MTB-403 Instant Glue Large is of MTB Istant Glue sery ,here i give the detials as below. 1. Production Character A. A type of low ordour and low bloom product B. Has the character of good wetness resistance C. Do not need complicated ventilating system 2. Production Application This production is mainly for the inexact coopreated parts adhesive. For cyanoacrylate glue, our packing is as one piece with 20g, 10pcs in one box , 50 boxes in one carton .And we can do the packing as your designs and requirements.
The series of LED silicone packaging materials, mainly used in light-emitting diodes ( LED ) package, having a high refractive index and high light transmittance, can increase the LED luminous flux, low viscosity, easy for deaeration, pouring and molding, make LED has better durability and reliability. This series product is a two-component silicone fluid sealant with high refractive index. Mainly used for electronic components of the seal, enhanced electronic device integrity, improve to shocks, shock resistance, improve the internal components, circuit insulation, conducive to device miniaturization, lightweight, avoid element, circuit is directly exposed to the environment, improve the device's waterproof, moisture-proof performance. Features: high light transmittance, high refractive index, fast curing speed, good fluidity, good heat resistance, weather resistance; Typical application: high-power LED light emitting diode package ( lens filler ), large power LED module top molding package, TOP chip, SMD chip, LED package, LED fluorescent powder glue, potting products such as solar panels. 0.5kg/bottle.
Super glue is a single-component cyanoacrylate monomer in the liquid state, capable of extremely rapid polymerization between adherent surfaces, result-ing in extremely strong and structural bonds at room temperature. This instant adhesive will, with only normal surface preparation, bond all materi-als commonly used in the engineering industry, except polyethylene. Polypropylene, teflon, and very porous surfaces, which require special treatment. Application suits for metal, rubber, ceramics, plastic, wood. Appearance colourless transparent liquid Specification : 3 gram/tube,2 tubes /blister card Packing : 288 card/carton Measurement(cm) : 38*36*42 1 container 20 feet 490 cartons 1 container 40 feet 1010 cartons.
Super glue is a single-component cyanoacrylate monomer in the liquid state, capable of extremely rapid polymerization between adherent surfaces, result-ing in extremely strong and structural bonds at room temperature. This instant adhesive will, with only normal surface preparation, bond all materials commonly used in the engineering industry, except polyethylene. Polypropylene, teflon, and very porous surfaces, which require special treatment. To open tube: 1. Unscrew entire nozzle & cap unit. 2. Reverse cap and place pointed end on top of tube. Point tube away from face, Press to puncture. Do not squeeze tube while puncturing. After puncture is made, replace nozzle & cap. 3. Unscrew outer cap only and apply sparingly. Clean tip after each use. Application: Be sure both surfaces are clean and dry. Apply with extreme care. Never spread with fingers. Apply one drop for each 3 cm area. Apply to only one of the surface, Quickly place two surfaces together with slight finger pressure. Bond is completed in seconds, or depending on material in about one minute, leave for 24 hours for strongest bond. Clean away all excess adhesive from container with ties-sue paper. Keep out of reach of children, in cool dry place. Warning: Keep out of reach of children: Adhesive will stick to skin very quickly, when using, be sure it dose not come into contact with fingers, do not try to pull it off. Soak fingers in warm water and work off Nail polish remover may also be used. If adhesive get in eye, wash eye with quantities of plain water, do not try to remove by rubbing or applying solvents, in case of pain or discomfort, consult a doctor. Bond for home uses: For mending dishes and household articles, tables, chairs, bureaus and other articles of furniture, fishing tackle and other sports equipment, or for use on metal, leather or paper. Application suits for metal, rubber, ceramics, plastic, wood. Appearance colorless transparent liquid Specification 3 gram/tube,12 tubes/blister card. Packing 72 card/carton Measurement(cm) 57*28*38 1 container 20 feet 465 cartons 1 container 40 feet 960 cartons G.W/N.W(KG) 11 KG/10 KG Shelf Life 12 months.
8805 is waterbase PU adhesive, for bonding fabrics, rubber, PU, PVC, TPR, EVA, real leather, etc materials. Targeted at the imported high price waterbase adhesive of the market, developing and synthetizing independently waterbase PU adhesive, suitable for both assembly line and handwork.. High solid content, high quality, high viscosity, excellent permeability and anti-skipping performance, good oil-resistance and bonding feeling, strong initial viscous. Environmental protection, non-yellow, non-odor, excellent combine performance, wide application, etc. 20L/can, N.W.: 14KG, G.W.: 15KG.
148K is a water base spray adhesive, it is designed for swivel chair, mattress, high grade hug pillow, fabric, thick leather sofa, folding screen. Excellent bonding performance for those materials, like: foam to foam, foam to PU leather, foam to PVC leather, foam to fabric, foam to wood, fabric to fabric, fabric to wood, pu/pvc leather to wood, etc. Its character is odorless, environmental protection, good weather resistance, good temperature resistance and oil-resistance, non-pulverization. 20L/can, N.M.: 14KG, G.W.: 15KG.
Water base adhesive for vacuum thermoforming is one component water base polyurethane adhesive. Best quality PUD is used and it is totally environmental protection, innocuity, safety and non-odor, etc. It has excellent performance on heat resistant, fast drying, strong initial viscous, endurance bonding strength, and atomization. Suitable for materials such as pvc with MDF, chipboard or wood board etc. in the vacuum thermoforming area. It is widely applied to waterbase vacuum thermoforming products, like vacuum thermoforming door, kitchen cabinet panel, sound box panel, computer desk etc. 20L/can, N.W.: 14KG, G.W.: 15KG.
Application: 1. Lamination of various plastic materials(such as PET, PE, PO, OPP, BOP, PP and CPP etc.) and carpet. 2. Lamination of some special material(such as aluminum foil, aluminized film etc. ) 3. Lamination of various paper to paper/paper to plastic/paper to aluminum foil(aluminized film) etc. 4. It is widely applies in the soft packing factory, for no harm to any animals, it is very popular in the food package industries. And also the food packing factory, color printing factory, printing factory, laminated factory and lampshade factory etc. 20-125KG/Drum(According to customer¡¯s requirement).
Waterbase composite superglue888A/H is made from waterbase copolymers, designed for compositing shoes fabrics and EVA compositing. Improved strong-odor, high volatility, and potential danger, etc. of the solvent coomposite superglue market, we independently develop enviromental friendly waterbase superglue. Absolute environmental protection, innocuity, non-odor, no fire-hidden-danger, excellent water-resistance and heat-resistance, fast crystallized speed, and stronger later force even to break the EVA material, easy operation, huge adhesion with direct rolling, especially for composting of shoes materials, and stability of high-temperature, etc. 20-200L drum.
Features: 1, This product is a new type strong adhesive, applied to indoor and outdoor wall paste of large-scale ceramic tile, grassing stone, natural stone material 2, The indoor ceramic tile adhesive of light steel frame system board, like gypsum board and Eight board 3, Can be used on the low water absorption surface, like paste new ceramic tile above the old ones, and can be used on the firm painting surface 4, Excellent flexibility, can bear the bonding layer stretch that caused by temperature 5, Good anti-infiltration function 6, No need to wet the brick wall, effectively improve the efficiency. Surface Treatment: 1, The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. 2, For the new wall, when finding the leveling layer of cement mortar, plaster, should improve the leveling layer of mortar label the cohesive force of the wall, or mix MB-03 slurry additive. Specific reference, please look at the MB-03 introduction. Operation process: 1, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2 2, Push the ceramic tile or heavy type ceramic tile above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material 4, Can be used for the old ceramic tile re-tread. Cautions: 1, Never mix the dry slurry with water and use again 2, For the light wall board install large-scale decorative panels, like gypsum board and Eight board, confirm the wall firmness before operation 3, For the painting surface, make sure the initial bond strength and no flake 4, Operating under 5¡æ~40¡æ situation 5, Clean the surface by little wet sponge or cloth before it dry 6, Leave 1.5mm joint space between two tiles, suggesting MB-MC color anti-moldy gap filler. Technical Reference: Coverage area(amount) Technical reference using 3*3mm tooth scraper about 1.7kg/m2 1, adjust time: about 15min (adjust time: the effective time for the dislocation to adjust) using 6*6mm tooth scraper about 3.0kg/m2 2, cool time: about 10min (cool time: the longest cool time that the adhesive can last ) using 10*10mm tooth scraper about 4.5kg/m2 3, dry time: 24h (according to the weather) 4, water resistance: excellent; non-toxic, prevent fire the smoother the surface, the less amount 5, when dry, anti-weak acid, anti-strong alkali and oil resistance 6, cut degree: £¾1.2MPa (14days later). Store Method: Store in cool and dry place, unopened product can be saved for one year. 25kg/bag
Features: 1, This product is a new type strong stone adhesive, applied to all kinds of low water absorption stone materials like large-scale artificial stones, culture stones, and natural stones 2, No need to wet the brick wall, effectively improve the efficiency 3, Strong bond ability, material-reducing, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the quantity of the wall 4, Good anti-acid and anti-alkali and anti-infiltration and anti-aging function 5, Small shrinking rate, no cracking, can be used in cold and humid environment. Application: 1, The adhesive for cement plaster, brick, smooth cement wall paste stone 2, The adhesive for low water absorption surface and light steel frame system board, like gypsum board and Eight board. Surface Treatment: The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. Operation Process: 1, The ratio: MB tough stone adhesive: water: 3.3: 1 (25kg powder, about 7.5kg water) mixed and stirred into paste, using an electric mixer to make particle paste, put it aside for a few minutes and then a little stirring to gain the better effect 2, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2, then push the stone above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Normal Amount: Coverage areas differ according to the circumstance: 1, using 3*3mm tooth scraper about 1.8kg/m2 2, using 6*6mm tooth scraper about 3kg/m2 3, using 10*10mm tooth scraper about 4.8kg/m2 Note: bricks for wall using 3*3mm tooth scraper or 6*6mm tooth scraper, bricks for floor using 6*6mm tooth scraper or 10*10mm tooth scraper. Cautions: 1, Make sure the smooth and vertical rate of the surface before operation 2, Never mix the dry slurry with water and use again 3, For the painting surface, make sure the initial bond strength and no flake 4, Finishing after 24h can be walked in or fill the crack. Store Method:Store in cool and dry place, unopened product can be saved for one year. 25kg/bag
Features: 1. Mixed with cement mortar, improving the bonding strength and flexibility 2. Can be used as booster for the interface treatment agent and tile adhesive 3. Improve the anti-infiltration and waterproof function of cement mortar, and make it suitable for the wet area like swimming pool 4. Anti-aging, non-toxic, safety. Surface Treatment: The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. Mixed Ratio: 1. For strengthen the bond performance: 50kg cement mortar with 3-5kg additive and appropriate water 2. For outdoor heavy-type ceramic tile adhesive: 5kg mb-01 powder + 1.1kg mb-03 + appropriate water; for indoor heavy-type ceramic tile adhesive: 5kg mb-01 powder + 0.6kg mb-03 + appropriate water; for smooth surface small ceramic tile adhesive: 5kg mb-01 powder + 0.8kg mb0-03 with appropriate water 3. For the interface treatment: 1.0kg mb-01 powder + 0.1kg mb0-03 with appropriate water 4. For the cement mortar leveling: about 2.5kg mb-03 mixed with 50kg cement. Operation Process: 1. The same operation process with mb-01 adhesive when paste various type of tiles and stone materials 2.Cement mortar leveling: according to the above ratio, mixed the mb-03 with cement mortar, then make inserting 3. Interface treatment: for the high water absorption surface, wet the surface at first, then brush the mixed slurry on the surface, control the thickness under 1.5mm, after it dries, doing the paste; for the low water absorption, no wet work, do with the above 4.for the old ceramic tile: a.mixing MB-01 with MB-03 in the rate of 1.1-1.2: 1 for the interface treatment b. after it dries, according to the process using MB-01 to operate directly c. or use MB-01 directly for the old wall retreating. Cautions: 1. The mortar that attached to the surface should be clean before it dry 2. Operating under 5¡æ~40¡æ situation 3. Finished after 24h, can be walked or fill crack 4. For the old surface retreating, clean the loosen or flake ceramic tile at first. Technical Reference: Coverage area(amount). Technical reference 1, for ceramic tile and stone: A, mixed cement about 0.7kg/m2; B, mixed MB-01 0.4-0.6kg/m2; adjust time(20¡æ): about 10min cool time(20¡æ): about 10min 2, for interface treatment: about 0.15kg/m2 when dry, anti-weak acid and oil resistance 3, for cement mortar leveling: about 0.1kg/m2 Improve the cement bonding strength: 80%(14days). Store Method: Store in cool and dry place, unopened product can be saved for one year. 25kg/bag
Features: 1, This product is a new type strong stone adhesive, applied to all kinds of low water absorption stone materials like large-scale artificial stones, culture stones, and natural stones 2, No need to wet the brick wall, effectively improve the efficiency 3, Strong bond ability, material-reducing, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the quantity of the wall 4, Good anti-acid and anti-alkali and anti-infiltration and anti-aging function 5, Small shrinking rate, no cracking, can be used in cold and humid environment. Application: 1, The adhesive for cement plaster, brick, smooth cement wall paste stone 2, The adhesive for low water absorption surface and light steel frame system board, like gypsum board and Eight board. Surface Treatment: The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. Operation Process: 1, The ratio: MB tough stone adhesive: water: 3.3: 1 (25kg powder, about 7.5kg water) mixed and stirred into paste, using an electric mixer to make particle paste, put it aside for a few minutes and then a little stirring to gain the better effect 2, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2, then push the stone above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Normal Amount: Coverage areas differ according to the circumstance: 1, using 3*3mm tooth scraper about 1.8kg/m2 2, using 6*6mm tooth scraper about 3kg/m2 3, using 10*10mm tooth scraper about 4.8kg/m2 Note: the amount is related to the smooth, vertical rate, and thickness of the stone material Cautions: 1, make sure the smooth and vertical rate of the surface before operation 2, never mix the dry slurry with water and use again 3, for the painting surface, make sure the initial bond strength and no flake 4, Finishing after 24h can be walked in or fill the crack. Store Method: Store in cool and dry place, unopened product can be saved for one year. 25kg/bag
Features: 1. This product is a new type strong adhesive, applied to indoor and outdoor wall paste of large-scale ceramic tile, grassing stone, and natural stone material 2. The indoor ceramic tile adhesive of light steel frame system board, like gypsum board and Eight board 3. Can be used on the low water absorption surface, like paste new ceramic tile above the old ones, and can be used on the firm painting surface 4. Excellent flexibility, can bear the bonding layer stretch that caused by temperature 5. Good anti-infiltration function 6. No need to wet the brick wall, effectively improve the efficiency. Surface Treatment: 1. The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. 2. For the new wall, when finding the leveling layer of cement mortar, plaster, should improve the leveling layer of mortar label the cohesive force of the wall, or mix MB-03 slurry additive. Specific reference, please look at the MB-03 introduction. Operation Process: 1. Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2 2. Push the ceramic tile or heavy type ceramic tile above it 3. For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Cautions: 1. Never mix the dry slurry with water and use again 2. For the light wall board install large-scale decorative panels, like gypsum board and Eight board, confirm the wall firmness before operation 3.For the painting surface, make sure the initial bond strength and no flake 4.Operating under 5¡æ~40¡æ situation 5.Clean the surface by little wet sponge or cloth before it dry 6.Leave 1.5mm joint space between two tiles, suggesting MB-MC color anti-moldy gap filler. Technical Reference: Coverage area(amount). using 3*3mm tooth scraper about 1.7kg/m2. using 6*6mm tooth scraper about 3.0kg/m2. using 10*10mm tooth scraper about 4.5kg/m2. Technical reference: 1, Adjust time: about 15min (adjust time: the effective time for the dislocation to adjust) 2, Cool time: about 10min (cool time: the longest cool time that the adhesive can last ) 3, Dry time: 24h (according to the weather) 4, Water resistance: excellent; non-toxic, prevent firethe smoother the surface, the less amount 5, When dry, anti-weak acid, anti-strong alkali and oil resistance 6, Cut degree: £¾1.2MPa (14days later). Store Method:Store in cool and dry place, unopened product can be saved for one year. 25kg/bag.
It is often used for making matches, as glue/adhesive in works of printing, wooden furniture, publication, the abrasive paper of the gauze , feed and so on. It sometimes also used as glue additive. The viscosity is very important for use.
Features: 1) Industry bone gelatin: a) Often used for making photographic paper, fixture and Galvan plastics liquid, match and wooden furniture. The product is under the QB/T1995-94 national trade standard. b) Packing making with the container bag of cow hide, gift box c) Sometimes also used as glue additive. 2) Bone glue in pearl: a) Made of animal bones. b) Bone was grounded into powder, dissolved in water, evaporated and dried into a hard jelly c) Also can be used in mortise-and-tenon work as match industry d) To be used with book, stationery as glue additive. 3) The bloom and viscosity are very important for use. 4) Specified specifications will make our reply more accurate.
Type :stick Color : blond black Welcome to test our quality
Uses:it is fit to be used for the adhesion of materials like electric appliances, heat-shrinkable material, packing material, fabrics, leather, lumber, plastic, metal, ceramics, etc. Performance:it is transparent, light yellow viscous solid, non-toxic, no stimulation, soluble in most organic solvents, non-soluble in water. It has good mechanical strength, good fluidity, excellent tenacity and high adhesion strength. Packing:pe film lined pp woven bag, net wt 25kg.
Uses: it can be used in pipe surface as anti-corrosion coating, apply for epoxy primer, and the coated mortar. It is also widely used in epoxy glue, antirust paint and antisepsis coatings and so on. Performance: it has good curing properties, good adhesion, easy to peel off, with good bending properties and excellent resistance to impact resistance. It has wider range than epoxy resin and easy to operate. Plastic drum or plastic coated metal pail, net wt 180kg
Our cyanoacrylate adhesive super glue is a high viscosity adhesive featuring the characteristic function as long shelf life and strong toughness and low bloom. It is suitable for the repairing and the adhesive of exquisite goods, such as jade, leather, porcelain, wood, leather, toys and artwork.It absolutely conform to environment-protection standard.We have passed rohs, reach, eu, ce, and iso 14001:2004 international certificate.They have following character: Nontoxic, environment-protection. Fast dry High viscosity Low-bloom No strong smell Long lasting 3gram/tube, 1, 2, 3, 12 pcs/card
