface mounting, available as standard for use with M4 & M6 studs. It has fast response and an interchangeable 10k thermistor element with excellent long term stability and accuracy. These temperature sensors can be bespoke manufactured with many options for terminal sizes, lead wires and thermistor elements also available in 2.252k, 5k, 30k, 50k & 100k Ampfort offers Surface Temperature Probe Assemblies suitable for a wide range of temperature sensing applications. If the dimensions and electrical characteristics on this product won't work for your requirements, please contact us for further assistance. II Features Of The Ring Lug NTC Thermistor 10K 3950 1k~500M NTC Thermistor 0.2~1 C Accuracy M4 & M6 or other special size Ring Lug Terminals 1 Metre PFA flexible lead and can be customized III Application Of The Ring Lug NTC Thermistor 10K 3950 Electric Motors HVAC Systems Volume OEM Production Serial number Material name Specifications / Models 2-1. LEAD WIRE UL4413 #26AWG 2C TS 300V BLACK 2-2. HOUSING RNB8-5M Copper nickel plated 2-3. EPOXY FILLING( NB-5 BLACK 2-4. THERMISTOR R25=10K±1% B25/50=3950K±1% V Specification Of The Ring Lug NTC Thermistor 10K 3950 Serial number Item Symbol Test Conditions Min. Nor. Max. Unit 3-1. Resistance At 25 R25 Ta=25±0.05 PT 0.1mw 9.9 10 10.1 3-2. B Constant B25/50 3910. 3950 3989.5 k 3-3. Thermal Dissipation Constant Ta=25±0. / 2 / mw/ 3-4. Thermal Time Constant (in water)
Epoxy Coated NTC Thermistor 30K 3950 Temperature Probe Chip For Auto Wire Harness I Selection Of The Epoxy Coated NTC Thermistor 30K 3950 Temperature Probe Chip Modifications are available to existing standard product packages, such as adding connectors or changing wire size or length, as well as offering special resistance-temperature (R-T) curves, R-T curve matching, and custom lead forming and bending to discrete thermistors. In addition, the following options and services are available. Complete custom sensor packages, including moisture resistant designs Custom resistance-temperature (R-T) characteristics Specialized resistance tolerance or temperature accuracy within specified temperature ranges Sensing element design for best long-term stability Rapid prototyping and quick-turn concept parts including 3D printed parts Prototype units using prototype tooling Reliability/validation testing options Fully designed, production-capable sensor and tooling III Material Lists Of The Epoxy Coated NTC Thermistor 30K 3950 Temperature Probe Chip NO Material Name Item/PN 2-1. Element R25=30K±10% B25/50=3950±1% 2-2. Coating Epoxy Resin (Black) 2-3. Lead Wire UL4411# 24AWG 2C 7*0.20mm 125 300V (Yellow) Diameter:1.4±0.05 * 2.9±0.1mm Meet SAEJ-1128 IV Electrical Performance Of The Epoxy Coated NTC Thermistor 30K 3950 Temperature Probe Chip NO Item Sign Test Conditions Min. Normal value Max. Unit 4-1. Resistance at 25 R25 Ta=25±0.05 PT 0.1mw 27.0 30.0 33.0 k 4-2. B Value B25/50 3910.5 3950 3989.5 k 4-3. Dissipation factor Ta=25±0.5 In still air 2 mw/ 4-4. Time constant Ta=25±0.5 In still air 7 sec 4-5. Operating temp.range / / -20 / +125 4-6 Insulation resistance / 100V DC 100 / / M 4-7. Withstand voltage test / 200V AC 5 / / Sec
Stainless Steel Housing Temperature Sensor Chip NTC Thermistor 50K 1% 3950 100MM I Description Of The Stainless Steel Housing Temperature Sensor Chip NTC Thermistor Ampfort offers Stainless probe assemblies suitable for a wide range of temperature sensing applications. If the dimensions and electrical characteristics on this product wonot work for your requirements, please contact us for further assistance. 1.Temperature probe features XH2.54-2P connector and 15.7 inch (40cm) in length. 2.Mainly used in air conditioner for monitoring temperature, has quick reaction speed. 3.Application : thermostatic controls, industrial systems, consumer products, thermometers, any thermally sensitive system. II Features Of The Stainless Steel Housing Temperature Sensor Chip NTC Thermistor Tight Tolerance Moisture Resistant PVC Insulated Zip Cord 105�°C Max Operating Temperature Food grade stainless steel housing Custom and standard machined metal housings available in brass, stainless steel, aluminum, and exotic alloys Global engineering support for custom design solutions UL rated assemblies mateirals for HVACR applications IV Materials information Of The Stainless Steel Housing Temperature Sensor Chip NTC Thermistor NO Material Name Item/PN Origin 2-1. Lead wire UL2651#26AWG*2C 105 300V White KL 2-2. Thermistor R25=50K±1% B25/50=3950K±1% MF58 SH 2-3. Epoxy Resin J105/J106B/J05X Black DB 2-4 Shell 5.0*25 Round Head Stainless steel shell XDL VIII Thermistor Thermistors are a type of resistor that acts as a temperature-sensing element, generally made of ceramic or polymer. Thermistors exhibit a large change in resistance proportional to a small change in temperature. Thermistors come in two common types: NTC (Negative Temperature Coefficient) thermistors In these thermistors resistance decreases as temperature rises. An NTC is commonly used as a temperature sensor, or in series with a circuit as an inrush current limiter. PTC (Positive Temperature Coefficient) thermistors â?? In these thermistors resistance increases as temperature rises. PTC thermistors are commonly installed in series with a circuit, and used to protect against overcurrent conditions, as resettable fuses.
UV sensor 120-277V AC/ 220-240V AC input, remote control setting, off/on and sterilization timer function 5.8GHz C-band microwave motion sensor, off/on control. Operating voltage: 220-240V AC, 50Hz.(EU version) 120-277V AC, 60Hz.(US version). Rated load: 200W @ 120V AC, (capacitive) 400W @ 200-277V AC, (capacitive). Stand-by power:
