The Primary current sensor uses the same sensor technology as the original Rogowski coil. The True RMS inductive sensor does not use magnetic materials. The opening of the sensor is electronically closed and external currents are electronically rejected. The accuracy, external current reject, and range of currents measured by the patented amp sensor substantially exceed the performance of the best clamp-on sensors. The key feature of the unit is the ability to leave it deployed on the line to record readings every 15 minutes for 90+ days. It easily attaches to the line with a standard insulating bar. Once on the line, it immediately begins to collect and record the primary current on the line. The Primary current sensor is equipped with a 433M wireless port for communicating the recorded data into the userâ??s PC. The data is downloaded through GF2018S PC-Link Software, which allows the user to download, view and query the data stored on the Primary current recorder. The housing of the Primary current sensor is made of ABS+PC and is built to operate safely, even in severe utility environments. It is resistant to shock, waterproof and resistant to flame. It also operates within a wide temperature range. The Primary current recorder has a screw insulation bar of installation, which allows it to hang on the line securely in all weather conditions. PC-Link Software is a user-friendly software interface that allows the user to download, view, graph and export data from the Primary current recorder into Microsoft Excel. The data directly transfers from the Primary current recorder into Excel through an 433M Port. PARAMETERS Basic parametersã?? Recording ammeter kit 3 wireless current sensors (GF2018A, GF2018B, GF2018C) 433 HHT(handheld terminal) or 433M wireless data reader(GF2018R) PC-LinkSoftware software(GF2018S) Carrying case Data recording interval 1min, 5min, 10min,15min, 30min; Time can be set from 1 second to 60 minutes Communication distance(wireless) Max 100m Communication 433M, 868M or 915M (option) Installation Installation with electricity; Disassemble with electricity Battery 3.6 volt lithium battery,9000mAh; Battery can be replaced Software requirements PC-Linksoftware & microsoft Excel Processor 100 MHz or higher (200 MHz or higher recommended) RAM 32 MB, 64M recommended Drive space 15 MB to load software, 10 MB of operating Space Use of position Outdoor or indoor Electrical parameters Range of operation Voltage 69kV,35kV,20KV, 10kV, 6kV, 0.38kV Current 0 to 400A; 0 to 800A; 0 to 1500A; 0 to 3500A; Sensor opening Up to 3.3 cm Resolution Amps 1 to 99.9A 0.1A 100 to 300A 1A Amps accuracy ±1% of reading plus 2 counts Frequency 60Hz (57-63 Hz) or 50Hz (47-53 Hz) models available Mechanical parameters Weight (kg) 0.48 Carrying case(kg) 6.5 Environmental conditions Operating temperature -40C to 60C
Plasma enhanced rotational PECVD system, BTF-1200C-R-PECVD Product descriptionï¼? The whole experimental cavity is in the glow generation region, uniform equivalent glow, this technology is a good solution to the traditional plasma work instability, In this way, the range and intensity of ionization is 100 times of that of the traditional PECVD, to the uneven accumulation of materials . Use a quartz tube of a special shape (thin middle between two ends) as a reaction chamber for chemical vapor deposition.The furnace tube can rotate 360 degrees, Quartz stopper on the inner wall of the tube can help stir-fry the powder material and sintered more evenly, and the furnace body can be tilted to the left and right at a large angle, which is convenient to feed in and out, and the inclined angle is adjustable from 0 to 35 degree. Widely used in the preparation of graphene at low temperature and the carbon coating experiment of powder material. Main parameter Furnace Max. Tem1200°C Heating zone length 440mm Constant zone length 200mm Tem. control PID automatic control with 30 steps programmableï¼?Operation interface is 7 "industrial control computer Tube Size Φ60*420+Φ100*360+Φ60*420mm Furnace body inclination angle 0~35°ï¼?adjustableï¼? Furnace tube rotation rate 3~13r/min PE source Signal frequency 13.56 MHz±0.005% Power output range 0-500W Max. reflection power 100W RF output interface 50 Ω, N-type, female Power stability â?¤5W Gas supply system High precision mass Flowmeterï¼?Range optionalï¼? Accuracy ±1.5% Response accuracy ±0.2% Response time Gas characteristicsï¼?1ï½?4sec Electrical characteristics ï¼?10sec Working pressure difference range 0.1ï½?0.5MPa Max. pressure 3MPa Connection Φ6mmDouble clasp stainless steel joint Vacuum unit KF25 series bellows and manual stopper valves Vacuum degree 10-1 pa The value can be displayed intuitively by the digital display vacuum tester
DESCRIPTION CS-106 Winshield is a specially formulated copolymer protective coating used in place of windows frames, glass, bathtub, plywood, plastic faced formwork, moulds prior to casting concrete, to ensure a clean release and protective purpose. FEATURES Do not corrode glass, plastic or equipment Minimize subjects cleaning Cost effective Apply on plywood, timber, steel, glass and plastic faced Non-staining, Non toxic, non hazardous Water-based and environmentally compatible
Position/Semaphore Indicator used in ABB/SIEMENS: Rated voltage DC/AC 98V~242V or DC/AC 24-60V Luminous intensity ﹥40 cd/� Power frequency withstand voltage 2kV/1min Insulation resistance �100MΩ Power dissipation �1W Operating temperature -15 to +50 Lifespan ﹥10 years Display function Working condition is indicated with red/green color and graphics (As customers option) Outline dimension: 37.5�37.5�62(mm)
Product Features1. Perfect self-examination function: wrong signal will not sent to the appliance when the safety curtain sensor fails2. Strong anti-interference ability: has good anti-interference ability to electromagnetic signal, strobe light, welding arc and surrounding light sources.3. Easy to install and adjustable, simple wiring and beautiful appearance in accordance with European design standards4. Surface mount technology for superior shock resistance.5. IEC61496-1/2 standard of Type 4 and has passed CE certification, Type 2, Type 4.6.Short reaction time (â?¤15ms), Safe and reliable.7. 30 * 30mm width and thickness, effectively reduce the installation space; safety curtain sensor is connected to the cable through the aviation plug connector, which enables accurate, quick and simply assemble, dismantle and wiring.8. All electronic components of this safety curtain sensor are produced by world-renowned brands.9. This safety curtain sensor is mainly used in forging machinery and hydraulic equipment.10. For the press where the slider can be stopped at any position of the stroke, it can realize full protection or cooperate with the cam switch to achieve the protection of the stroke between 30 degrees and 180 degrees.Selection DiagramWiring Diagram
The product is smoke detector, hereinafter called detector. With a unique structure design and an intelligent MCU to process photoelectronic signals, it is provided with dust-proof, mothproof and anti-light interference etc. functions, ensuring the detector stability from design. It reacts very quick to visible smoke released by smoldering fire and flaming fire, and suitable for fire alarm in house, factories, shopping malls, hotels, restaurants, office buildings, teaching buildings, banks, libraries, warehouses, etc.. Product Feature - Low-battery warning - Auto-Reset after trigger - Infrared Photoelectronic Sensor - Sound & Flash Alarm & LED indicating Alarm - SMT Manufacture Technology, Reliable Stability - Dust-proof, Mothproof and Anti White light interference Technical Parameter Power Supply :DC 2*1.5 AA Static current:
Overview Quick Details Type: Pressure Sensor Size: OEM Size Car Make: MAYBACH;MERCEDES-B ENZ;volkswagen OE NO.: 5149174AB 0061539728;0061531328;0041533028;0041533228;2E0906051A Place of Origin: Zhejiang, China (Mainland) Brand Name: ANT Auto Model Number: M-128 Warranty: 1 Years Product Name: Manifold Pressure Sensors 1OE NO.:: A0051535028 2OE NO.:: 0041533228 3OE NO.:: 2E0906051A 4OE NO.:: 5149174AB 5OE NO.:: 0051535028 6OE NO.:: 0041533028 7OE NO.:: 0061539728 8OE NO.:: 0061531328 9OE NO.:: EP9451-R3A SupplyAbility SupplyAbility: 50000 Piece/Pieces per Month Packaging & Delivery Packaging Details white box or bags or according to your request Port shanghai or ningbo Lead Time 7-15days
Overview Quick Details Type: Speed Sensor Size: OEM Size Car Make: Buick OE NO.: 1541232 Place of Origin: Zhejiang, China (Mainland) Brand Name: ANT Model Number: S-1082 Warranty: 1 Years Product Name: Speed Sensor 1OE NO.:: 1541232 Working Power Range: DC 9-16V MOQ: 10PCS OEM Order: Accept Shipping terms: DHL,Fedex,Ocean etc. Delivery time: 7-15 days SupplyAbility SupplyAbility: 100000 Piece/Pieces per Month Packaging & Delivery Packaging Details Neutral Package Port Ningbo Or Shanghai Lead Time 5-14days
Thermal gas mass flow meter is designed on the basis of thermal dispersion, and adopts method of constant differential temperature to measuring gas flow. It has advantages of small size, easy installation, high reliability and high accuracy, etc. The meter contains two platinum resistance temperature sensors. The thermal principle operates by monitoring the cooling effect of a gas stream as it passes over a heated sensor. Gas flowing through the sensing section passes over two sensors one of which is used conventionally as a temperature sensor, whilst the other is used as a heater. The temperature sensor monitors the actual process values whilst the heater is maintained at a constant differential temperature above this by varying the power consumed by the sensor. The greater the gas velocity, the greater the cooling effect and power required to maintain the differential temperature. The measured heater power is therefore a measure of the gas mass flow rate. The format of gas velocity and power is shown as below: â?¦â?¦(1) Where: is specific gravity of medium V is velocity K is balance coefficient Q is heater power Î? T is differential temperature The medium temperature range of meter is -40ï½?220. In the format (1), the specific gravity of medium is related to the density: â?¦â?¦(2) Where: is the medium density in working conditionkg/m3 Ï�n is the medium density in standard condition, 101.325kPa and 20 kg/m3 P is the pressure in working conditionkPa T is the temperature in working condition In the formats (1) and (2), there is a certain functional relationship between the velocity and pressure in working condition, medium density, the temperature in working condition. Due to the sensor temperature is always 30 higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter do not need to do temperature and pressure compensation in principle
Product name: S type force sensor Features: 1. Miniature s type tension load cells are small and it is easy to install them. 2. The load cells with fully sealed structure offer good water resistance and high dynamic frequency. 3. The load cells are made of stainless steel and provide robust construction. 4. The load cells utilize strain gauge technology and provide high dynamic frequency Applications: Miniature compression and tension load cells are mainly applied in tension and pressure testing instruments, automatic equipments, and testing fields, such as insertion force test instruments, riveting machine, welding machine, hot & cold lamination machine, feeling tester for keyboard switch, and etc. Technical specification: Rated output 2.0/3.0 ± 10% mv / v Zero balance ±2 % f.S. Non-linearity 0.05% f.S. Hysteresis 0.05% f.S. Repeatability 0.05% f.S. Creep (30min) 0.05% f.S. Temp. Effect on output 0.03% f.S. / 10ºc Temp. Effect on zero 0.03% f.S. / 10ºc Input impedance 385±5 Output impedance 350±3 Insulation resistance 5000m/100vdc Recommended excitation 5-10v Maximum excitation 15 v Compensated temp range - 10 ~ 60 ºc Operation temp range - 20 ~ 80ºc Safe overload 150% Ultimate overload 200 % Cable size 53m Wiring Red: + excitation black: - excitation Green: + signal white: - signal.
Product name: S type force sensors Features: 1. Miniature s type tension load cells are small and it is easy to install them. 2. The load cells with fully sealed structure offer good water resistance and high dynamic frequency. 3. The load cells are made of stainless steel and provide robust construction. 4. The load cells utilize strain gauge technology and provide high dynamic frequency Applications: Miniature compression and tension load cells are mainly applied in tension and pressure testing instruments, automatic equipments, and testing fields, such as insertion force test instruments, riveting machine, welding machine, hot & cold lamination machine, feeling tester for keyboard switch, and etc. Technical specification: Rated output 2.0 â± 10% mv / v Zero balance ±2 % f.S. Non-linearity 0.05% f.S. Hysteresis 0.05% f.S. Repeatability 0.05% f.S. Creep (30min) 0.05% f.S. Temp. Effect on output 0.03% f.S. / 10âºc Temp. Effect on zero 0.03% f.S. / 10âºc Input impedance 350â±5, Output impedance 350â±5, Insulation resistance 5000m, /100vdc Recommended excitation 5-10v Maximum excitation 15 v Compensated temp range - 10 ~ 60 âºc Operation temp range - 20 ~ 80âºc Safe overload 120% Ultimate overload 150 % Cable size Ã?4ã?3m Wiring Red: + excitation black: - excitation Green: + signal white: - signal.
Product Name: S type Force Sensors Features: 1. Miniature S type Tension Load Cells are small and it is easy to install them. 2. The load cells with fully sealed structure offer good water resistance and high dynamic frequency. 3. The load cells are made of stainless steel and provide robust construction. 4. The load cells utilize strain gauge technology and provide high dynamic frequency Applications: Miniature Compression and Tension Load Cells are mainly applied in tension and pressure testing instruments, automatic equipments, and testing fields, such as insertion force test instruments, riveting machine, welding machine, hot & cold lamination machine, feeling tester for keyboard switch, and etc. Technical Specification: Capacity 10~5000kg Rated output 2.0 ± 10% mV / V Zero balance ±2 % F.S. Non-linearity 0.03% F.S. Hysteresis 0.03% F.S. Repeatability 0.03% F.S. Creep (30min) 0.03% F.S. Temp. effect on output 0.025% F.S. / 10ºC Temp. effect on zero 0.025% F.S. / 10ºC Input impedance 350±5Ω Output impedance 350±5Ω Insulation resistance �5000MΩ/100VDC Recommended excitation 5-10V Maximum excitation 15 V Compensated temp range - 10 ~ 60 ºC Operation temp range - 20 ~ 80ºC Safe overload 120% Ultimate overload 150 % Cable size �5�3m Wiring Red: + Excitation Black: - Excitation Green: + Signal White: - Signal capacity A B C D M Weight 10/20/30/50/75KG 63.5 50.8 12.7 19 M8*1.25�1/4-28� 100/200/250/300/500KG 76.2 50.8 19.1 25.4 M12x1.75�1/2-20� 750/1000/1500KG 76.2 50.8 25.4 25.4 M12x1.75�1/2-20� 2000/3000/5000KG 108 76.2 25.4 25.4 M18x1.5�3/4-16�
Product Name: S type Force Sensors Features: 1. Miniature S type Tension Load Cells are small and it is easy to install them. 2. The load cells with fully sealed structure offer good water resistance and high dynamic frequency. 3. The load cells are made of stainless steel and provide robust construction. 4. The load cells utilize strain gauge technology and provide high dynamic frequency Applications: Miniature Compression and Tension Load Cells are mainly applied in tension and pressure testing instruments, automatic equipments, and testing fields, such as insertion force test instruments, riveting machine, welding machine, hot & cold lamination machine, feeling tester for keyboard switch, and etc. Technical Specification: Capacity 50kg,100kg,200kg,300kg,500kg Rated output 2.0mV / V Zero balance ± 2 % F.S. Non-linearity 0.1 % F.S. Hysteresis 0.1 % F.S. Repeatability 0.1 % F.S. Creep (30min) 0.1 % F.S. Temp. effect on output 0.05 % F.S. / 10ºC Temp. effect on zero 0.05 % F.S. / 10ºC Input impedance 1100±5Ω Output impedance 1050â±3î© Insulation Â?¥5000mî©/100vdc Recommended Excitation 10 V Maximum Excitation 20 V Compensated Temp Range - 10 ~ 60 ºc Operation Temp Range - 20 ~ 80âºc Safe Overload 150% F.S. Ultimate Overload 200 % F.S. Cable Size Ã?3ã?3m Wiring Connection Red: + Excitation Black: - Excitation Green: + Signal White: - Signal Range, Size, Thread Lb, Kg, A, B, C, Mm, Inch 250-150, 100-750, 70, 19, 80, M10*1.5, 1/2-20 2000-3000, 1000-1500, 70, 25, 80, M12*1.75, 1/2-20 5k-10k, 2000-5000, 108, 25, 95, M18*1.5, 3/4-16 20000, 10000, 175, 51, 130, M30*2, 11/4-12 40000, 20000, 190, 60, 160, M39*2, 11/4-12
Stick on flat surface of merchandises, cable tie for option. Main parameter: Sensor size: 22 x 14 x 12mm. Sensor type: micro switch. Spring cable length: extension length in maximum. LED alarm indication: optional. Plug type: RJ11.
Stick on curved surface of merchandises Main parameter: Sensor size: 34x23x7mm. Sensor type: micro switch Spring cable length: extension length in maximum Color: white / black LED alarm indication: no Plug type: RJ11
Stick on flat surface of merchandises, offer cable tie and MINI USB charging output Main parameter: Sensor size: 42x20x12mm. Sensor type: micro switch Spring cable length: extension length in maximum Color: white / black LED alarm indication: optional Plug type: RJ11 Accessory: magnetic base
Fix to camera by screws, offer cable tie and 2 RJ11 signal input/output socket Main parameter: Sensor size: 60x37x17mm. Sensor type: micro switch Spring cable: RJ-2D Color: white / black LED alarm indication: yes Signal input / output port: RJ11 Accessory: magnetic base
Stick on flat surface of merchandises, offer RJ11 charging output socket, invisible wire, suitable for wall surface display Main parameter: Sensor size: 52x34x19mm Sensor type: micro switch Signal output port: RJ11 at bottom Color: white / black LED alarm indication: yes Charging output port: RJ11 at side Accessory: magnetic base
For DSLR lens Main parameter: Sensor size: 21x17x7mm. Sensor type: contact Spring cable length: customized Color: white / black LED alarm indication: no Plug type: RJ11
Stick on flat surface of merchandises, sensor could rotate freely Main parameter: Sensor size: diameter 28 x 15mm. Sensor type: micro switch Spring cable length: extension length in maximum Color: white / black LED alarm indication: yes Plug type: RJ11
