Digital Rail Head Wear Gauge is is mainly used to measure the vertical wear and lateral wear of the rail.The reasonable design makes it light,convenient operation and intuitive reading.
Digital Rail Frog Wear Gauge is used to measure vertical wear value of frog point rail and wing rail at any sections.Also could be used for measuring decrease value of point rail relative to wing rail.
Analogue track gauge is used for measuring the railway track gauge,check rail gauge, back to back distance,super-elevation. It is Suitbale for railway speed not greater than 160km/h.Traditional compass is more easier for rail workers to accept and operate.Light weight structure is convenient to carry.
Specification Model LJ-ZJC-30 Type L Square Ruler Material Stainless Steel Dimensions (L x W x H) (mm) 300*130mm Scale 1mm Length 300 mm
lightweight abrasive rail saw lightweight abrasive rail saw is a railway maintenance tool. It not only cuts rails with high speed and high quality, but also has low wear cutting discs. It is locked by rail clamps. It has a simple structure, light weight, safety and easy movement. It is suitable for maintenance, repair of broken rails of seamless tracks, and cutting of steel rails in long rail weldin
GM-2.2 Electric Rail Grinding Machine GM-2.2 electric rail grinding machine for 43kg / m-75kg / m rail weld, uneven joints, rail side fat side, rail welding and other parts of the grinding. It has the advantages of high operation efficiency, good grinding quality, easy operation and convenient operation of the upper and lower roads. It is an essential tool for overhaul, maintenance and repair of railway.
Railway Track Square Railway square ruler is a special measuring tool used to check the right Angle dislocation of railway track. Benefits 1. High accuracy:The structure is uniform, the linear expansion coefficient is minimal, the internal stress completely disappears, the ruler body is stable and does not deform. It can keep the perpendicularity between the ruler body and the rail surface â?¤0.05mm 2. Long service life: It is made of aluminum alloy, resistant to acid and alkali corrosion, not easy to rust, not easy to stick to dust, no need to grease, easy and simple maintenance 3. Stable insulation performance: one end is the insulated electric board and the other end is the plastic insulation sleeve. It can ensure the operating safely. 4.Customizable 5.The Measuring head is made of bearing steel: High hardness, not easy to rust and deformation 6.Multifunctions 1)Measure the switch angle steel whether is square when installed 2)Measure the internal lock switch parts whether is square when installed 3)Measure the switch rail whether creeping 4) Measure the sleeper whether square when installed.
Rail wave grinding machine The GBM-7.6 rail wave abrasion grinding machine is a professional machine used for the wave abrasion and grinding of the rail top. This machine is suitable for various rails of 43~75kg/m.
Product Description YDT-900 Hydraulic Vertical Rail Bender This machine is used for the bending operation of railway seam lines and welded joints of seamless tracks and other low-collapsed parts of steel rails. It can also be used as vertical bending and supporting equipment in the laying of seamless tracks; suitable for all types Rails. The machine has simple structure, convenient operation, safe operation and easy maintenance. It is an effective tool for rectifying rail joint problems.
Product Description Hydraulic rail bending machine rail bender Hydraulic rail bending machine also called hydraulic bend machine, is rail installation maintenance when a special tool to bend the rail operations. Hydraulic bend machine is a dedicated to laying railway line in tunnel mining slope level elevation changes at the scene of the track-laying for below 50 kg/m or light rail vertical bending or adjustment. Hydraulic rail bending machine designed by the principle of hydraulic transmission and leverage, using static pressure on curved track rail horizontal and vertical curve or straight rail operations. Product Parameters Model YZG- 550 type hydraulic rail bending machine Rated force 550KN Rated pressure 52Mpa Size 1100 700 400 mm Whole machine weight 125kg
CNC Rail profile grinding machine This rail profile grinding machine is mainly used for forming and grinding operations of railway rail welding joints and rail surface repairs. The development and application of the CNC feed unit realizes the intelligent control of the grinding wheel feed. Significantly improve the profiling accuracy and polish
GM-2.2 Electric Rail Grinding Machine GM-2.2 electric rail grinding machine for 43kg / m-75kg / m rail weld, uneven joints, rail side fat side, rail welding and other parts of the grinding. It has the advantages of high operation efficiency, good grinding quality, easy operation and convenient operation of the upper and lower roads. It is an essential tool for overhaul, maintenance and repair of railway. Model GM-2.2 Type Electrict Rail Profile Grinder Material Stainless Steel Dimensions (L x W x H) (mm) 1500mm*630mm*760mm Electric motor Type:Y2-Y90L-2 Voltage: 380V three phase Rpm:2840r/min Power:2.2kW Grinding wheel 125*65*M20 Spindle speed 2840r/min Wheel distance 1000mm Wheel stroke 50mm Weight 54kg
Railway Track Square Railway square ruler is a special measuring tool used to check the right Angle dislocation of railway track. Benefits 1. High accuracy:The structure is uniform, the linear expansion coefficient is minimal, the internal stress completely disappears, the ruler body is stable and does not deform. It can keep the perpendicularity between the ruler body and the rail surface â?¤0.05mm 2. Long service life: It is made of aluminum alloy, resistant to acid and alkali corrosion, not easy to rust, not easy to stick to dust, no need to grease, easy and simple maintenance 3. Stable insulation performance: one end is the insulated electric board and the other end is the plastic insulation sleeve. It can ensure the operating safely. 4.Customizable 5.The Measuring head is made of bearing steel: High hardness, not easy to rust and deformation 6.Multifunctions 1)Measure the switch angle steel whether is square when installed 2)Measure the internal lock switch parts whether is square when installed 3)Measure the switch rail whether creeping 4) Measure the sleeper whether square when installed.
Rail Gap Gauge Rail Gap Gauge is used for measuring the distance between two adjoining rails Benefits: Joint Gap Measuring Device shape: similar to carrot, tapered. This product is made of stainless steel , long service life. Easy to operate and easy to carry Model NW-BB Type Gap Gauge Material Stainless Steel Dimensions (L x W x H) (mm) 35*15*5cm Measure range 5-30mm Material Stainless steel MOQ 50 Pieces
Rail Thermit Welding Thermite welding is a track connection construction process with mature technology, simple, convenient, fast, and high-quality construction.Rail thermite welding is the thermite flux composed of aluminum powder, iron oxide and other metal additives in a special crucible, and a high temperature match is used to ignite the thermite reaction. During the reaction, a large amount of heat is released and the molten alloy mixture reacts to form.Because of its high density, molten steel sinks below, the slag generated by the reaction is relatively light and floats on the upper part, and the molten steel is filled with sand in a short time.At the same time, the aluminum hot molten steel itself acts as a filler metal, crystallizes and cools together with the molten steel rail, and the two steel rails form a whole.
Rail frog and switch grinding machine NCM-5.1 frog and switch grinding machine is specifically designed for grinding operations through switch and crossings and either side of the rail head. The rail grinding device of the machine can be tilted by 30�?�° from the vertical direction to the left and right, and the position of the grinding wheel can be adjusted along the vertical and horizontal directions So that the grinding device of the machine can work very accurately in the narrow space between the rails. The frog and switch grinding machine adopts the pull rod transverse feed mode, which is easy for the operator to grasp the feed force and improve the grinding quality and efficiency.
Contact rail gauge for METRO measurement The contact rail gauge is a gauge for measuring the parameters of the subway contact rail. Measurement parameters can be customized according to customer requirments,detachable and easy to carry. the main ruler body use high strengthsquare tube aluminum alloy. advantages:precise measurement,new style,reasonable design.
Rail Opening Gauge JG-KC01 Rail opening gauge is mainly used for measuring turnout opening and offset gauge. It can be used for electrical maintenance, overhaul, engineering survey and other related department line operation.The instrument has fast measuring speed and easy to use. It can be used in day or night. Specification Model JG-KC01 Type Rail Opening Gauge Material Stainless Steel Dimensions (L x W x H) (mm) 50*3*5cm Opening measure range 0-350mm Offset measure range 0-350mm Accuracy ±0.25mm Working temperature -30~+55 Length Size 56cm
Track Jacks Track jack a device for raising railway track during ballasting or other track operations. Mechanical track jack is the simplest & sturdiest types of the jacks and widely used in Oil Fields, Railway Track Work,Ship Yards, Mining Operation, Construction &Heavy Duty Industrial Maintenance & Establishments. These Track jacks can be used to lifting both on down and up strocks. They're not only be lowered tooth by tooth but also can be made to tripped off by just moving the trip control.
Railway Brake Shoes Friction buffer stops for mainline person and goods traffic railways are especially designed to withstand an impact with large masses with max. speeds of 25 km/h. The track systems and the used locomotives or cars in addition to their buffer geometry determine the type and design of the corresponding solution. Friction buffer stops that are also able to withstand the permanent stress in shunting operations are what characterise. A buffer stop or bumper is a device to prevent railway vehicles from going past the end of a physical section of track. The design of the buffer stop is dependent in part upon the kind of couplings that the railway uses, since the coupling gear is the first part of the vehicle that the buffer stop touches. The purpose of a friction buffer block is to secure the track end and its direct surroundings as well as the rail vehicles themselves. If the brakes fail, the buffer stop should be designed to decelerate the vehicle safely and in controlled manner until it stops. Specification Model LJ-TX Type Railway Brake Shoes Material Stainless Steel Dimensions (L x W x H) (mm) 300*300*150mm
