We are one of the leading manufacturer of all types cts of any ratio. We manufacture both outdoor and indoor types. We manufacture both resin cast & oil cooled cts As per mutual discussion
With high efficiency, low inrush current and low noise characteristics which are popular in the market. We also make reactor inductor for inverter of solar power with low loss and low noise. Power range 1000va to 30kva Phase single/three phase Input/output customized Insulation class ul class b, f, h, n (optional Isolation 4kv hi-pot
With high efficiency low inrush current and low temperature rise characteristics which are popular in the market. The transformer efficiency is up to 98%. Power range:1000va to 30kva Phase: single/three phase Input/output:customized Insulation class:ul class B, F, H, N Isolation:4KV
Sikes offers a complete line of industrial control transformers, which provide stepped-down voltages to machine tool control devices. It¡¡¥s specifically designed to meet high inrush industrial applications where electromagnetic components such as relay, solenoids and magnetic motor starters are used. Technical parameters Insulation class: h Environment exists without gas, steam, chemical deposition, dust or dirt that will affect transformer¡¡¥s insulation seriously, explosive or corrosive medium is not allowed. Standard: iec726:1982 dry power transformer , gb6450-86(equivalent to iec726:1982) Standard carton or wooden case based on the custom made product.
Isolation transformer is used for low-voltage distribution system, isolate load from power, reject stray common mode and dc voltages, ground loop potentials, electromagnetic interference (emi) and radio frequency interference (rfi) from Dielectric strength: l-l, l-g 4000vac/50hz/60s. Free of arcing breakage I se is less than 65db (to be measured at the point 1 meter away from the reactor horizontally) . Protection class: ip00 or as customer required. Insulation class: h Environment exists without gas, steam, chemical deposition, dust or dirt that will affect transformer¡¡¥s insulation seriously, explosive or corrosive medium is not allowed. Standard: iec726:1982 dry power transformer , gb6450-86(equivalent to iec726:1982) Standard carton or wooden case to the custom made transformer
Common mode choke is an important component in switching power supply, frequency inverter and ups. The choking High magnetic permeability Good frequency performance, initial permeability µ 0 can be adjusted according to insertion loss in different frequency ranges, which varies from 30000~100000 Very high initial permeability, an effective suppression of emi spike noise. Huge ranges of permeability adjustment Outstanding anti out-of balance current capacity Good temperature stability Paper ctn
Applications: 1.In the dc-immune current filtering and choking coiles in auto audio system, filtering inductance in power supply. 2.Smoothing inductor, stored inductance, dmc, pfc correction inductor, etc. Properties: 1.Made of fe-based amorphous ribbon, low loss in high frequency. 2.Magnetic circuit closing, reduction of flux leakage, excellent characteristics of anti-dc current skewing of magnetic field. 3.High permeability, to be adjusted by changing the winding turns. Paper ctn
Toroid cores for switching power supply made of nanocrystalline are featured by its high magnetic permeability and low loss. It's the ideal material for many components in single-ended, push-pull or bridge type high frequency switching power supply, such as main transformer, magnetic amplifier, choking coil, stored inductance, filtering inductance, common mode choke and spike blocker. Application: Main transformer, pulse transformer, control transformer, etc in medium and small power switching power supply modules. Applicable in different kinds of work mode, like single-ended, bridge type, push-pull, etc. Properties: High magnetic permeability and low coercivity Low loss, low temperature rise A flexible selection of cores with different magnetic performances according to the work mode of switching power supply. Paper cnt
1.Low leakage flux 2.Low hum noise 3.High efficiency 4.Light weight
The initial magnetic permeability and temperature stability between nanocrystalline soft magnet alloy and permalloy are similar. Under the same conditions of core sizes and characteristics, the weight of the former is much lighter (about 1/3 lighter), cost much lower. Applications: Electronic kwh meter Precise power meter Overcurrent protection in mechanical control apparatus Current control in industrial automation Good thermal stability Paper ctn
High saturation flux density---reducing core sizes. Rectangle structure---easily for coil assembly. Core cut---good resistance to the dc bias saturation capacity . Low loss---reducing temperature rise(1/5-1/10 of the silicone steel). Paper ctn
Overview Low no-load loss, better quality! Safety 1. Product accepts the NOMEX Paper Insulation System with high level of inflaming retarding, anti-explosion, and fire rating. 2. Professional technology, excellent performance in mechanical strength and short-circuit resistance and long serve time. Reliable 1. H-class heat-resisting temperature: 180¡æ,C-class level for the major insulating material (220¡æ) with efficient overload capacity. 2. Low partial discharge, high level of insulation with long serve time; 3. NBC protection, no crack display. Environmental Friendly Product uses Nomex Paper as the main insulation material, which create fire retardation, high insulation level, low partial discharge, long service life. Transformer Insulation Bass H, main material insulation class C, it increases the overloading capacity. Low noise level and the copper can be recycling after the life cycle of the transformer. Transformer has high capability to resists moisture, dust and salt. Amorphous Core 1) All raw material are supplied by Hitachi Metals with iron loss less than 70-80% of the standard silicon steel. 2) Company has special treatment, procedure and manufacturer process; which has patent number as: 200810238258.6, 20082015857.5, 200820215858.X, 200820215812.8, 200820215814.7. 3) Core structure is dean and strong, which do not influenced by the movement created during transportation. 4) The three column structure has capability to withstand high level harmonics, and vector group can be in Dyn11, Yyn0. Low Voltage Winding features LV uses high quality imported copper foil and class H insulation foil to apply on polyester-imides. In between each layer, it uses Nomex paper. Windings are insulated by vacuum pressure impregnation (VPI) systems, which make it into concrete form. Both ends of the winding drum have applied resin to seal the ends. 1) For better withstand of short circuit capability 2) For better thermo shock resistance and enhance the life expectancy of the transformer 3) Winding has high capability to resists moisture, dust and salt. High voltage winding features HV winding uses several layer coil type with vertical airway structure. It wraps Nomex paper on to copper for insulation. In between each layer, it uses Nomex paper for insulate. Vacuum, pressure, impregnation (VPI system has applied on the coil to make the structure concrete. Both ends are sealed by resin. 1) Multi-layer design can enhance the inrush capability 2) Enhance short circuit capability 3) High insulation level on the insulation material with good airway throughout the coil design, increase the capability of thermo shock. That way the transformer life expectancy is longer. 4) Winding has high capability to resists moisture, dust and salt
Our mature technology has fully considered the various types of high voltage inverter. We carefully developed zpsg dry-type nomex insulation the entire frequency transformers. Our products include 9-pulse, 12-pulse, 18-pulse and 27-pulse, which can be natural or air-cooled type transformer. The transformer is small and has strong overload capacity, low partial discharge, short circuit capability strong, flame retardant, low noise, and with energy saving of up to 40% significant advantages
Multi-layer winding coil Low-voltage coil adopted high quality foil and rolled with the automatic foil machine, argon arc welding with high-accuracy standard; presoak dmd in the interlamination as insulation material. Use presoak glass for insulation both outside and inside, sealed with epoxy resin, followed by solidify in the curing oven, in order to reached the target of high level of humidity resistance. About amorphous metal transformer Amorphous metal transformer introduction The development of the amorphous metal in 1970s, it has been widely used in 1990 for a high energy saving material for the transformer industry. Right now, over one million sets of amorphous metal type transformer had been connected to grid all over the world. The longest proven save and reliable transformer had been running for more than 30 years, and it still perform satisfactory in the power industry. The energy saving is huge and it shall be the new era products in the power industry
Overview High-class security level Sg10 product contains no flammable resin, with no combustion-supporting, no explosion and toxic gas. High-class reliability High-low voltage coil adopted the nomex system, dipping h-class impregnating varnish with vpi vacuum pressure system, and solidify under high heat. Product belongs to h- class(180¡æ), and c-class (220¡æ) for main insulation material, with high- class anti-short circuit capacity. 20% overload is allowed under good ventilation condition. Energy saving & environmental protection Material (copper, steel) recovery afterlife; Burning without toxic chemical substance for nomex paper; Degradation of insulation material, without polluting; Low no-load loss, energy saving; Low noise, flexible design
Low loss, low noise level, high stability This series product possesses four low and one high characteristics which are: low lose. Low noise, low temperature rising.Low partial discharge and high reliability, as well as core-hoisting free and no leakage. With the approval of national transformer quality inspection and testing center. Allthe index of the transformer achieve jb/t3837 standard
We are engaged in supply of a wide range of Power & Distribution Transformers from 160kVA to 415MVA, 500kV Class to fulfill the specific demands of the Power & Industrial sectors and the Railways. These Transformers find use in industries such as Power Utilities, Process Industries, Railways, Mines, Electricity Boards, Industrial users etc in both the Domestic as well as Global markets We also offer Switchgear products ranging from 3.3kV to 420 kV, to meet the requirements of electrical sub-stations and installations. Transformer Types Distribution (160kva & Above) Power Dry Type/Oil filled/Cast Resin
Good Good
Power transformer, bulk transformer Ei19-ei133
Input;110-220v Ei19-ei133