ELM 327 USB ( FTDI chip + Power Protection Chips) Functions: Read diagnostic trouble codes, both generic and manufacturer-specific, and display their meaning (over 3000 generic code definitions in the database) Clear trouble codes and turn off the MIL ("Check Engine" light) Display current sensor data, including Engine RPM Calculated Load Value Coolant Temperature Fuel System Status Vehicle Speed Short Term Fuel Trim Long Term Fuel Trim Intake Manifold Pressure Timing Advance Intake Air Temperature Air Flow Rate Absolute Throttle Position Oxygen sensor voltages/associated short term fuel trims Fuel System status Fuel Pressure Many others Features: OBD SCAN is the newly developed wireless scan tool. It supports all OBD-II protocols Automatic SAE J1850 PWM(41.6Kbaud) SAE J1850 VPW(10.4Kbaud) ISO9141-2(5 baud init,10.4Kbaud) ISO14230-4 KWP(5 baud init,10.4 Kbaud) ISO14230-4 KWP(fast init,10.4 Kbaud) ISO15765-4 CAN(11bit ID,500 Kbaud) ISO15765-4 CAN(29bit ID,500 Kbaud) ISO15765-4 CAN(11bit ID,250 Kbaud) ISO15765-4 CAN(29bit ID,250 Kbaud) A.SAE J1939 CAN(29bit ID,250*Kbaud) B.USER1 CAN(11*bit ID,125*Kbaud) C.USER2 CAN(11*bit ID,50*kbaud) Default settings(user adjustable) Specifications: Output Protocol: RS232 to bluetooth Frequancy: 38400 Size: 88*46*25 Voltage: 12V Current: 45mA Bluetooth: 10M Supported platform: Andriod, Symbian, Windows Mobile, palm, pc, pocket pc.
ELM 327 bluetooth OBD2 CAN BUS Scanner OBDII Wireless Diagnostic Tool Functions: Read diagnostic trouble codes, both generic and manufacturer specific, and display their meaning (over 3000 generic code definitions in the database) Clear trouble codes and turn off the MIL ("Check Engine" light) Display current sensor data, including Engine RPM Calculated Load Value Coolant Temperature Fuel System Status Vehicle Speed Short Term Fuel Trim Long Term Fuel Trim Intake Manifold Pressure Timing Advance Intake Air Temperature Air Flow Rate Absolute Throttle Position Oxygen sensor voltages/associated short term fuel trims Fuel System status Fuel Pressure Many others Features: OBD SCAN is the newly developed wireless scan tool. It supports all OBD-II protocols Automatic SAE J1850 PWM(41.6Kbaud) SAE J1850 VPW(10.4Kbaud) ISO9141-2(5 baud init,10.4Kbaud) ISO14230-4 KWP(5 baud init,10.4 Kbaud) ISO14230-4 KWP(fast init,10.4 Kbaud) ISO15765-4 CAN(11bit ID,500 Kbaud) ISO15765-4 CAN(29bit ID,500 Kbaud) ISO15765-4 CAN(11bit ID,250 Kbaud) ISO15765-4 CAN(29bit ID,250 Kbaud) A.SAE J1939 CAN(29bit ID,250*Kbaud) B.USER1 CAN(11*bit ID,125*Kbaud) C.USER2 CAN(11*bit ID,50*kbaud) Default settings(user adjustable) Specifications: Output Protocol: RS232 to bluetooth Frequancy: 38400 Voltage: 12V Current: 45mA Bluetooth: 10M Size: 88*46*2 Supported platform: Andriod, Symbian, Windows Mobile, palm, pc, pocket pc.
Best Car Jump Starter Environmental Adaptability Why buy car jump starter from us? 1. when the car need emergency start because of battery power shortage, ordinary mobile power can not provide the enough high current car starts; 2. can be used as mobile power electronic devices 3. can be used as LED lights, lighting needs to provide multiple modes Second, environmental adaptability Standard Operating Temperature: -20 degrees +60 degrees ---- Optional Ultra-low temperature operating temperature: -40 ---- + 60 degrees Third, the large-capacity Standard two kinds of capacity 10000mAh, 12000mAh Fourth, safe and reliable Configuring multiple protection circuit to ensure product safety and reliability.
Hot Selling Fiat ECU Scan Adaptors Car ECU Scanner with Best Price Why Buy diagnostic cables/connectors from us? We are professional factory for cables. 12 years experience make cables and We offer best price in china. We always use best quality plastic and other materials,not use bad plasticand cable usage is short and do'nt look decent. We make all kinds of cables,almost full range of diagnostic cables. We can make cables as your design and any requirements,any color,any length available. We can make your own pinout for u for free. We test every single pc before we send to clients,almost ZERO bad feedback. we offer plenty cables in short time, thousands pcs can be made in a few days. We stock plenty to avoid any shortage,not like trade companies,take money first and let clients wait. A Life-time warranty. Description: Fiat Ecu Scan Adaptor Fiat Connector OBD2 16Pin OBD Cable for Fiat Four Colors (4 Pieces/ Set). We can do any pinout as clients offered . We can do any design as clients offered. Specifications: Type: OBD2 Cable Applicable Models: Most of branded of cars, OBD Cars Voltage: 12V Power: 24W Certification: CE, SGS Material: Plastic Color: Four colors OEM: Yes Shipping ways: China post, DHL, UPS, Fedex, TNT, EMS, HongKong post, etc Package List: 4pcs/set x Fiat Cables
Latest Version OBD Diagnostic Scanner for Opel OP-COM V1.45 with Best Price Functions: 1. It covers almost all Opel cars, even new cars with CAN-BUS based diagnostic, such as Vectra-C, Astra-H, Zafira-B. 2. The program lets you to read out and clear fault codes, shows you live data, lets you to perform output test, and supports remote, and key programming. 3. The program supports many control units, like Engine, Automatic Transmission, ABS, Airbag, Engine Cooling module, Instrument Cluster, Electronic Climate Control, Body Control Unit, just to name a few examples. 4. Since Opel uses many pin in the OBD connector, the diagnostic interface works as a multiplexer, and selects the appropriate pin for communication. PIN3, PIN7, PIN8, PIN12 = Serial Link (ISO9141, KW81, KW82, KWP2000) 5. Fault codes will be shown with all available information: Full fault code text description Full status information (Present, Not present, Intermittent) 6. You can print out, save, or copy the fault codes to any other application.From the fault codes window, you can go directly to the measuring blocks window. 7. The program shows you measuring block information on many control module, you can choose anything from the list on your own. 8. The program is capable of showing 8 measuring block parameter simultaneously. The sample rate is depends mostly on the communication protocol. For example, older system, like Omega-B X 25 DT Engine (ISO-9141-2) can be very slow, during communication, while newer Multec, or Bosch units are faster (using KWP-2000), and the newest CAN based control units are very fast! You can also run output tests on many controllers. PIN6-PIN14 PIN3-PIN11 PIN1 HSCAN - Dual-wire, High Speed CAN-BUS, 500 kbps MSCAN - Dual-wire, Medium Speed CAN-BUS, 95 kbps SWCAN - Single-wire, Low Speed CAN-BUS, 33.3 kbps. 9. You will get a feedback on the state of the activated output. This will helps you to find the failed.components more easily.With DIGIOBD OP-COM, you can learn keys to immobiliser, and remote keys to the central door locking. 10. You can also reset, and program the following immobiliser related items: ECM, BCM, IPC. You will need the vehicle security code, which can be found on the CAR-PASS. You can also reset, and program the Service interval reminder on Astra-G, Zafira, Corsa-C, Meriva You can code SAB6, and SAB8 airbags with the software.
Car cables full 8 pcs / set for Autocom TCS CDP Pro cables obd2 connect adapter Why Buy diagnostic cables/connectors from us? We are professional factory for cables. 12 years experience make cables and We offer best price in China. We always use best quality plastic and other materials, not use bad plasticand cable usage is short and dont look decent. We make all kinds of cables,almost full range of diagnostic cables. We can make cables as your design and any requirements,any color, any length available. We can make your own pinout for u for free. We test every single pc before we send to clients, almost ZERO bad feedback. We offer plenty cables in short time,thousands pcs can be made in a few days. We stock plenty to avoid any shortage,not like trade companies, take money first and let clients wait. A Life-time warranty. Description: The OBDII adapter cable full set for cars is compatible with OBDII diagnostic tools such as the Autocom CDP, TCS CDP Pro, MultiDiag Pro+ and Delphi DS150E diagnostic tools. Also With those cables you can do some . old cars, such as BENZ 38PIN or BMW 20PIN etc. The set includes a total of 8 car cables. Package list: 1pc PSA 30P Cable 1pc PSA-2P Cable 1pc Adi 2P+2P Cable 1pc BENZ-38P Cable 1pc BMW 20P Cable 1pc OPEL 10P Cable 1pc FIAT 3P Cable 1pc Power Cable
8 Pieces / Set OBD2 Truck Cables For Autocom CDP Pro Truck Diagnostic Interface Tool Why Buy diagnostic cables/connectors from us? We are professional factory for cables. 12 years experience make cables and We offer best price in china. We always use best quality plastic and other materials,not use bad plastic and cable usage is short and dont look decent We make all kinds of cables,almost full range of diagnostic cables. We can make cables as your design and any requirements,any color,any length available. We can make your own pinout for u for free. We test every single pc before we send to clients,almost ZERO bad feedback. we offer plenty cables in short time,thousands pcs can be made in a few days. We stock plenty to avoid any shortage,not like trade companies,take money first and let clients wait. A Life-time warranty. Description: 8 Piece Truck Cables OBD2 Adapter Truck Diagnostic CableThe OBDII adapter cable set for trucks is compatible with Autocom CDP, TCS CDP Pro, MutliDiag Pro+ and Delphi DS150E diagnostic tools. The set includes a total of 8 truck cables. Packaging list: 7 pin Knorr,Wabco Trailer Cable 12 pin MAN Cable 37 pin MAN Cable IVECO 30P Cable SCANIA 16P Cable MB-14P Cable Renault 12P Cable VOLVO 8P Cable
FarmScan® M30 is new small in size but big in functionality and features. Modern hand-held designed exclusively for veterinary practitioners, who need an economic and simple ultrasound for the purpose of swine and ovine pregnancy diagnostics. Feature: Highly cost effective device Quick and accurate measurements with digital technology Easy to use, learn, and teach Precision aiming ability via ergonomically designed console and probe Easy-to-use, handheld probe Color LCD screen for easy reading Brightness controls Portable, Reliable and durable design Two batteries provided for continuous use Two-year warranty Advance Features¡êo 14 hours for continuous operation, meeting a long day scanning needs(2 batteries); light weight only 325g ,and modern ergonomics designing make it comfort to use; advanced full digital core technology to obtain high quality images, ensure accurate pregnancy check at early stage; 128 frames permanent storage, without loss of image when powered off; simple, yet very reliability and resistant, suitable for breeding farm harsh field conditions; waterproof and dustproof detachable probe, can be easily cleaned by flowing water; 19th day in pigs and 25th in sheep pregnancy diagnosis, especially if the breeder is very experienced. Dimension: (L)24cm X (W)12cm X (W)5cm Weight: 325G
RKU 10 Veterinary Ultrasound Scanner Target customer: Main end users: big farmers and veterinary . (e.g. ranchers who raise more than 1,000 cattle) . Application: RKU 10 can be widely used in normal ultrasound diagnosis like abdomen and pregnancy. Main marketoobig animals regnancy check and follicular aspiration (Bovine, equine, ovine, canine, feline, goat, swine and llama). Feature: 1.1kg weigh. Smart and light. High-capacity lithium Battery ,more than 6 hours work. sunshine cover, suitable for use in outdoor strong sunshine. Available for left/right hand alternative use, eliminating operate fatigue. Multiple use method: hand-held, chest hanging, back hanging , waist hanging, ect. Optional professional ultrasound goggle, convenient for outdoor use, meet different need. Have soft rubber coat, splash-proof, dust-proof. 2 kinds filter function, 7 kinds compress curve, 100 frames image permanent storage, 256 frames cine loop, Automatically calculate the Back fat and Lean percentage of swine. Standard configuration Main unit: 1 pc 6.5MHz linear rectal probe : 1 pc Power adapter: 1 pc Internal lithium battery : 1 pc Soft rubber coat: 1 pc Sunshine cover : 1 unit (A,B,C three sections adjustable) Black plastic suitcase : 1 pc Base Charger, belt, probe socket spatula: 1 pc for each. Optional Configuration: Probeoo 4.0Mhz multi-frequency convex rectal Probe 6.5MHz multi-frequency micro-convex probe 3.5MHz multi-frequency convex probe 6.5MHz multi-frequency trans-vaginal probe 7.5MHz multi-frequency linear probe 3.5MHz multi-frequency micro-convex cardiac probe 3.5MHz loin muscle probe Thermal printer o¨¬P93W-So© Color laser printero¨¬Specified modelsooHP Color LaserJet CP1515n|HP Color LaserJet CP1525no© Lithium Batteryo¨¬5200mAHo© Leather Case saddlebag
Superfine needle tip wire pen cable for universal digital multimeter, safety grade 1000V 10A 20A multimeter lead probe, super-pointed multimeter lead probe pen for mobile phone logic board repair tool. 1000V 20A /10A Universal Superfine Lead Probe Needle Tip Wire Pen Cable For Digital Multimeter [ Optional Types ] : Option 1: 1000V 10A Superfine Needle Tip, Gold Option 2: 1000V 20A Superfine Needle Tip, Gold Product Specifications : Red: positive Black: negative Cable length: 88cm / 34.3" Total length: 106cm / 41.3" Professional test maximum voltage: 1000V 20A/10A Universal superfine pen for digital multimeter: 1000V 20A / 10A, test lead probe cable SMD SMT needle tip Product Features : Easy to read: "+" & "-" signs near probes (Red -''+''; Black - ''-'' ) Made of soft silicone, -50 ~ 200 still work fine, not easy to knot, not broken. Our Test Lead has one pair of red and black comfort grip probes with flexible insulated test leads With distinctive comfort grip probes, they are heat and cold resistant with safety ratings up to CAT II 1000 V Ultra-sharp Probe Tips Gold-plated probe tips are sharp and hard, easy to reach small contact points on high-density boards Compatible with any meter equipped with shrouded banana input jacket Easy access to ICS, LED, SMD, etc. Package List : 1 Pair * Multimeter Probe Lead
Switch Probe Pogo Pin SWP164 for Electronic Test Switching Probes is a kind of functional probes. They are used to determine the correct location of a terminal in a connector. They can also be used to determine the presence of nonconductive components, etc. Their application field is mainly as below Wire harness connector PCB component detection Door open-close switch Fixture component detection Automation process sensing Position and retention force Below switching probe we will introduce is SWP164. Its diameter is 1.64 mm and total length is 44.65 mm. As usual, switching probes do not entail very high currents, and this model SWP260 can work with the current up to 3 A. The typical maximum contact resistance of this model SWP164 is 160 m. The materials used for the construction of switching probes are different for each component: The barrel is made of brass. Subsequently gold plated during the galvanic plating phase. The spring is made of gold plated music wire. The plunger is made of Beryllium Copper, then gold and nickel plated. The insulating sleeve is made of POM For details of SWP164 switching probe, please check below parameters. Technical Specifications Recommended Current Rating: 3 Amps, continuous Contact Resistance: 160 milliohms, maximum Full Stroke: 5 mm Rated Stroke: 3.3 mm Spring Force: 130 gf (4.5 oz) Normal Condition: Disconnecting between Plunge 1 and Plunger 2 Press down 1 mm: Continuity between Plunger 1 and Plunger 2 Materials Contact Barrel: Brass, Au on Ni Plated Spring: SWP, Au on Ni Plated Plunger 1: Beryllium Copper, Au on Ni Plated Plunger 2: Beryllium Copper, Au on Ni Plated Insulating Sleeve: POM Advantages of this switching probe Reliable performance Low cost of test Best yield Our company are also able to change the head shape, total length and diameter, etc., of our switching probes to facilitate their use in different applications. The pitch of installation of switch probes depends on your specific needs. Company Information Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Test Probe Pogo Pin PL50 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PL50 series here. Its test center is 50 mil, namely 1.27 mm. The diameter is 0.68 mm and the total length is 27.53 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. There are roughly four types of receptacles, namely CR, VCR, SC, VSC, CRW and VCRW, to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 50 milliohms Mounting Hole Size: Diameter 0.95 mm Full Stroke: 3.7 mm Rated Stroke: 2.54 mm Spring Force: 28/56/85 gf (1/2/3 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper/SK4, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Pogo Pin High-current Probe P350(300) Series for Electronic Test Cable harness test probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. Their standard and requirements are higher than other series of test probes. They can be divided into screw-thread harness test probes, cable harness switch probes, non-screw-thread harness test probes, position-limited harness test probes and cable harness high-current probes, etc. High-current probes can withstand high current and high temperature in the tests. They are mainly applied to the in-circuit test field of high temperature and high current environments. High-current probes manufactured by Centalic mainly include P203, P264, P265, P350 and P420, etc. There is a fixed schedule for mass production of P350(300). This probe can withstand the current up to 24 Amps. And its typical maximum contact resistance is 70 milliohms. The materials used for the construction of this high-current test probe are different for each component: The barrel is made of brass. Subsequently gold and nickel plated during the galvanic plating phase. The spring is made of gold plated music wire. The plunger is made of beryllium copper, then gold and nickel plated. For details, please check parameters in below table. Technical Specifications Recommended Current Rating: 24 amps, continuous Contact Resistance: 70 milliohms, max Full Stroke: 5.5mm Rated Stroke: 3.6 mm Spring Force: 340 gf at load 3.6 mm Company Information: Centalic Technology Development Ltd. was founded in 1980.Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Semiconductor Test Probe Pogo Pin SCPC035 Series for IC Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPC035 we will introduce is 0.35 mm in barrel diameter and 7.7 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 2.5 amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1 mm. But it is better to be pressed at a distance of 0.5 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.5 mm, the loaded force is about 18 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel Phosphor Bronze, Au on Ni Plated Bottom Plunger Beryllium Copper, Au on Ni Plated Top Plunger Beryllium Copper, Au on Ni Plated Spring SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating 2.5 amps Contact Resistance 100 milliohms max Bandwidth 5.8 GHz at -1dB Inductance 1MHZ at -0.01039 uH Captance 1MHZ at 2.35287 uF Specifications: Full Stroke 1 mm Rated Stroke 0.5 mm Spring Force 18 �±5 gf at load 0.5 mm Mechanical Life about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Gold-plated Probe Pogo Pin PE100(90) Series for In-circuit Test In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PE100(90) series here. Its test center is 100 mil. The diameter is 1.36 mm and the total length is 34 mm. Various tip styles, for example, A, B, U, H, K, L, BK, etc., are available for test probes. There are roughly three types of receptacles, namely CR, SC and WW to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 2.54 mm (100 mil) Current Rating: 3 Amps, continuous Contact Resistance: 30 milliohms Mounting Hole Size: Diameter 1.75 mm Full Stroke: 6.5 mm Rated Stroke: 4.3 mm Spring Force: 284 gf (10 oz) Materials Receptacle: Brass, Gold Plated Contact Barrel: Brass, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Double-Sided Spring Pogo Pin Test Probe SCPC031 Applied to Chip Inspection Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPC031 we will introduce is 0.31 mm in barrel diameter and 6.7 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The top plunger is made from SK4 plated with nickel and gold. The inner spring is made from music wire plated with gold and nickel. This probe pin could withstand the current up to 1.5 amps. The typical maximal contact resistance is about 150 milliohms. The plunger can be pressed at a distance of up to 1 mm. But it is better to be pressed at a distance of 0.65 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.65 mm, the loaded force is about 25 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Phosphor Bronze, Au on Ni Plated Bottom Plunger: Beryllium Copper, Au on Ni Plated Top Plunger: SK4, Au on Ni Plated Spring: SWP-A/B, Au on Ni Plated Electronic Specification: Current Rating: 1.5 amps Contact Resistance: 150 milliohms max Bandwidth: 7.5 GHz at -1dB Inductance: 1MHZ at -0.05856 uH Captance: 1MHZ at 0.434274 uF Specifications: Full Stroke: 1 mm Rated Stroke: 0.65 mm Spring Force: 25�±5 gf at load 0.65 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
In-circuit Test Probe Pogo Pin P156 Series for PCB Assembly Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PQ156 series here. Its test center is 156 mil. The diameter is 2.36 mm and the total length is 33.79 mm. Various tip styles, for example, B, C, G, J, K, L, T, etc., are available for test probes. There are roughly four types of receptacles, namely CR, SC, WW and WW-L, to fit each test probe For details, please check below parameters. Technical Specifications Recommended Minimum Center: 3.96 mm (156 mil) Current Rating: 5 Amps, continuous Contact Resistance: 50 milliohms Mounting Hole Size: 2.75 mm Full Stroke: 6.35 mm Rated Stroke: 4.32 mm Spring Force: 113/198/255/285 gf (4/7/9/10 oz) Materials Receptacle: Phosphor Bronze, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring: Music Wire, Gold Plated Plunger: Beryllium Copper, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals.
Electronic Test Probe Pogo Pin PC50 Series for PCBA Inspection In-circuit test probes are mainly used for testing electrical performance of in-circuit components on PCB and the connection between circuit networks. It could quantitatively measure components such as resistors, capacitors, inductors, crystal oscillators, and perform functional tests of diodes, triodes, optocouplers, transformers, relays, operational amplifiers, power supply modules and integrated circuits. We will introduce in-circuit test probe PC50 series here. Its test center is 50 mil, namely 1.27 mm. The diameter is 0.78 mm and the total length is 43.2 mm. Various tip styles, for example, H, S, T, E, C, U, G, etc., are available for test probes. There are roughly four types of receptacles, namely CR, SC, SW and CRW, to fit each test probe. For details, please check below parameters. Technical Specifications Recommended Minimum Center: 1.27 mm (50 mil) Current Rating: 3 Amps, continuous Contact Resistance: 60 milliohms Mounting Hole Size: 1 mm Full Stroke: 6.4 mm Rated Stroke: 4.3 mm Spring Force: 100/110/150/200 gf (3.6/4/5.4/7.2 oz) Materials Receptacle: Phosphor Bronze, Gold Plated Contact Barrel: Phosphor Bronze, Gold Plated Spring:� Music Wire, Gold Plated Plunger: SK4, Nickel Plated or Gold Plated Company Information Centalic Technology Development Ltd. was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals.
High-current Probe Pogo Pin P265 Series for Electronic Test Cable harness test probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. Their standard and requirements are higher than other series of test probes. They can be divided into screw-thread harness test probes, cable harness switch probes, non-screw-thread harness test probes, position-limited harness test probes and cable harness high-current probes, etc. High-current probes can withstand high current and high temperature in the tests. They are mainly applied to the in-circuit test field of high temperature and high current environments. High-current probes manufactured by Centalic mainly include P203, P264, P265, P350 and P420, etc. There is a fixed schedule for mass production of P265. This probe can withstand the current up to 24 Amps. And its typical maximum contact resistance is 50 milliohms. The materials used for the construction of this high-current test probe are different for each component: The barrel is made of brass. Subsequently gold and nickel plated during the galvanic plating phase. The spring is made of gold plated stainless steel. The plunger is made of beryllium copper, then gold and nickel plated. For details, please check parameters in below table. Technical Specifications Recommended Current Rating: 24 amps, continuous Contact Resistance: 50 milliohms, max Full Stroke: 5.3 mm Rated Stroke: 3.5 mm Spring Force: 220 gf (7 oz) at load 3.5 mm Company Information: Centalic Technology Development Ltd. was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
Double-sided Spring Pogo Pin Test Probe SCPC058 for IC Test Semiconductor test probes are usually called double-ended pogo pins. Common tip styles include B, J, J1, U, U1, etc. All of the probes are extremely thin and miniature, however, the requirement for their test accuracy is very strict. They are mainly applied to the fields of semiconductor tests and frequency tests of communication devices, for example, the frequency tests of mobile phones, walkie-talkies, computers, etc. This product SCPC058 we will introduce is 0.58 mm in barrel diameter and 8.85 mm in total length. It can be applied to the tests of products which requires relatively high accuracy, for example frequency tests of semiconductor and communication devices. Developed and manufactured on our own, this product takes the lead in the test industry. Our complete production lines can also meet the needs for mass production. The barrel of this double-ended pogo pin is made from phosphor bronze plated with gold. The bottom plunger is made from beryllium copper plated with nickel and gold. The same is with the top plunger. The inner spring is made from SUS304 plated with gold and nickel. This double-sided spring pogo pin could withstand the current up to 4 amps. The typical maximal contact resistance is about 100 milliohms. The plunger can be pressed at a distance of up to 1.2 mm. But it is better to be pressed at a distance of 0.8 mm at most in working environments. Otherwise, the spring will probably be damaged severely under constant pressure. When the plunger is pressed at a distance of 0.8 mm, the loaded force is about 35 gf, which fluctuates to a tolerance. For details, please check parameters in below table. Materials (plated) Barrel: Phosphor Bronze, Au on Ni Plated Bottom Plunger: Beryllium Copper, Au on Ni Plated Top Plunger: Beryllium Copper, Au on Ni Plated Spring: SUS304, Au on Ni Plated Electronic Specification: Current Rating: 4 amps Contact Resistance: 100 milliohms max Bandwidth: 9.3 GHz at -1dB Inductance: 1MHZ at -0.02158 uH Captance: 1MHZ at 1.4027 uF Specifications: Full Stroke: 1.2 mm Rated Stroke: 0.8 mm Spring Force: 35�±7 gf at load 0.8 mm Mechanical Life: about 200000 cycles Company Information: Centalic Technology Development Ltd was founded in 1980. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big-current probes, spring probes, universal complex test probes, wafer probes, and so on.
