Crushing Shaft Assembly Of Crusher For Sale

The crushing shaft group is the main component of the crushing material, which is composed of the cutter body, cutter tooth base, crushing shaft, fastening assembly, fixing seat and other structures. After the test, it is sent to the user. What details should be paid attention to when it is put into installation operation?

1. Place the crushing box horizontally, remove the top cover, remove debris and apply anti-rust oil on the processing surface. Place the broken shaft set smoothly at the gap.

2. Use grease to empty the inner period of the rubber hose for filling bearing seat. Connect the manual dry oil station with the rubber hose for bearing seat until the labyrinth ring at both sides of the bearing seat in the crushing box spills oil.

3. Install pressure plates and dust cover plates on both sides.

4. The rise and fall of the crushing shaft set is controlled by two hydraulic jacks. Before adjusting the crushing shaft set, the tensioning screw should be adjusted to make the belt in a relaxed state. Pull out the lock pin and loosen the wedge with the jack top to adjust the crushing shaft set to the required height. Then wedge the wedge and adjust the tensioning screw so that the belt is in tensioning state, then insert the locking pin.

During the operation of the broken shaft group, a large amount of coal dust is likely to be generated, which seriously affects the work safety and personal safety. Therefore, dust removal and dust removal should be carried out timely. Henan Shuanzhi produces crushing shaft set and its accessories, welcome to inquire.

23P03 crushing shaft is the main part of the crushing material of PLM1000 wheel crusher. The whole machine has great crushing capacity, high strength and rigidity, and is safe and reliable. The bearing adopts manual dry oil station for centralized lubrication to extend the refueling cycle.

23P03 crushing shaft group is mainly formed by the short technology of the knife body on the crushing shaft and the crushed material to impact and crack the coal, and then the speed difference between the knife tooth base, scraper chain and crusher is made to further roll and pull the crushed coal, so as to achieve the purpose of crushing the coal.

After installation, it shall be checked that the rotating part of 23P03 broken shaft set shall not contact with any other parts in the box body; The distance between any particular point of the rotating part of the crushing shaft set and the side wall of the crushing box shall be equal on the circumference of the crushing box; The fastening bolts between the cutter body and the cutter tooth base shall not be loosened, and the cutter body shall not be cracked. If the crushing shaft is rotated manually, it shall be stable without abnormal sound; The belt grooves on the belt pulley have no bump marks; Prepare for complete machine test in conjunction with its components.

To determine the manufacturer of 23P03 broken shaft, it is necessary to consider the material process experience. Henan Shuanzhi do quality manufacturers, now should the market demand spot supply, welcome to the factory consulting investigation.

The crushing shaft is composed of crushing shaft, cutter tooth base, cutter tooth, flat key, bearing, seal and fastening bolt. The strong rival of coal "big block" is broken shaft group, today we are going to introduce this "strong rival"!

Trough crusher is used with the transfer machine, using the high speed rotating hammer head to impact and squeeze large raw coal, so as to achieve the required particle size. The crushing shaft assembly is the key component of the crusher, which requires high precision and high stiffness. The middle part of the spindle is equipped with hammer head, which is directly involved in impact crushing. Its performance is the key. Due to the large impact load of the hammer head, high rotation speed, the use of mining is extremely bad, so the performance of the hammer head largely determines the reliability of the crusher.

Main parts function, structure characteristic and installation and maintenance of broken shaft

1. The rotating part of the crushing shaft assembly shall not contact with any other parts in the box body.

2. The distance between any particular point of the rotation part of the crushing shaft set and the side wall of the crushing box is equal on the circumference of the crushing box.

3. The fastening bolts between the cutter body and the cutter tooth base shall not be loosened, and the cutter body shall not be cracked.

4. Manual rotation of the crushing shaft should be smooth and sound.

5. There is no bump mark in the belt groove on the pulley.

6. Prepare for complete machine test in coordination with other parts.

The Zenith VSI crusher is widely used for crushing of hard and crispy materials, such as rocks, grinding materials, refractory materials, cement clinkers, quartzite, iron ores and concrete aggregates.The stone crusher is especially suitable for the sand and sandstone making for construction and road paving. The crusher can cycle many times with the close circuit and the sieve device will control the granularity of finished products.ThisVsi crusher is applied widely for the powder process of mineral product including mental and non-metal ore, fireproof material, bauxite, diamond dust, glass raw materials, architectural materials, artificial sand and all kinds of metal ore materials, especially which has more advantages than any other machines in processing the more and most hard materials
VSI Crusher Features:
1. Excellent performance and high final fineness 2. Safe and user-friendly 3. Smooth and quiet operation 4. Minimum maintenance 5. Heavy duty design 6. Long service life 7. Standard replacement parts 8. Cost effective 9. Cubically shaped product 10. High productivity.

Introduction:
Cone crusher is suitable for crushing all kinds of ores and rocks above medium hardness. It has the features of reliable structure, high productivity, easy adjustment and economical operation etc. It is widely used in metallurgy, architecture, rock making, chemistry and silicate industry for crushing various mid-hard and hard ores and rocks. The spring system acts as an overload protection system that allows iron to pass through the crushing chamber without damaging the crusher. It uses consistent grease or water for sealing, which separates crushed particles and lubricating oil, and ensures reliable work. The types of crushing chamber depend upon the usage of the final products. The standard type is applied to medium crushing; the medium type is fit for medium and fine crushing and the short head type is fit for fine crushing.
Main Features:We supply a wide range of Cone Crushers, for various secondary and tertiary crushing applications, therefore to insure the best and most feasible Cone Crusher type, fit for different plant configurations, designed for the most efficient and economical production and rock down sizing application. Our Cone Crushers are supplied in four general categories, designed for various types of secondary or tertiary applications, both for closed circuit and open circuit configuration: 1.Coarse type application. 2. Fine or medium type crushing. 3. Short head design.4. Super short head for fine crushing application. 5. Continuous Lubrication:
This type of crushers are supplied with high capacity external mounted lubrication unit, composed of oil-tank, oil filtering system, high oil temperature shut-down, low oil flow shut-downs and oil flow gauge, which is designed to supply continuous and stable oil, by forced lubrication to the Cone Crusher, for smooth rotation and operation. 
Cone Crushers are configured with many safety features. The lubricating unit is interlocked with the main motor, in order to provide additional safety, which includes oil filtration and automatic shut-down in the event of high oil temperature, as well as low oil flow. Crushers are configured with Spring-Loaded release system, which allows any inscrutable material to pass through the crusher, without causing damage to the crusher. The locking system (manual or hydraulic), will easily secure the crushing clearance. All models are configured with proven spring-type mechanism, in order to recover Tramp-Iron and provide protection to the unit.
Applications :Cone crusher is a kind of crushing machine commonly used in mining, metallurgical industry, construction, road construction and chemical industry. Our cone crusher can be used to crush hard and medium hard minerals, rocks, iron ores, limestone, copper ores, quartz, granite, sandstones, etc.

Stone hammer crusher application: this series of stone hammer is applicable crushing of brittle minerals, such as coal, salt, plaster, alum, brick, tile and limestone with compression strength no more than 100mpa and humidity no more than 15%.
Pc hammer crusher introduction:this series of machine broke materials through the high-speed rotating hammer body and collision the material surface, it has a simple structure, large crushing ratio, high production efficiency and other characteristics, it can be used for dry and wet two forms crushing, it applies to mining, cement, coal, metallurgy, building materials, roads, fire and other departments chronology medium hardness and brittle materials. The device can change material particle size and adjust gap of article grate in accordance with user requirements, so it can meet different users
Structural characteristics: stone hammer crusher has compact frame, reasonable layout, easy installation, good maintainability, simple operation. Particularly, it excellently adapts the layout of cement production process, save the space of process layout. With special structural characteristics, that is having big materials ratio etc.
Stone hammer crusher is divided into ordinary hammer crusher and ring hammer crusher respectively. Ring hammer crusher generally used in coal, coke and other industries. Ordinary hammer general english prefix is expressed by pc, used pch english prefix that usually is ring hammer crusher.