Drill Pipe Rotary Clamp Device is installed on the wellhead,when the kelly is not on the wellhead(inside the rotary table),it may give drill pipe a forward torque or backward torque,and to finish forward tptation or backward rotation and the hole raming operation instead of the kelly.The merits of it are:it can be directly installed on the wellhead or casing on the drill tools without unleashing the drill tools.It can accommodate drill pipe from 2 3/8 inch to 5 inch,the rated torque of it is 60KN.M.
Type QQP Pneumatic Spiders are utilized to grip drill pipe and tubing in oil weil repairing.
Type E Pneumatic Spiders are utilized to handle drill pipe and tubing in oil well repairing.This type spider can accommodate pipe from 2 3/8 to 7 5/8 inch,the rated load is 175 tons.
There are three types of DU series Drill Pipe Slips:DU,DUL and SDU.They are with large handing range and light weight.Thereinto,SDU slips have larger contacting areas on the taper and higher resistance strength.They are designed and manufactured according to API 7K Specification for drilling and well servicing equipment.
ZQ Drill Pipe Power Tong is an ideal wellhead tool for oil drilling,widely applied in making-up and breaking-out for well drilling and repairing on offshore and land.Open-throat design of the ZQ series with high mobility allows escaping from drilling pipe freely.The tong is a combination of spinning tong and torque tong.It substitutes cathead,suspension tong and spinning rope in making-up and breaking-out.
- Used for water - BS 21/ISO 228-1 -2000 threaded standard - Max working pressure 16 Bar - Max working temperature 120C - Size from 1/2" - 3/4"
Type C or CHD Pneumatic Spiders are utilized to handle drill pipe and tubing in oil well repairing.This type sipder can accommodate pipe from 1.315 to 5 1/2 inch,the rated load of type C pneumatic spider is 80 tons,the rated load of type CHD pneumatic sipder is 120 tons.
Type A drill collar slips(Woolley Style) are multi-segments slips.They can accommodate the changes of outer diameter after the abrasion of drill collar.They are with light weight,large handing scale and reliable quality.This kind of slips are designed and manufactured according to API Spec 7K Specification for drill and well servicing equipment.
DB Tong is used for marking up or breaking out the screws of drill tools and casing joint or coupling.It can be adjusted by changing latch lug jaws and handling shoulders.
R thread self drilling hollow bar anchor is composed by hollow anchor bolt, anchor nut, anchor plate, anchor coupler, drill bit, centralizer, and the hollow anchor bars can be cut and lengthened by coupling on request. Functions: R thread self drilling hollow bar anchor is an advanced system which can ensure the anchoring effect for complex ground conditions. It can be integrated with the functions of drilling, grouting and anchoring. Conditions: Tunneling Mining Slope Stabilization Foundation Support Features and advantages: 1. Safe, reliable, and time saving. 2. Simple installation & operation. 3. Choice of drill bits for different ground conditions. 4. Grouting works synchronize with drilling or after drilling. Grout can fill fractures effectively. 5. Anchor bars can be cut and lengthened on request, applying to narrow spaces. 6. It provides higher bonding stress than smooth steel pipe depending on continuous wave thread.
BOP parts that we supply all come from original manufacturers, they are 100% interchangeable/ BOP PART NAME: top sealing, front sealing, pipe ram, blind ram, slip ram, shear ram, spherical packer, bonnet, piston, shell. APPLY TO BELOW BOP: Brand: HYDRIL , SHENKAI BOP. RONGSHENG BOP ETC OTHER FAMOUS BRAND BOP Type :Annular BOP, Single Ram BOP, Double Ram BOP, Shear Ram BOP Standard: API Spec 16A,16C Working pressure:2000psi-15000psi(14 Mpa-105Mpa) Operating temperature:-18deg--121deg Bore size:7 1/16"-21 1/4" Top & nottom connection:Flanged,studded
Type TCI(Tungsten Carbide Insert) tricone bit IADC CODE Available 417 427 437 517 527 537 617 627 637 737 837 832 415 425 445 525 625 635 416 427 436 446 447 516 526 537 547 516 536 535 Available sizes: 3 3/4" (95mm), 4 1/8â??(105mm), 4 1/4"(108mm), 4 3/4â??(121mm), 5 5/8"(143mm), 5 7/8â??(149mm), 6â??(152mm), 6 1/4"(159mm), 6 1/2"(165mm), 6 3/4"(171mm), 7 1/2"(190mm), 7 7/8â??(200mm), 8 1/2â??(216mm), 8 3/4" (222mm), 9 1/2â??(241mm), 9 5/8"(245mm), 9 7/8"(250mm), 10 5/8"(269mm), 12 1/4"(311mm), 14 3/4"(348mm), 17 1/2"(445mm) Application formations Soft ,medium soft ,hard,medium hard,very hard formation Material Body: Alloy steel Tooth marterial: Tungsten carbide insert(TCI)
Roll-Forged Sheaves are available in many configurations in order to meet various oilfield applications. Roll-Forged sheaves are available in sizes up to 78 in diameter. Applications should provide for tightening separator plates against bearing cones to adjust and insure proper function of bearing. Each sheave in the table below has a machined bore sized to accept the respective bearing number shown. The sheaves are provided from the factory plain bore (the bearings are not included).
Air operated thread protector is also called Inflatable thread protector. It is used to protect the outer thread of casing and tubing pipe. Its outstanding feature is that its gas nozzle is manufactured on the facade, which can protect the gas nozzle in the pipes loading, unloading and transportation process. The gas nozzle of dismountable inflatable thread protector is on the side, which may damage the gas nozzle. Inflatable thread protector is made from polyurethane containing a stainless steel ring in it, so integral inflatable thread protector is resistant to corrosion, abrasion and oil. It has many advantages, such as fast inflation, easy operation, good air-tightness, lowering consumption and cost. Besides, it can be repeatedly used. Features: The Air operated Thread Protectors provide a 360�° grip with greater, evenly divided holding power. - Durability is enhanced because the outside of the protectors does not change; only the inside inflates to provide a better grip on the pin. -Absence of moving parts, metal clamping bars, or other mechanisms provides a long and virtually maintenance-free life cycle. -The bottom of each protector contains a rugged buffer. -Air operated thread protectors provide firm attachment to all thread types for greater operational flexibility. -Rugged construction makes this protectors resistant to high temperatures and rough handling for a long life cycle. -Pressurization by air facilitates installation and release for operational efficiency.
Fill and Circulate Tool (hereafter referred to as FAC Tool) is a surface tool used during the casing running operation. The FAC Tool is designed to both fill the casing with drilling fluid while running it in the hole and to enable quick circulation of the casing string at any time without installation of a casing swage. The FAC Tool has features with easy â??to- use , safe and reliable , no leakage and so on, which lightens labor intensity of workers greatly and improves operation environment of well. The FAC Tool is composed of ten parts (shown in figure) , whose main function of components are below: 1. Drill Pipe Connector: The FAC Tool built for top drive rigs connects to the drill pipe threads of the rigâ??s top drive unit via the Drill Pipe Connector. The threads of the Drill Pipe Connector are standard 4 1/2 IF, but crossovers are available for other drill pipe threads. 2. Extension: For applications where long elevator links are used, Extensions are placed between the Drill Pipe Connector and the Mandrel. On the Extension are two Pad Eyes that make it easy to manipulate the Tool around the Rig during rig up or rig down. Also, while the Tool is in use, a Safety Cable attaches to one of the Pad Eyes in the event the Tool should accidentally come loose from the top drive. In place of the Extensions, a Drill Pipe Pup can be used between the top drive connection and the Drill Pipe Connector instead of extension. 3. Mandrel: The Mandrel houses the specially designed Seal Assembly that is used to seal off the casing string. The Seal Assembly has three parts: the Seal Retainer, the Sealing Element, and the Gauge Ring. 4. Seal Retainer: Aluminum part that keeps (retains) the Sealing Element from being extruded upward while circulating. 5. Sealing Element: Elastomeric Seal that seals off the casing for circulation. It is hollow so circulation pressure can energize the seal it creates against the casing bore. 6. Gauge Ring: Tapered Aluminum piece that guides the Seal Assembly into the pipe and has holes to allow energizing pressure into the Sealing Element. 7. Retainer Sub: The Seal Assembly is held in place with the flexible hose. 8. Flexible Hose: The Retainer Sub is also used to connect a high pressure Flexible Hose. This Hose prevents any hard stack out between the FAC Tool and the casing and compensates for misalignment and casing movement during make up. 9. Mud Saver Valve: Below the Flexible Hose is the heart of the FAC Tool, the Mud Saver Valve. It is essentially a two-way check valve. This Valve opens with pressure when the mud pump is turned on and closes when the mud pump is turned off. It also permits flow in the upward direction for releasing pressure.
Pneumatic tube clutch For well drilling rig Supply API Drawworks Pneumatic Tube Clutch and various spare parts ! Pneumatic clutch is a friction clutch with compressed air as the power source for operation. It is generally used on equipment that needs to transmit large torque and change the rotation direction quickly, such as oil drilling machinery, ships, large mechanical presses,excavators,ball mills, rubber and plastic machinery, etc. Pneumatic clutch is a friction clutch with compressed air as the control power source.Generally used in the need to transfer large torque and rotating direction at a fast speed of the equipment, such as oil drilling machinery, ships, paper, mining, large mechanical presses, excavators, rubber and plastic machinery. Pneumatic clutch has large transmission torque, stable engagement, easy to install, vibration absorbing, and can compensate a small amount of angular and radial relative offset of the main and driven axes. The driven part has small inertia, long service life, compact structure and good sealing.However, the deformation resistance of the pneumatic tube is large, the material cost of the pneumatic tube is high, the use temperature is limited, more than 60â?? will reduce the life of the pneumatic tube, lower than -20â?? easy to make the pneumatic tube brittle. Pneumatic clutch joint components mainly use friction plate, friction shoe and so on.The pneumatic clutch is composed of rim,brake shoe, friction plate, torque bar, release spring and rubber air tube.The working process of the pneumatic clutch is realized by the pneumatic tyre charging and discharging. The pneumatic tyre is the key part of the pneumatic clutch.The rubber air tube is vulcanized by the outer rubber layer, the inner rubber layer, and the curtain cloth layer. 1. Small appearance, but can transmit a lot of rotating force. 2. It has strong durability and wear resistance. 3. Long product life, safe and convenient operation. 4. The clutch can be easily installed or uninstalled when transmitting power.
Pneumatic tube clutch For well drilling rig Supply API Drawworks Pneumatic Tube Clutch and various spare parts ! Pneumatic clutch is a friction clutch with compressed air as the power source for operation. It is generally used on equipment that needs to transmit large torque and change the rotation direction quickly, such as oil drilling machinery, ships, large mechanical presses,excavators,ball mills, rubber and plastic machinery, etc. Pneumatic clutch is a friction clutch with compressed air as the control power source.Generally used in the need to transfer large torque and rotating direction at a fast speed of the equipment, such as oil drilling machinery, ships, paper, mining, large mechanical presses, excavators, rubber and plastic machinery. Pneumatic clutch has large transmission torque, stable engagement, easy to install, vibration absorbing, and can compensate a small amount of angular and radial relative offset of the main and driven axes. The driven part has small inertia, long service life, compact structure and good sealing.However, the deformation resistance of the pneumatic tube is large, the material cost of the pneumatic tube is high, the use temperature is limited, more than 60â?? will reduce the life of the pneumatic tube, lower than -20â?? easy to make the pneumatic tube brittle. Pneumatic clutch joint components mainly use friction plate, friction shoe and so on.The pneumatic clutch is composed of rim,brake shoe, friction plate, torque bar, release spring and rubber air tube.The working process of the pneumatic clutch is realized by the pneumatic tyre charging and discharging. The pneumatic tyre is the key part of the pneumatic clutch.The rubber air tube is vulcanized by the outer rubber layer, the inner rubber layer, and the curtain cloth layer. 1. Small appearance, but can transmit a lot of rotating force. 2. It has strong durability and wear resistance. 3. Long product life, safe and convenient operation. 4. The clutch can be easily installed or uninstalled when transmitting power.
Pneumatic tube clutch For well drilling rig Supply API Drawworks Pneumatic Tube Clutch and various spare parts ! Pneumatic clutch is a friction clutch with compressed air as the power source for operation. It is generally used on equipment that needs to transmit large torque and change the rotation direction quickly, such as oil drilling machinery, ships, large mechanical presses,excavators,ball mills, rubber and plastic machinery, etc. Pneumatic clutch is a friction clutch with compressed air as the control power source.Generally used in the need to transfer large torque and rotating direction at a fast speed of the equipment, such as oil drilling machinery, ships, paper, mining, large mechanical presses, excavators, rubber and plastic machinery. Pneumatic clutch has large transmission torque, stable engagement, easy to install, vibration absorbing, and can compensate a small amount of angular and radial relative offset of the main and driven axes. The driven part has small inertia, long service life, compact structure and good sealing.However, the deformation resistance of the pneumatic tube is large, the material cost of the pneumatic tube is high, the use temperature is limited, more than 60â?? will reduce the life of the pneumatic tube, lower than -20â?? easy to make the pneumatic tube brittle. Pneumatic clutch joint components mainly use friction plate, friction shoe and so on.The pneumatic clutch is composed of rim,brake shoe, friction plate, torque bar, release spring and rubber air tube.The working process of the pneumatic clutch is realized by the pneumatic tyre charging and discharging. The pneumatic tyre is the key part of the pneumatic clutch.The rubber air tube is vulcanized by the outer rubber layer, the inner rubber layer, and the curtain cloth layer. 1. Small appearance, but can transmit a lot of rotating force. 2. It has strong durability and wear resistance. 3. Long product life, safe and convenient operation. 4. The clutch can be easily installed or uninstalled when transmitting power.
Pneumatic tube clutch For well drilling rig Supply API Drawworks Pneumatic Tube Clutch and various spare parts ! Pneumatic clutch is a friction clutch with compressed air as the power source for operation. It is generally used on equipment that needs to transmit large torque and change the rotation direction quickly, such as oil drilling machinery, ships, large mechanical presses,excavators,ball mills, rubber and plastic machinery, etc. Pneumatic clutch is a friction clutch with compressed air as the control power source.Generally used in the need to transfer large torque and rotating direction at a fast speed of the equipment, such as oil drilling machinery, ships, paper, mining, large mechanical presses, excavators, rubber and plastic machinery. Pneumatic clutch has large transmission torque, stable engagement, easy to install, vibration absorbing, and can compensate a small amount of angular and radial relative offset of the main and driven axes. The driven part has small inertia, long service life, compact structure and good sealing.However, the deformation resistance of the pneumatic tube is large, the material cost of the pneumatic tube is high, the use temperature is limited, more than 60â?? will reduce the life of the pneumatic tube, lower than -20â?? easy to make the pneumatic tube brittle. Pneumatic clutch joint components mainly use friction plate, friction shoe and so on.The pneumatic clutch is composed of rim,brake shoe, friction plate, torque bar, release spring and rubber air tube.The working process of the pneumatic clutch is realized by the pneumatic tyre charging and discharging. The pneumatic tyre is the key part of the pneumatic clutch.The rubber air tube is vulcanized by the outer rubber layer, the inner rubber layer, and the curtain cloth layer. 1. Small appearance, but can transmit a lot of rotating force. 2. It has strong durability and wear resistance. 3. Long product life, safe and convenient operation. 4. The clutch can be easily installed or uninstalled when transmitting power.
Pneumatic tube clutch For well drilling rig Supply API Drawworks Pneumatic Tube Clutch and various spare parts ! Pneumatic clutch is a friction clutch with compressed air as the power source for operation. It is generally used on equipment that needs to transmit large torque and change the rotation direction quickly, such as oil drilling machinery, ships, large mechanical presses,excavators,ball mills, rubber and plastic machinery, etc. Pneumatic clutch is a friction clutch with compressed air as the control power source.Generally used in the need to transfer large torque and rotating direction at a fast speed of the equipment, such as oil drilling machinery, ships, paper, mining, large mechanical presses, excavators, rubber and plastic machinery. Pneumatic clutch has large transmission torque, stable engagement, easy to install, vibration absorbing, and can compensate a small amount of angular and radial relative offset of the main and driven axes. The driven part has small inertia, long service life, compact structure and good sealing.However, the deformation resistance of the pneumatic tube is large, the material cost of the pneumatic tube is high, the use temperature is limited, more than 60â?? will reduce the life of the pneumatic tube, lower than -20â?? easy to make the pneumatic tube brittle. Pneumatic clutch joint components mainly use friction plate, friction shoe and so on.The pneumatic clutch is composed of rim,brake shoe, friction plate, torque bar, release spring and rubber air tube.The working process of the pneumatic clutch is realized by the pneumatic tyre charging and discharging. The pneumatic tyre is the key part of the pneumatic clutch.The rubber air tube is vulcanized by the outer rubber layer, the inner rubber layer, and the curtain cloth layer. 1. Small appearance, but can transmit a lot of rotating force. 2. It has strong durability and wear resistance. 3. Long product life, safe and convenient operation. 4. The clutch can be easily installed or uninstalled when transmitting power.
