Garnet Stone *Price: 1.55$ per kg (155$ per ton) *Different Colors *Different Sizes *MOQ: 10 000 tons *Shipment servise , will be shipped after payment Contact for more information
Hammer head is an accessory on the hammer head assembly, installed on the knife tooth seat, mainly in direct contact with coal, used for crushing coal. Hammer head is an accessory on the hammer head assembly, installed on the knife tooth seat, mainly in direct contact with coal, used for crushing coal. Hammer head belongs to forging parts, impact resistance, toughness, good wear resistance, not easy to break. Through the special quenching heat treatment method, to ensure that the hammer work to please the high hardness, high wear-resisting performance. The mechanical properties of forgings are generally superior to those of castings. Henan Shuangzhi Processing crushing shaft group hammer, drawing number: 27PW0201-1 hammer, 9P07-6, 25P03-07, 34P12-15, 6CE05-3, TPL601-15, 25PG01-2, TPL501-15, TPL301-07 and other various main machine matching drawing number of hammer. Welcome you to consult procurement.
-sterling silver ring with blue bugget stones. -stone info: AAA:5mm-1pcs 1.1mm-8pcs Blue spinel:1*2*2.5mm-16pcs -rhodium plated -MOQ: 100PC+
The crushing shaft group is the main component of the crushing material, which is composed of the cutter body, cutter tooth base, crushing shaft, fastening assembly, fixing seat and other structures. After the test, it is sent to the user. What details should be paid attention to when it is put into installation operation? 1. Place the crushing box horizontally, remove the top cover, remove debris and apply anti-rust oil on the processing surface. Place the broken shaft set smoothly at the gap. 2. Use grease to empty the inner period of the rubber hose for filling bearing seat. Connect the manual dry oil station with the rubber hose for bearing seat until the labyrinth ring at both sides of the bearing seat in the crushing box spills oil. 3. Install pressure plates and dust cover plates on both sides. 4. The rise and fall of the crushing shaft set is controlled by two hydraulic jacks. Before adjusting the crushing shaft set, the tensioning screw should be adjusted to make the belt in a relaxed state. Pull out the lock pin and loosen the wedge with the jack top to adjust the crushing shaft set to the required height. Then wedge the wedge and adjust the tensioning screw so that the belt is in tensioning state, then insert the locking pin. During the operation of the broken shaft group, a large amount of coal dust is likely to be generated, which seriously affects the work safety and personal safety. Therefore, dust removal and dust removal should be carried out timely. Henan Shuanzhi produces crushing shaft set and its accessories, welcome to inquire.
The hammer head of the crusher is an essential accessory for the coal mine crusher. At present, the common crusher hammer head on the market is generally divided into two kinds, forging hammer head and casting hammer head. The hammer head of forging crusher is mainly used to heat the blank and apply pressure on the blank by forging machine to produce plastic deformation of the blank, so as to obtain the hammer head of the crusher with the given shape, size and mechanical properties. The casting loose defect caused by casting hammers can be greatly changed by forging and the structure of hammers can be optimized. Therefore, the forging hammer head performance is superior to the casting hammer head, relatively also more wear-resisting. In order to guarantee the wear resistance of forging hammer head, it is necessary to choose the material with better wear resistance. At present, the common materials in the market include high manganese steel, high chromium cast iron, low carbon alloy steel, etc., which can be selected according to the use conditions of different mining areas. Coal machine parts manufacturer Henan Shuanzhi production of various types of forging hammer head, crushing shaft group. More coal accessories small knowledge, welcome you to continue to pay attention to Henan Shuangzhi.
The hammer head used in coal mine has abrasion resistance and impact resistance. The hammer head is an important working part of the crusher. Its production capacity is determined by its shape and material quality. Generally speaking, the hardness of the material is higher, the hardness of the hammer head material is higher, the hardness of the hammer head is higher, the greater the wear resistance of the hammer head is greater, the impact load of the hammer head is greater, the higher the requirement for its toughness. The wear of hammers is related to many factors, such as material, underground environment, weight, product quality, etc. The maintenance and maintenance of each part of the hammer head is very important, as the core parts of the hammer head, not only the market demand is large, the crusher hammer head wear resistance also to meet the standard. Henan Shuangzhi mainly produces crusher accessories such as crushing shaft group, hammer head, cutter tooth base, fixed base, fastening assembly, belt pulley and so on.
23P03 crushing shaft is the main part of the crushing material of PLM1000 wheel crusher. The whole machine has great crushing capacity, high strength and rigidity, and is safe and reliable. The bearing adopts manual dry oil station for centralized lubrication to extend the refueling cycle. 23P03 crushing shaft group is mainly formed by the short technology of the knife body on the crushing shaft and the crushed material to impact and crack the coal, and then the speed difference between the knife tooth base, scraper chain and crusher is made to further roll and pull the crushed coal, so as to achieve the purpose of crushing the coal. After installation, it shall be checked that the rotating part of 23P03 broken shaft set shall not contact with any other parts in the box body; The distance between any particular point of the rotating part of the crushing shaft set and the side wall of the crushing box shall be equal on the circumference of the crushing box; The fastening bolts between the cutter body and the cutter tooth base shall not be loosened, and the cutter body shall not be cracked. If the crushing shaft is rotated manually, it shall be stable without abnormal sound; The belt grooves on the belt pulley have no bump marks; Prepare for complete machine test in conjunction with its components. To determine the manufacturer of 23P03 broken shaft, it is necessary to consider the material process experience. Henan Shuanzhi do quality manufacturers, now should the market demand spot supply, welcome to the factory consulting investigation.
The hammer head of the crusher is an essential accessory for the coal mine crusher. At present, the common crusher hammer head on the market is generally divided into two kinds, forging hammer head and casting hammer head. The hammer head of forging crusher is mainly used to heat the blank and apply pressure on the blank by forging machine to produce plastic deformation of the blank, so as to obtain the hammer head of the crusher with the given shape, size and mechanical properties. The casting loose defect caused by casting hammers can be greatly changed by forging and the structure of hammers can be optimized. Therefore, the forging hammer head performance is superior to the casting hammer head, relatively also more wear-resisting. In order to guarantee the wear resistance of forging hammer head, it is necessary to choose the material with better wear resistance. At present, the common materials in the market include high manganese steel, high chromium cast iron, low carbon alloy steel, etc., which can be selected according to the use conditions of different mining areas. Coal machine parts manufacturer Henan Shuanzhi production of various types of forging hammer head, crushing shaft group. More coal accessories small knowledge, welcome you to continue to pay attention to Henan Shuanzhi.
34P12-15 cutter teeth matching 34P12 crushing shaft set, the main machine is PLM4500 wheel crusher. Special fastening bolts and nuts are used in the golden cauldron for matching the cutter tooth base after forging, and the bolts and nuts are stuck with anti-loose gaskets. PLM4500 wheel crusher is installed at the fixed position in the landing section of SZZ1350/525 channel bridge transfer machine. When transporting coal, the crushing shaft of the crusher drives the crushing knife teeth to rotate, impact and cut large pieces of coal, and crush them into the required lumpness. The 34P12 crushing shaft set is equipped with 34P12-01 shaft, 34P1201 bearing seat, 34P12-04, 34P12-05, 34P12-15 cutter teeth and other accessories. If you need broken shaft group, please contact Henan Shuanzhi, welcome to visit the factory.
On the working face of fully mechanized coal mining, the trough crusher is used with the transfer machine, and the high speed rotating hammer head is used to impact and crush the large raw coal, so as to crush it into the required grain size. Hammer shaft component hammer head is the key part of the crusher, which needs to have high hardness and stiffness. The impact on the hammer head of the hammer shaft assembly is relatively large, so the head of the hammer head should have good wear resistance and the handle should have sufficient toughness. The hammer head of the hammer shaft assembly is usually forged or cast by alloy steel, high manganese steel, cast steel and high chromium cast iron bimetallic composite. The surface of hammer head is quenched by medium frequency quenching induction equipment. To a large extent, the damage of the crusher is due to the failure of the hammer head of the hammer shaft assembly, the poor wear resistance of the hammer head and the loosening of the hammer head will bring losses to the coal mine production. Therefore, when using the hammer head of the hammer shaft assembly, some anti-loose measures should be taken. Coal mining enterprises should also choose hammer head with good quality. Henan Shuangzhi produces various types of hammer head and hammer shaft components, complete product technology, strict quality inspection, durable and easy to use products, if you have the mining crusher accessories procurement needs, you are welcome to consult.
The cutter head, also known as hammer head, is the main vulnerable part of the crushing shaft, and it is also the part that bears great impact force when crushing coal. There are castings and forgings on the market, but the castings bearing strength is small and the service life is short. Blade was covered a layer of wear-resisting layer forging and become, blade and blade both use a special fastening bolt and nut set, blade bolts and nuts with locking washers, when wear to a certain situation or cracks have appeared, should change in time, otherwise will make the blade are installed on the part of the blade is damaged, and can no longer be tighten blade on the blade holder. The broken shaft without cutting teeth will lose its balance, and the strong vibration will shorten the service life of the broken shaft sharply. Shuangzhi coal machine for many years focused on the scraper conveyor, transfer machine accessories, crusher accessories system repair, products sold to the major mining areas, more information please click on the official website of Shuangzhi coal machine or call to inquire the factory investigation
The crushing machine series of mine scraper conveyer is mainly used in combination with the transferring machine and complete the conveying task of underground comprehensive mechanized coal mining with belt conveyer, scraper conveyer, shearer and hydraulic support. The models of mine crusher are PCM, PEM, PLM, etc. They are respectively represented as hammer crusher, jaw crusher, wheel crusher, etc. According to different working face and production capacity of mine, different crushing capacity of crusher is required. For example, PLM3000 wheel crusher has crushing capacity of 3000T /h. PLM4000 wheel crusher with crushing capacity up to 4000T /h. The crushing shaft group is the main component of the crushing coal and gangue. Using the broken shaft set higher rotational inertia stored at rated speed kinetic energy by installing group on the shaft of the broken blade and the broken material short contact time and impact break coal formation, again by cutter tooth and scraper chain, crusher, the speed difference between further to crush was broken coal, so as to achieve the goal of broken coal. Shuangzhi Coal machine focuses on the production and manufacturing of spare parts of scraper machine, transferring machine spare parts and crusher spare parts for mine. It is located in Zhengzhou with developed logistics. At present, it cooperates with major mining areas all over the country.
S33 series sand crusher is the fourth generation crusher developed by our company. The device sets crushing, Screening, primary regeneration as a whole. Compared with the built-in crusher, this machine has the advantages of reliable use, simple structure and convenient maintenance.
Common hammer head hammer head materials are: high manganese steel, low carbon alloy steel, high chromium cast iron. High manganese steel has better toughness, better technology and lower cost. But the processing hardening of high manganese steel requires higher processing technology. If the impact force is not enough and the contact stress is too small, the surface cannot be hardened. Low carbon alloy steel has high hardness and toughness. At the same working strength, the service time is twice that of high manganese steel. High chromium cast iron has poor toughness and is prone to fracture. High chromium cast iron is usually used as hammer handle on the head of high manganese steel and low carbon alloy steel to make it have hardness and toughness. The quality of manufacturing process is to determine the service life of the hammer head. If there are shrinkage holes or cracks on the surface or inside of the hammer head, it will reduce the performance of the hammer head and even cause fracture in the operation process, affecting the working efficiency. In the manufacturing process of hammer head, forging and heat treatment process should be strictly controlled, and strict quality inspection process should be established. Hammer heads of different structure and geometry have different performance after heat treatment and forging. Generally speaking, the thicker the hammer head, the larger the size, the less easy to penetrate. However, it is limited to change this situation through reasonable heat treatment and forging, so it is still necessary to optimize the structure and shape of the hammer without affecting the use effect. In general, the rotor speed of the broken shaft group is high, the greater the impact force on the hammer head, it can be better impact hardening. But also can cause the hammer head service life to reduce, the crusher power consumption is too big. Therefore, a reasonable speed should be set. If the clearance between crushing shaft rotor, grate, crushing plate and feeding roller is too small, it will lead to the blockage of coal. If the clearance is too small, the crushing effect and efficiency are too low. Hammer head crusher in the use of time, often adjust the clearance between the parts, so that it in the appropriate range. The shape and quality of hammer head directly affect the yield and service life of the crusher. When buying a crusher hammer head, pay more attention to the above mentioned factors, choose suitable for toughness hammer head. Henan Shuangzhi Machinery Equipment Co., LTD. Produces hammer head of crusher, crushing shaft group, scraper conveyor accessories. Welcome customers to purchase.
The crushing shaft is composed of crushing shaft, cutter tooth base, cutter tooth, flat key, bearing, seal and fastening bolt. The strong rival of coal "big block" is broken shaft group, today we are going to introduce this "strong rival"! Trough crusher is used with the transfer machine, using the high speed rotating hammer head to impact and squeeze large raw coal, so as to achieve the required particle size. The crushing shaft assembly is the key component of the crusher, which requires high precision and high stiffness. The middle part of the spindle is equipped with hammer head, which is directly involved in impact crushing. Its performance is the key. Due to the large impact load of the hammer head, high rotation speed, the use of mining is extremely bad, so the performance of the hammer head largely determines the reliability of the crusher. Main parts function, structure characteristic and installation and maintenance of broken shaft 1. The rotating part of the crushing shaft assembly shall not contact with any other parts in the box body. 2. The distance between any particular point of the rotation part of the crushing shaft set and the side wall of the crushing box is equal on the circumference of the crushing box. 3. The fastening bolts between the cutter body and the cutter tooth base shall not be loosened, and the cutter body shall not be cracked. 4. Manual rotation of the crushing shaft should be smooth and sound. 5. There is no bump mark in the belt groove on the pulley. 6. Prepare for complete machine test in coordination with other parts.
Glow in the dark stones (glow stone, glow in the dark rocks/pebbles) are resin or glass stones that create a unique luminous visual effect in the dark environment and require no electrical powder. Glow Technologys glow stones have various day and glow color choices and last a lifetime indoors and out.
65-1590 tons per hour -YC series jaw crusher A new TYPE YC jaw crusher is suitable for breaking all kinds of metal ore for the first time. The simplest heavy crushing equipment made in China, low price, simple structure, reliable durability, less maintenance cost. PRODUCT FEATURES: 1 .Extremely reliable design 2.Outstanding performance 3.Safe to operate and maintain 4.Easy to install
YJ series jaw crusher is an efficient and reliable jaw crusher developed with advanced V-cavity design and large bearing design concept, which can crush the hardest minerals and rocks in the most severe environment. YJ series jaw crusher is characterized by firm mechanism, high productivity and efficiency, less wear and good lubrication and sealing effect Characteristic and advantage: 1 .Optimized design of crushing chamber improved productivity and efficiency in order to prevent blocking of the material and make the better use of wearable liner. 2.Welding structure design of the fiame is stable and assure the reliability of the crushing operation at the sever environment. 3.Hydraulie adjusting design is easy and convenient operation. 4.Heavy duty and high serength eccentric shaft design offer bigger crushing force and improve the partical size and productivity. 5.The rigidity design of the swing jaw and toggle plate ensure its service life and stability.
PEF double pendulum jaw crusher - The jaw crusher is the main equipment for coarse crushing (one stage crushing). With this equipment, large material (rock, ore) is roughened and broken into smaller size, into small rocks or gravel. Through the screening of the vibrating screen and the dressing of the concentrator, the materials are sorted into products of various sizes and types. The small yield of the jaw is broken, and most of the options are multi-pendulum jaw crusher. For large yield jaw crusher, choose large simple pendulum jaw crusher. The main features are: Simple structure, reliable performance, easy operation, easy maintenance, safe use, strong applicability, cheap price.
The jaw crusher is the main equipment for coarse crushing (a section of crushing). The main features are: Simple structure, reliable performance, easy operation, easy maintenance, safe use, strong applicability, cheap price. The jaw crusher is divided into two forms: compound pendulum and simple pendulum. The main parts of a broken jaw are: Frame, movable jaw, active eccentric shaft, supporting shaft (simply swinging), connecting rod, adjusting jack, Model description: Lining plate, fixed tooth plate, movable jaw plate, transmission bearing, movable jaw bearing, belt wheel, flywheel. Small jaw fracture is compound pendulum. Large jaw broken simple pendulum more, and the frame is divided into upper and lower compartments. Model description: P E F (J) XX to XX P: crusher E: jaw crusher F(J): Compound pendulum (simple pendulum) XX: Give the opening width mm/100 XX: Length of mine outlet mm/100
