Custom ADSS Tension Clamp ADSS Tension Clamps are used to connect ADSS cables to poles/towers. Armored rods provide protection and cushioning for the ADSS cables. The special design of the prefabricated rods ensures that the tension clamps do not overstress the ADSS cables, thus ensuring a normal service life of the cable system.The ADSS tension clamps are made of aluminium-clad or galvanized steel wire. Structure and raw materials Unshackle - hot-dip galvanized steel. The shackle is connected to the reinforcing bar unit. Twisted chain ring - hot dipped galvanized steel. Twisted links are used to connect the shackle to the thimble. Sleeve - hot dip galvanized cast steel. The sleeve is inserted into the unclamp of the tension clamp to provide protection and connection. Armored rod ----- Aluminum clad steel wire. Armored rods increase friction through a layer of granular emery inside the cable. The rods are shop assembled into four subsets to minimize misalignment errors and speed installation. The ends are bent outward to provide strain relief in critical cable departure areas. Prefabricated Dead Ends - Prefabricated dead ends are made from hot-dip galvanized steel wire or aluminum-clad steel wire and are assembled in the shop into a subset with a solid layer of emery to increase the grip of the tensioning clamps while reducing lateral pressure. Direction 1. Used for connecting connecting poles (towers) to terminal poles (towers), tension poles, or poles (towers) with line clamping angles of 25�° or more. Special specifications: 1 unit for each terminal pole (tower), 2 units for each tension pole (tower), and 2 units for each connecting pole (tower). You can select the specification model corresponding to the appropriate cable diameter range, maximum allowable tension (MAT) or span length from the data sheet.
Different sizes and material
Clamp is used to clamp a strut channel with I-beam or a channel and is highly used in variegated lifting operations to save energy and time. These are widely used in power plants and major construction sites etc.
ADSS Downlead Clamp DownLead Clamp, also called lead wire pads, are fixed to poles or strain relief towers to guide fiber optic cables up or down through them. According to the application, the lead wire clips include tower lead wire clips, pole lead wire clips, ADSS lead wire clips and OPGW lead wire clips. Downlead Clamp DownLead Clamp, also called lead wire pads, are fixed to poles or strain relief towers to guide fiber optic cables up or down through them. According to the application, the lead wire clips include tower lead wire clips, pole lead wire clips, ADSS lead wire clips and OPGW lead wire clips. The downlead clamp consist of a stainless steel band and a rubber part. The stainless steel band is used to fix the rubber clip on the pole. At the same time, the rubber part fixes the optical fiber. This way, the fiber does not shake and at the same time reduces damage caused by friction. The lead wire clamps for towers have a different structure than the lead wire clamps for poles. The clamps consist of steel brackets, bolts and nuts, and rubber parts. The bolt secures the lead clip to the tower. Compared to other lead clip manufacturers, Huaneng offers the end user a wide range of lead clip design options. huaneng lead clips can be custom manufactured with a wide range of cables, materials and different connection options.
OPGW the Preformed Helical Tension Clamp The OPGW Premored/Helical Tension Clamp is primarily used to install cables with RTS less than 160 kN to tension towers/poles, corner towers/poles and terminal towers/poles. A complete set of OPGW prefabricated/spiral tensioners includes aluminum alloy or aluminum clad steel dead ends, structural reinforcement rods, support fittings and grounding clamps, etc. Wire Tension Clamp An OPGW (Optical Ground Wire) wire tension clamp is a specialized device used in the installation and maintenance of OPGW cables. OPGW cables are composite overhead cables that combine optical fibers for communication purposes with a metallic ground wire for power transmission and grounding. The OPGW wire tension clamp serves the purpose of securely attaching the OPGW cable to the supporting structure, such as poles or towers, while maintaining the necessary tension. It plays a crucial role in ensuring the stability and reliable performance of the OPGW system.
SUMIP supply various types of single clamps used to LT & HT single cables. Hardware: MS zinc paslivated with optional Hardward available in hot dip galvanized or SS 304 / 316 Advantages: High Mechanical Strength No Corrosion Resistant against various chemicals Do Not Oxidize Diameter: 42 - 120 mm
Place of Origin Hubei, China Type Rail Clamp Material Stainless Steel Brand Name Linkage Model LJ-JJQT Weight 6.5kg Packaging and delivery Packaging Details Wooden box export standard/ Woven bag+paper carton, 1 unit/Carton box, G.W: 6.5KG Selling Units: Single item Single package size: 60X60X60 cm Single gross weight: 6.500 kg
OPGW Performed Helical Suspension Clamp The unique design of the lightweight HuaNeng Fitting mechanical suspension supports spans of optical ground wire (OPGW) cables through a wide range of line angle variations. HuaNeng Fitting's mechanical suspension is easy to install while supporting vertical, lateral, and longitudinal unbalanced loads and angular tension without damaging cable strands or affecting fiber performance. Separate bolts OPGW Suspension Clamp Suspension clamps are also known as overhanging wire clamps or overhanging fixtures. According to the use, opgw suspension clamp include ABC cable overhanging wire clamps, ADSS cable overhanging wire clamps, and overhead line overhanging wire clamps. Suspension wire clamp is a general term for all types of wire clamps that suspend wires or cables from a pole tower. Pre-twisted opgw cable clamps are used for the connection of OPGW cables and towers to reduce the static stress at the support point of OPGW cables, to improve the vibration resistance of ADSS cables, to buffer the dynamic stress of wind vibration, and to ensure that the cable bends within the permissible value, so that the cable does not produce bending stress, so that the optical fiber does not produce additional loss in the cable after installation.
OPGW Preformed Double Tension Clamp Preformed tension clamps are also named preformed dead-end or dead-end cable clamps for communication ADSS fiber, OPGW cable or OPPC. A preformed dead end is a tension wire that has an important role in ADSS/OPGW transmission lines. Dead-end cable clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. Preformed Tension Clamp Preformed tension clamps are also named preformed dead-end or dead-end cable clamps for communication ADSS fiber, OPGW cable or OPPC. A preformed dead end is a tension wire that has an important role in ADSS/OPGW transmission lines. Dead-end cable clamps are designed to connect ADSS/OPGW/OPPC to overhead towers or poles. The unique pre-formed tension clamp design not only simplifies installation, but also ensures a secure cable connection. Dead-end cable clamps provide superior performance to protect ADSS/OPGW/OPPC cables from stress point damage and prevent signal degradation during transmission. Pre-formed tension clamps for conductors and grounds are similar in appearance to pulling dead-end clamps, but the specifications, raw materials and strength requirements of the two types of pulling clamps do differ significantly. Although there are different design standards in different countries, we can OEM to customer requirements. As an experienced manufacturer and supplier of preformed tension clamps, Seinei understands the standards, the manufacturing process and understands your needs. If you have any questions, please feel free to contact us.
CM500A 600A AC Clamp Meter CM510A 600A AC Clamp Meter (Temperature function) CM520A 400A DC/AC Clamp Meter CM530A 600A DC/AC Clamp Meter CM550A 1020KVA Power DC Clamp Meter CM210C 20.00A~200A DC/AC Mini Clamp Meter CM210E 2.000 A~200A DC/AC Mini Clamp Meter CTA600 600A AC A Current Clamp Meter Module
ADSS Preformed Suspension Clamp The base is attached by a rear hinge for quick and easy installation of ADSS cables Cushioned pad made of UV resistant neoprene sleeve insert to gently hold the ADSS cable in place Includes stainless steel bolts and locking washers for locking clamps ADSS Suspension Clamp Suspension clamps are also called fixture suspension or suspension fittings. According to the application, the suspension clamps are divided into ABC optical cable suspension clamps, ADSS optical cable suspension clamps, and overhead line suspension clamps. ADSS Optical Cable Suspension Clamp Suspension cleats for ADSS cables are also known as prefabricated suspension cleats. Prefabricated catenary clamps that function the same as ordinary catenary clamps are designed to suspend conductors or ground wires in a vertical direction. Huaneng prefabricated suspension clamps are suitable for high voltage above 220kv. Unique features of prefabricated suspension clips: Effective protection of conductors Avoiding Electricity Waste Due to Corona easy installation Prefabricated suspension clamps are designed to protect ADSS (All Dielectric Self Supporting) cables from sloshing caused by wind currents. Suspended clamps are widely used in transmission lines, towers or power distribution systems. The distance between the two towers is called the span. For short spans, prefabricated suspension clamps with O-rings are often used. This kind of suspension clamp has the characteristics of lightest weight, convenient installation, and can protect ADSS optical cable more effectively. For mid-span and long-span, there is also a prefabricated suspension clamp that is aluminum-clad. The Armor Clip Suspension connects with U-Clips to hang cables. Aluminum-clad suspension clamps support and protect ADSS fiber optic cables from bending damage. According to the span, the short span adopts single suspension clamp, and the long span adopts double suspension clamp. Composition: inner pre-twisted wire, the outer pre-twisted wire, rubber insert, cast aluminum shells, right-angle shackle, U-type shackle. Purposes: supporting cable, make the ADSS hang on the tower.
ADSS with The DN Short-span Tension Clamp ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. Tension Clamp ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. The ADSS tension clamp is typically made of corrosion-resistant materials such as aluminum or plastic and is available in different sizes to fit various cable diameters. Composition: twisted wire, thimble, PH-type shackle, U-type shackle etc. Purposes: support all strain, make ADSS cable connect the strain pole and tower. Features: Preformed wire connect the pole and tower by thimbles etc. link fitting, afford the load of the transmission line. Grip strength not less than cable 95%RTS in case that not more than lateral pressure of the cable E xcellent aluminum clad steel improve the mechanical and resist-corrosion function, extend life. Corrosion-resistant materials such as aluminum or plastic to ensure durability and longevity. Gripping mechanism that securely holds the cable without causing damage. Tensioning mechanism that allows for adjustment of the cable tension. Insulating material to protect the cable from electrical currents. Suitable for use with a range of cable diameters. Easy installation and maintenance. Technical requirements: meet the DL / T 766-2003 ADSS with the preformed helical fittings technical requirements and test methods
ADSS Downlead Clamp DownLead Clamp, also called lead wire pads, are fixed to poles or strain relief towers to guide fiber optic cables up or down through them. According to the application, the lead wire clips include tower lead wire clips, pole lead wire clips, ADSS lead wire clips and OPGW lead wire clips. Downlead Clamp DownLead Clamp, also called lead wire pads, are fixed to poles or strain relief towers to guide fiber optic cables up or down through them. According to the application, the lead wire clips include tower lead wire clips, pole lead wire clips, ADSS lead wire clips and OPGW lead wire clips. The tower clamps consist of a stainless steel band and a rubber part. The stainless steel band is used to fix the rubber clip on the pole. At the same time, the rubber part fixes the optical fiber. This way, the fiber does not shake and at the same time reduces damage caused by friction. The lead wire clamps for towers have a different structure than the lead wire clamps for poles. The clamps consist of steel brackets, bolts and nuts, and rubber parts. The bolt secures the lead clip to the tower. Compared to other lead clip manufacturers, Jingyoung offers the end user a wide range of lead clip design options. huaneng lead clips can be custom manufactured with a wide range of cables, materials and different connection options.
Tension Clamp for Earth Wire Tension Clamp For Earth Wires are for use by trained craftsmen only. Dead-end clamps should not be used by anyone unfamiliar or untrained in their use. Wire Tension Clamp Tension clamps are designed to non-rigidly secure installation cables to brackets, fasteners on buildings, or utility poles. Cable clamps are installed at the beginning and end of cable runs, suspensions, branches and turns. Tension clamps can also be used where cables sag on large straight sections or form under the influence of increased tensile loads. The design of the products is simple. One of the most popular consists of a cone, a pair of plastic toothed wedges that act as clamping devices, and a steel ring. The principle of operation is simple and consists of self-tensioning the cable using the movable wedges of the clamp. The sale of tension clamps and their use significantly reduces the time and physical costs of installation work. This cable attachment element offers the following advantages There is no need to strip the insulation to expose the mating cable during use; Simple installation, reducing the possibility of errors; No special training of installers is required; No special tools are required to prepare cables for installation; Reduced risk of cable damage and compromised integrity.
ADSS Preformed Suspension Clamp The base is attached by a rear hinge for quick and easy installation of ADSS cables Cushioned pad made of UV resistant neoprene sleeve insert to gently hold the ADSS cable in place Includes stainless steel bolts and locking washers for locking clamps ADSS Suspension Clamp Suspension clamps are also called fixture suspension or suspension fittings. According to the application, the suspension clamps are divided into ABC optical cable suspension clamps, ADSS optical cable suspension clamps, and overhead line suspension clamps. ADSS Optical Cable Suspension Clamp Suspension cleats for ADSS cables are also known as prefabricated suspension cleats. Prefabricated catenary clamps that function the same as ordinary catenary clamps are designed to suspend conductors or ground wires in a vertical direction. Huaneng prefabricated suspension clamps are suitable for high voltage above 220kv. Unique features of prefabricated suspension clips: Effective protection of conductors Avoiding Electricity Waste Due to Corona easy installation Prefabricated suspension clamps are designed to protect ADSS (All Dielectric Self Supporting) cables from sloshing caused by wind currents. Suspended clamps are widely used in transmission lines, towers or power distribution systems. The distance between the two towers is called the span. For short spans, prefabricated suspension clamps with O-rings are often used. This kind of suspension clamp has the characteristics of lightest weight, convenient installation, and can protect ADSS optical cable more effectively. For mid-span and long-span, there is also a prefabricated suspension clamp that is aluminum-clad. The Armor Clip Suspension connects with U-Clips to hang cables. Aluminum-clad suspension clamps support and protect ADSS fiber optic cables from bending damage. According to the span, the short span adopts single suspension clamp, and the long span adopts double suspension clamp. Composition: inner pre-twisted wire, the outer pre-twisted wire, rubber insert, cast aluminum shells, right-angle shackle, U-type shackle. Purposes: supporting cable, make the ADSS hang on the tower.
We manufacture PVC,TPE and EPDM Profiles for pipe clamps in any sizes as our customer regusted.
Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur.
Product Full Description Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur.
SPM Pipe welding pneumatic clamps assure a rapid, accurate alignment of two joints of pipe during the welding operation. Front and rear heads operate independently to lock the clamp into position. A specially designed shoe on each head exerts pressure uniformly around the inside circumference of the pipe to maintain necessary alignment. Each pipe welding pneumatic clamp is easily and quickly adjusted for different pipe wall thicknesses.
In the realm of life-saving technology, the IT Clamp stands as a testament to innovation, efficiency, and reliability. This revolutionary anti-hemorrhaging device has not only been rigorously tested but has also proven its effectiveness in the field, garnering the endorsement of U.S. EMTs and the U.S. military. Key Benefits of the IT Clamp: Proven Lifesaver: The IT Clamp has demonstrated its life-saving potential in real-world scenarios, helping to control severe bleeding and stabilize patients in critical situations. FDA Approval: Our device has received full approval from the U.S. Food and Drug Administration, attesting to its safety and efficacy. Global Impact: The IT Clamp is now making its impact felt worldwide, with shipments reaching various corners of the globe. It is fast becoming an indispensable tool in emergency medical care. Ease of Use: Designed with simplicity in mind, the IT Clamp can be easily applied by medical professionals, first responders, and even laypersons with minimal training. Compact and Portable: Its compact size and portability make it a convenient addition to any medical kit, ensuring rapid response to bleeding emergencies. We believe that the IT Clamp could be an invaluable asset in your medical toolkit. To discuss this exceptional device further, we would be delighted to arrange a presentation or provide you with additional information.
