Wood sawdust dryer / wood chips dryer General instruction of wood sawdust dryer: 1. Rotary drum type dryer, there are 31 pipes in it, hot air enter pipes directly. 2. Hot air in pipes, biomass materials outside, so biomass materials can avoide be ignited. 3. Indirect heating source prevent raw materials polluted by smoke and dust. 4. Specail desing can make hot air circulate in rotary drum body, and shorted drying time. 5.Brick heaint stove, there are three walls in it with differetn funcationsl, specical structure can prevent smoke, flame and dust enter pipes, just enter clean hot air. 6heating source can be coal, charcoal, wood, gas, oil, wind power etc. Characters of wood sawdust dryer: 1is mainly to dry biomass or fertilizer powder materials , at max feed 15mm dimension materials, it has changeable speed rotary drum , which can dry high humidity materials, such as to dry biomass from sawdust, straw, stalk, e.C.T and fertilizer materials from poultry manure , home or Factory waste 2.Machine dryer drum rpm can be controlled according to raw materials humidity. If humidity is large, then can control feeding speed and drum rpm lower to make longer drying time. The longer drum ensure high heat use efficiency. 3. Has temperature adjusting equipment between stove and dryer, which can adjust the hot air temperature before feeding to drum according to raw materials humidity , after adjusting, then feed to dryer drum 4. Rotaryd drying machine has two ways to discharge materials, One is to outlet from rotary drum bottom, it is mainly fit for large weight ratio materials
Biomass wood sawdust pellet mill is designed specially for the raw material which are hard to press and hard to shape. Biomass wood sawdust pellet mill can press wood, wood chips, sawdust, straw, stalk, shell, rice husk, sunflower seed, peanut shell into good pellets with 1.1-1.4 g/cm3 density. Biomass wood sawdust pellet mill is an ideal optiona for pellet making business, it can deal with most raw material, such as agro-waste, agriculture waste, fruit shell, rank grass and any other wood waste. Biomass wood sawdust pellet mill have double layer die which lengthen the lifetime of the die a lot. It has advantages of flat die pellet mill and ring die pellet mill. They are the best choice for pellet mills for fuel pellets. Seven characteristics of the biomass wood sawdust pellet mill: 1) vertical feeding directly in place. 2) die static, roller rotating, materials centrifugal, evenly distributed around. 3) double layer dies, up and down dual use, reduce the cost, enhance the efficiency, can be dual use. 4) one die, different hole diameters, with different specifications to pelleti. 5) macroporous die, wire joining circular tube, increasing travel, improving density. 6) ring die, vertical structure, good for cooling the pelletizing room. 7) independent and frequebct conversion discharge device, to ensure that the rate of pellet production. Four differences 1) upward mould, special structure, vertically feeding and easier heat disspassion. 2) die static, roller rotating, material centrifugal and distribute around evenly. 3) double layer die, multi function, high efficiency. 4) macroporous die, wire joining circlar tube, increasing travel, improving density.
Wood chip crushers are commonly used shredding equipment for processing sawdust of different finenesses. The wood chip crusher can quickly wood , bark,branches,leaves,thatch,bamboos, straws, and other biomass materials into sawdust, and the production efficiency is very high. This industrial machine shredder is a new type of superfine wood processing equipment. Wood chip crusher machine also can be called wood shredder, wood grinder, bamboo mill(milling machine), branches pulverizer. The processing size of the raw materials for the high-efficient wood crusher ranges from 1cm to 20cm, and the final sawdust size can be decided according to the customer's requirements.
1. Application Wood chip Crushers are commonly used as shredding equipment for processing sawdust of different finenesses. The Wood chip crusher can quickly wood, bark, branches, leaves, thatch, bamboos, straws, and other biomass materials into sawdust, and the production efficiency is very high. This industrial machine shredder is a new type of superfine wood processing equipment. Wood chip crusher machines also can be called wood shredder, wood grinder, bamboo mill(milling machine), branches pulverizer. The processing size of the raw materials for the high-efficient wood crusher ranges from 1cm to 20cm, and the final sawdust size can be decided according to the customer's requirements. 2.The basic structure 1.Feed inlet 2.Machine cavity 3.Discharge outlet 4.Mainshaft bearing 5.Machine cavity 6.Machine chassis 7.Copper wire motor8.Pulley guard 9.strainer mesh(3-30mm) 3.OPERATING PRINCIPLE With a fineness analyzer, this wood shredder machine is specialized in crushing lightweight materials, fiber materials, brittle materials, ductile materials, and other special materials. This sawdust-making machine can crush the branches with a diameter of less than 20cm. The main parts of the wood crusher include the feed port, main body, outlet, motor, and holder. As for the main body, there are knife plates, hammers and screen meshes inside. And the quantity of the knife plates and hammers varies according to the model of the wood crushing machine. Generally, the diameter of the holes in the screen mesh is 8mm, but we can also customize the screen mesh for customers' special requirements. The larger the diameter of the mesh holes, the greater the discharging speed and the output of the crushed materials.
Product Introduction The sawdust dryer is used for pellet sawdust or powder sawdust. Wet materials are continuously sent into drum through screw conveyer and then get separated and pushed by high-speed hot flow. The moisture in wet materials is taken away in this process and then we get powder or pellet dry materials. Product Application Sawdust dryer are widely used for the drying of straw briquette, charcoal, wood pellet fuel, sawdust briquette, corn straw, soybean straw, cotton stalk, wheat straw, sorghum stalk, wood shavings, sawdust, gingko leaf, mulberry leaves and other fiber materials. Product Configuration Sawdust dryers are consist of heating furnace, feeding port, drum, filter drum, conveying pipe, cooling drum and discharging port.
The sawdust dryer is used for pellet sawdust or powder sawdust. Wet materials are continuously sent into drum through screw conveyer and then get separated and pushed by high-speed hot flow. The moisture in wet materials is taken away in this process and then we get powder or pellet dry materials. Sawdust dryer are widely used for the drying of straw briquette, charcoal, wood pellet fuel, sawdust briquette, corn straw, soybean straw, cotton stalk, wheat straw, sorghum stalk, wood shavings, sawdust, gingko leaf, mulberry leaves and other fiber materials.
Ring die pellet mills are widely used in the granulation of wood, straw, and other biomass sources. Driven by heavy-duty gearbox construction, it can work continuously in even most adverse conditions. The imported key elements are of high performance with long life and low maintenance cost. The key parts of the ring die pellet mill are made of alloyed steel that is very strong and malleable. Ring die pellet mills die is made of stainless steel. Our ring dies pellet mills capacity ranges are from 200kgs to10T per hour.
Name Professional wood sawdust block making machine Introduction wood sawdust block making machine is mainly used for wood waste materials, such as wood shavings,sawdust and so on
Name Top quality wood pallet making machine Introduction wood pallet making machine is mainly used for wood waste materials, such as wood shavings,sawdust and so on
Name High compressed wood block making machine Introduction wood block making machineis mainly used for wood waste materials, such as wood shavings,sawdust and so on
Wood hammer crusher to make fine wood sawdust is a kind of new type machine combined with chipper and grinder. It can be used for different materials for using, such as tree trunk, branches, stalks, forage wood wastes and so on. The series of hammer crushers for sale products have the features of small volume ,light weight ,simple structure ,easy operation and maintenance ,high ratio of crushing ,too little crush , even product size ,high producing capacity .They are suitable for crushing all the materials of brittle,medium hard ,and compressive strength 150 Mpa.The features include great hammerhead work ,adoption of new technology casting ,with wear and impact resistance. This solve the problems of crushing plant dust pollution and gray body leakage.
Applications: Briquette Press YE83-250 is applied in steel mills, foundries, recycling plants, ferrous & non ferrous smelting industry to press scrap metal chips (max. length 40mm) into high density briquettes (cylinders). Briquette Press YE83-250 is good for briquetting of cast iron powder, crushed steel turnings, aluminum swarf, copper milling chips, all sorts of metal sawdust, particles, chips & fins, and metal cans shreded to small pieces (smaller than 40mm). Briquette Press YE83-250 is NOT SUITABLE for: wood sawdust, coir fibre, biomass material. Features: 1. Vertical briquette press, briquette density is high. 2. Robust machine of solid structure, special alloy for press mould liners. 3. Hydraulic oil cooler: standard water cooler (need cooling tower to supply cool water); optional normal air cooler, or compulsory air cooler (air cooler with compressor). 4. Magnetic return oil filter. NOK (Japan) seals for cylinders. 5. Hydraulic drive, Mitsubishi PLC operation. 6. Feeding conveyor & vibrating motor are optional for charging of material. YE83-250 Main Parameters: Main cylinder force: 200 MT Auxiliary cylinder force: 55 MT Press mould size: dia110Ã?H300 / dia120Ã?H300 MM Briquette size: dia110Ã?H(70-100) / dia120Ã?H(70-100) MM Briquette weight: 3.6-5.2 / 4.1-5.9 kg (cast iron) Production rate: 1000-1100 kg/hr (cast iron) Electric motor: 22 kW
Product Introduction Hammer-type wood crusheris currently the most widely used wood production mill, the series is absorbed in avariety of wood mill on the merits of the development of advanced fine crushing equipment. With high productivity, low energy consumption, crushing effect is good, crushing uniform, simple operation and easy maintenance. At the same time the device is equipped with dust suction device, small powder pollution, in line with environmental requirements. Raw material The range of raw materials for wood crushers is quite is quite wide, and awide variety of waste wood raw materials can be used for crushing,such as twigs, branches, bamboo, sawdust, etc., and can also be used for bamboo, thatch, corn stalks, sorghum Stalk and other fiber-like material of the chip.Wood crushers because of its internal structure, crushed the finished product size is very uniform, there is no greater difference in particle size. Working principle The machine uses impact crushing method, the use of internal high-speed operation of the hammer and the fixed ring gear around the relative movement, the material by the hammer collision, friction, get smashed each other. Crushed good material by rotating centrifugal force through the sieve screening into the capture bag. Advantage 1.Hammer crusher with less investment, low energy consumption, high productivity, good economic returns, easy to use and maintenance advantages. 2.Hammer crusher sawdust particle size after crushing small, obvious wood fiber, the material evenly, the quality of finished wood products, low processing costs.
Product Introduction Ring die pellet machine is specially designed for mass industrial production of wood pellets.It is a full set of mechanized production equipment. It can convert biomass raw material and solid waste into energy fuel with high density.wood pellet mill is suitable for various kinds of materials whose moisture content is less than 15%.The machine is fully automatic electric heating, and can adjust the humidity of materials to deal with problems of congestion and not forming. Raw material Raw materials from a wide range of eucalyptus, pine, fruit trees and other wood waste, wheat, soybean meal, corn, rice husk and other crop straw, sawdust, sawdust and other materials. Working principle When the ring-die pellet machine is in operation, the material rotates into the material cavity through the feeding port, and the centrifugal force causes the material to continuously circularly move and adhere to the inner wall of the stamper to form a uniform annular material layer, Constantly rotate the extrusion, making it forced into the ring hole in the molding, and continue to squeeze outwards, gradually by the dial to promote the particles out of the discharge port. Advantage 1. Die legislation, vertical frequency feed, to prevent uneven feeding. 2. The host drive using high-precision gear drive to enhance the wear resistance of gear, particle machine running more smoothly. 3. Double mold, a variety of aperture to meet user requirements of various granulation. 4. Spindle and Siamese hollow shaft made of high quality alloy steel, a substantial increase in wear resistance. 5. Particle molding system bearings are used high-quality silent bearings, longer service life, safer operation. 6 .Automatic timing oil lubrication system to ensure adequate lubrication bearings, more safe and reliable operation.
Product Introduction The whole machine with delivery, into Material, pressure plate, broken one linkage control. In addition can be customized according to customer requirements of various types of wood processing equipment. Synthetic crusher crushed product size similar to the matchbox, but also can adjust the size of the material according to the size of the material, but because of raw materials, are used thickened screen, so the size of the finished product is generally 2-8 cm, belonging to broken wood equipment.  Raw material Comprehensive crusher is a professional crusher used to crush the waste template on the site, bamboo plywood, wood-based panels, plywood and other wood crushing equipment, Machinable width of 1.5 meters, the thickness of 1-30 cm of wood and other scraps. Working principle Comprehensive crusher structure is more complex, the use of hammer broken principle, in front of conveyor belt feeding, feeding port feeder, which has the first crushing system, except the nail system, the second crushing system, exhaust dust system , From the feed to the discharge of the size of the motor in this process a total of seven, belonging to the automatic with a nail removal system crusher. Structural 1, Feed delivery: to be placed plate to be broken wood; 2, Feed roller: feed speed control and keep the plate does not slip and no feed situation; 3, Spiral crusher roll: evenly distributed in the circumferential direction of the roller welding cutter, crushing roller to ensure that the moment in the circumferential direction of the same force; 4, The template is broken with the feed and broken synchronization, to achieve uniform crushing; 5, The feed roller adopts UCK series bearing plus spring compression mechanism, which can be adapted to the different thickness of the plate; 6, feed roller and crushing roller using different power system, easy to control  resistance to wear,one welding time can work continuously for more than 30 hours. Advantage 1, engaging blade, the material completely broken; 2, the choice of special blades, blade hardness is high; 3, strong structure, dense reinforcement plate to ensure the strong box; 4, automatic button control, safe and convenient; 5, safety signs and safety labels to ensure the safety of use;
Product Introduction Garden cutting machine is a set of slices, crushed as one of the crusher, is a branch of garden pruning branch specializing in the production of mobile devices, mainly used for crushing wood into small pieces, crushed raw materials of uniform size and good quality. The device can be equipped with motor or diesel engine according to user requirements. The machine is not only used in landscaping, urban afforestation, fruit tree planting and other fields, but also widely used in furniture factories, wood products and fungus farmers use venues. Raw material The scope of the use of garden tree shredder : trimming under the trunk, leaves, branches, straw can also use this equipment for crushing treatment. Working principle Garden cutting machine with hydraulic compulsory feeding, the loose twigs forced into the crushing chamber, the blades are constantly rotating high-speed cutting, the finished product discharged from the discharge port. Advantage 1. High-speed alloy blade, sharp and durable, stable cutting. 2. Simple structure, durable. 3. Simple operation, high efficiency. 4. Wide range of applications, high safety performance. 5. Easy to move and maintain
Wood chipS boilers for sugarcane production description The DZL/DZH series boiler are the new water-fire tube singel drum coal/wood fired boiler. Eco-friendly and energy-saving product co-developed by our company and famous Harbin institute of Technology and director of Beijing Institute of Light Boiler. 1.Boiler model:DZL/DZH 2.Boiler capacity:1-20ton/h 3.Pressure:1.0Mpa(10bar),1.25Mpa(13bar),1.6Mpa(16bar),2.5Mpa(25bar) 4.Steam temperature:184 °c,194c, 204c,226c(As long as below 226c,we can do it) 5.Fuel:coal,biomass 6.Structure:horizontal water-fire tube, single drum 7.Type:There are two types.One is DZL chain grate stoker automatic feeding fuel and removing dregs type. Another is DZH hand operated moving grate type which needs labour to feed fuel and remove the dregs. 8.Application:Medicine, chemical, light industry, textile, building material, cultivation, food and beverage, plastic foam, printing, dyeing and washing, rubber processing, paper products,wood processing, hotel, clothing and leather manufacturer etc. The features of Wood chipS boilers for sugarcane production Screw thread pipe Function: strengthen heating transfer,reduce the quantity of pipe and decrease the shell size Purpose: save steel material,no dust,improve flexibility,prevent tube plate cracking Convex tube plate Function: improve tube plate flexibility,so as to reduce the heating stress of welded sew at the pipe end Purpose: prevent tube plate cracking, cancel bracing,simplify the structure Optimized design CAD Function: Choose the best furnace from dozens of options Purpose: improve economical efficiency New pattern of furnace arch Function: strengthen the combustion ,strong adaptability of coal quality Purpose: Improve combustion efficiency Smoke and dust separator chamber Function: Separate smoke and dust according to inertia Purpose: reduce the original effluent concentration of soot Return water eject to the high temperature tube plate Function: Improve the flow rate of high temperature tube plate and prevent subcooled boiling Purpose: prevent the tube plate cracking Large size of simple circulation loop drop pipe and lower set box Function: Increase the flow rate of water on water cooling wall in order to prevent subcooled boiling Purpose: To prevent pipe explosion,Increase the reliability of water cycle
Introduction of wood rice husk pellet machine Vertical ring die pellet mill is one kinds of production machine to process eucalyptus, pine, birch, poplar, Fruit tree and crop stalk, bamboo, shaving, sawdust into biomass fuel. Homemade wood rice husk pellet machine feature: 1.Stand mold, vertical feed, no arch camber, good heat radiation 2.Mold static vertical installation, easy fixed, stable performance 3.Roller rotation, make the material produce centrifugal force, well-distributed 4.Double layer mold, up and down dual-use, decreasing cost and increasing benefit 5.With high precision cylindrical in volute helical gear drive directly, transmission efficiency above 98%
Introduction of wood rice husk pellet machine Vertical ring die pellet mill is one kinds of production machine to process eucalyptus, pine, birch, poplar, Fruit tree and crop stalk, bamboo, shaving, sawdust into biomass fuel. Homemade wood rice husk pellet machine feature: 1.Stand mold, vertical feed, no arch camber, good heat radiation 2.Mold static vertical installation, easy fixed, stable performance 3.Roller rotation, make the material produce centrifugal force, well-distributed 4.Double layer mold, up and down dual-use, decreasing cost and increasing benefit 5.With high precision cylindrical in volute helical gear drive directly, transmission efficiency above 98%
It's also called wood chipper machine , which is an ideal equipment of processing the raw materials including wood branch, log, bamboo into wood chips once. Feature of industrial disc wood chipper : 1. Specially designed for round logs, square blocks, wood staff, wood pieces and chips. 2. Widely raw materials can be any moisture and any shape. Advantages of disc wood chipper machine: 1. Easy operation 2. Low and simple maintenance 3. Long working life and low noisy 4. Wood chipper would be the best choice for dealing with wood scraps. The wood chipper machine can process pine, miscellaneous tree , wood fir , because the structure is compact, less covering area, good quality of slice, low power consumption.
