Wood chips rotary dryer is used for drying materials with a certain humidity lightweight material, such as bean dregs, wood chips, cassava dregs, Marc, distiller's grains, and others. Our special design wood chips rotary dryer has a strong adaptability of materials and it can dry various materials. This type of wood chips rotary dryer operation is very simple and liable. Also our professional wood chips rotary dryer has played an important role in various drying industries,wood chips rotary dryer is used for drying materials with humidity or granularity in the industries of mineral dressing, building material, metallurgy, and chemical.wood chips rotary dryer can be used for drying many kinds of materials and with convenient and reliable operation; therefore, it has been widely used.
Supercapacitor test separator 1 Applicable range: suitable for diameter 4 22mm, aluminum shell length 8 ~ 40mm, test voltage from 0V ~ 5VDC. 2ã?? Test item: ESR (1kHz) fixed current pulse charging 60s charging voltage. Three. Test process: the farad capacitor is fed through the vibrating material tray, and then transferred to the test conveying chain through the flat feeding and the hand over feeding of the manipulator. First, the guide pin is shaped; then, the polarity is tested, and the stepping motor is automatically reversed. After the second foot trimming, the products whose voltage at the test capacitor end is greater than 20mV are put into the retest material box, and the equivalent series resistance ESR (frequency 1kHz, apply 1mA or 10mA current, check Measure the voltage at the end of the capacitor, record the ESR grading range (high ESR, low ESR) of the measured capacitance with the internal resistance test instrument, directly discharge the ESR defect, then detect the open circuit and short circuit, enter the open circuit and short circuit material box, set the constant current charging current I of the capacitor, and pulse the farad capacitor on the test chain for 60s 0.1s, Carry out the voltage test at the end of the capacitor; unqualified voltage products enter into the poor voltage material box; Classification of qualified products (1) High voltage & high ESR (2) High voltage & low ESR (3) Low voltage & high ESR (4) Low voltage & low ESR, unqualified gear is divided into two gears, (5) Open circuit (6) Short circuit, 6 gears in total, then enter the load discharge and short circuit discharge section, six kinds of which are put into the corresponding material box respectively. 4 Performance 1. Single phase AC220V power supply of vibrating plate feeding system, 50 / 60Hz 1. Open circuit short circuit detection power supply DC 0v-5v 10A 1. 60s charging voltage detection single channel constant current setting range: 0.01a-5a can be set, accuracy < 1%; charging time: 60s ± 0.1s; display setting value; voltage test accuracy: display value ± 1%; 1. ESR test range: 0.0001 - 999.99m ; automatic shift from upper limit of setting value m , , K, M; display mode: LCD display precision: display value 1%; setting mode: it can set the range of gear and display the set value.
Description > Patented transparent thermal protection screen that complies with the IEC A-13 safety standard. > Patented innovative auto water spray to add moisture and have juicier food. > Preset 40�°C (104�ºF) temperature setting for making your own yoghurt. > Intuitive digital control panel with LED display. > 3 preset cooking temperatures. > A complete all-in-one, versatile cooking unit to roast, grill, bake, barbeque, steam, broil, dehydrate, defrost, and air-fry. > Transparent tempered glass lid for food safety. > Cooking temperature ranges from 40�ºC to 260�ºC (104�ºF - 500�ºF). > Increase cooking capacity with extendable hinge arm and extender ring. > Turns off automatically once lid is lifted. > Container loading: 1x20ft Container: 336 pcs 1x40ft Container: 694 pcs 1x40HQ Container: 806 pcs
Description > Large touch control panel with LCD display. > Patented innovative auto water spray to add moisture and have juicier food. > Cooking temperature ranges from 40�ºC to 260�ºC (104�ºF - 500�ºF). > 3 preset cooking temperatures. > A complete all-in-one, versatile cooking unit to roast, grill, bake, barbeque, steam, broil, dehydrate, defrost, and air-fry. > Transparent tempered glass lid for food safety. > Increase cooking capacity with extendable hinge arm and extender ring. > Turns off automatically once lid is lifted. > Container loading: 1x20ft Container: 336 pcs 1x40ft Container: 694 pcs 1x40HQ Container: 806 pcs
Multifunctional vegetable cutter Model: SH-118 Motor: 2.5HP Machine size: 1300 * 650 * 1340MM Machine weight: 200KG Electric power: 1.87KW Power supply: 220-240V / PH Mechanical feeding height 750MM Mechanical conveying discharge height 450MM Conveyor belt width (short / long) 116 / 119MM Conveyor belt length (short / long) 790 / 1645MM Cutting size 1-35MM (double knife) / 1-70MM (single knife) Output 500-2000KG / H Uses: leaf vegetable 1-60MM cut section adjustable, rhizome vegetable sliced diced Roots: Potatoes, dumplings, sweet potatoes, melons, bamboo shoots, onions, eggplant chunks cut into diced, shredded pieces. Leafy vegetables: celery, Chinese cabbage, cabbage, spinach, etc. cut into long strips, cut into small pieces, slices, and strips. Especially suitable for unit canteens and catering companies. Features: 1. Removable belt feeding system, easy and fast cleaning 2. The conveyor belt is made of PU material. 3. Combined electrical switch, exquisite workmanship, comfortable damping feel. 4. The double-blade rotary blade is a double-blade chopping knife. 5. The new cutter head structure can prevent the blade from colliding and producing knocks. 6. Waterproof device is installed in the machine, the circuit is controlled separately, and the failure rate is lower. This machine has four sets of knives: 1 set for diced bulbs, shredded and sliced, and 1 pair of large knives for leaf-cutting vegetables. Diced specifications: 8, 10, 12, 15, 20MM, Cutting specifications: 2,3,4,5,6,7,8MM, Slicing specifications: 2, 3, 4, 5, 6, 7, 8, 10, 12, 15, 20
Name: High-speed French Fries Machine Model: ST-1000 Output: 1000kg/hour Voltage: 380V Power: 0.75 KW Weight: 115kg Size: 1060*690*1040MM The high-speed French fries machine can cut potatoes, sweet potatoes, radishes, etc. into square strips. After cutting, the surface of the finished product is smooth and well-proportioned. The cutting speed is fast and the output is high. The average output per hour reaches more than 1000 kg. The operation is simple, the cleaning is convenient, the time and effort are reduced, and the labor cost is reduced. Used in manufacturing or food processing plants.
Name: High-speed French Fries Machine Model: ST-1000 Output: 1000kg/hour Voltage: 380V Power: 0.75 KW Weight: 115kg Size: 1060*690*1040MM The high-speed French fries machine can cut potatoes, sweet potatoes, radishes, etc. into square strips. After cutting, the surface of the finished product is smooth and well-proportioned. The cutting speed is fast and the output is high. The average output per hour reaches more than 1000 kg. The operation is simple, the cleaning is convenient, the time and effort are reduced, and the labor cost is reduced. Used in manufacturing or food processing plants.
Name: High-speed French Fries Machine Model: ST-1000 Output: 1000kg/hour Voltage: 380V Power: 0.75 KW Weight: 115kg Size: 1060*690*1040MM The high-speed French fries machine can cut potatoes, sweet potatoes, radishes, etc. into square strips. After cutting, the surface of the finished product is smooth and well-proportioned. The cutting speed is fast and the output is high. The average output per hour reaches more than 1000 kg. The operation is simple, the cleaning is convenient, the time and effort are reduced, and the labor cost is reduced. Used in manufacturing or food processing plants.
Description: Peanut seasoning machine a kind of rotating drum with octagonal shape, this kind of shape ensure there is no peanut residual inside of drum. The rotation can be any angle, seasoning coating machine is for final glossy coating, adding different flavor. Hot roasted & fried peanuts are put into seasoning drum for evenly flavor adding, the process needs 4-5mintes, then coated peanuts will be sent to dryer or settle aside for natural drying. Features: Simple & smart structure Easy to use Varous speed controlled Food grade material Parameters: Item: Specifications Capacity: 20kg/batch, 5min/batch Rated voltage: 380V/50~60HZ Rated power( kw): 0.4 Installation Size(mm): 1030Ã??860Ã??1570 Weight: 170kg
Description: Roasting is a typical process that uses hot air to heat peanuts evenly, roasting enhances peanut indicating different roasting result, thus can satisfy various production, e.g. whole peanut blanching, split peanut blanching, peanut chopping, peanut coating, peanut butter grinding, peanut candies, and peanuts frying production. Principle: Multifunctional Roaster use 3 variable factors to control roaster and realize the optimized result, 1.roasting temperature is from 95-180�°C (200 �°F to 360 �°F), 2.roasting belt speed is from 25-40hz, 3. Thickness of material is from 4-10mm. It is a continuous and fully automatic roasting process from feed peanuts to roasted peanut comes out. Commonly we divide roaster into high temperature roasting area, transition area and cooling area. During roasting is undergoing, peanuts stay on the perforated stainless steel conveyor belt, hot air comes from top gas burners, is blown by air blower to the top of conveyor belt, at the same time, we equip with blade type wheel to distribute hot air evenly to everywhere of conveyor belt, at the same time, another hot air blower on the bottom of roasting belt is blowing hot air from bottom side, it occurs hot air recycle inside, the hot air flow can ensure each peanut is heated evenly & entirely. After roasting finishes, peanut goes into cooling area via transition area, high pressure cold air from outside can bring the heat of peanuts away and cool down the surface temperature to room temperature.
Description: The roaster utilizes heat radiation principle to archieve the roasting & drying purpose. The heating power can be gas/electricity, combustion using butane gas at the bottom of drum, then nut material is heating inside of roaster drum, hence finishes heat exchange (electricity type adopts heating elements to work on the drum body, then inside material is heated). A motor reducer is equipped on the back of roaster to drive the drum rotating, it has two ways-: positive direction is for feedin, the opposite direction if for output. There also has screw plate inside of drum to push the peanut forward and backward evenly, thus cause the peanut roasted equally. Structure: Frame, housing, moving parts, shaft made of mild steel, for strong durable purpose (If process involves salty/chemical ingredient, please let us know) - Drum made of stainless materials mesh - Coverage of flames by the panels fitted with ventilation - Side panel insulation with glass wool - Roasting temperature and time could be set on request - Control panel with temperature indicator and controller, auto ignition button for gas, start/ stop button, emergency shut off button etc - With operating manual in English Parameters: Roaster Type: Gas heated Capacity: 100kg/ batch (kernel) 60kg/batch (in shell) Rated voltage: 380V/50HZ Rated power: 1.1kw Working Temperature: 160-220�°C Gas consumption: 6-83/hr Outer dimension(L*W*H): 2800�?1220�?1900mm(L�?W�?H) Weight: 950/1000kgs Roaster Type: Electricity heated Capacity: 100kg/ batch (kernel) 60kg/batch (in shell) Rated voltage: 380V/50HZ Rated power: 2kw+22.5kw Working Temperature: 160-220�°C Outer dimension(L*W*H): 2800�?900�?1250mm(L�?W�?H) Weight: 820/870kgs
Description: Wet Peanut Blancher is designed to take off the red skin of peanut. First raw peanut kernels are boiled in warm water to make out skin loosen, then feed into wet peanut blancher, fixed by the rubber wheels, there are numerous blades on the rubber wheels, peanuts will be cut slightly, under the squeezing force, peanut and skin will separate, white blanched peanut will fall down to sorting conveyor, the skin will be thrown out by chain wheels. Wet Blancher can also blanch peanut, almond, soybean, broad bean etc. Among salted fried peanut production line, this kind of wet blancher is an important equipment. Parameters: Capacity: 150kg/h Power: 0.55kw Performance: Peeling rate: 98%�±2 Broken rate: â?¤3% Whole Nut Rate: 85%�±5 Size: 960*650*1080mm Weight: 200kg Capacity: 200kg/h Power: 0.75kw Performance: Peeling rate: 98%�±2 Broken rate: â?¤3% Whole Nut Rate: 85%�±5 Size: 1110*810*1140mm Weight: 250kg Capacity: 250kg/h Power: 0.75kw Performance: Peeling rate: 98%�±2 Broken rate: â?¤3% Whole Nut Rate: 85%�±5 Size: 1200*930*1140mm Weight: 270kg
Description: HJ Peanut Sheller Machine is designed to shell raw, sunâ??dried groundnuts, split the hard shell and peanut kernels via the especial structure which is built by shelling grates and concaves. It is ideal choice for peanut farmers, householders and small cooperatives. Principle: The peanut sheller is designed with two shelling drums (Model HJ1600) or three shelling drums (Model HJ3500, HJ4500 and HJ6000). The peanut are feed to the first drum, under the beaten of shelling grates and concaves, the shells and kernels are separated, then firstly shelled nuts flow to the vibrating sifter for separation, light shells are blown by air blower,heavier peanut kernels go to outlet, at the same time, under the function of vibrating gravity sifter, the small percentage of unshelled peanuts will flow into the second outlet and feed into 2nd drum for repeated shelling process until it is shelled. Advantage: 1. It has 3-4 rollers for shelling, different shapes of rasp bars, the function of sorting and sieving, second shelling makes the machine with high shelling ratio and low breaking ratio. 2. Because HJ Peanut sheller sort peanut into two grades by sorter, small peanut and big peanut, then sorted big and small peanut goes separately to their fitted shelling device according to the size, so the shelling ratio is higher. 3. And also because the unshelled peanut will return to shelling device for second shelling, finally peanuts can be totally shelled . 4. Accepts a wide range of nut sizes and suitable to process various cultivated varieties of peanuts from all over the world.. 5. With the humanization design, shell slag can be removed automatically. 6. The shelling machine is equipped with pneumatic conveyor that transfers the groundnuts without injured. In addition, the dust collector can be added in order to keep the working environment clean.
Darin is a fast growing manufacturer for automatic food processing machine since 2011. The leading machine -- Cereal Bar/Granola Bar/Muesli Bar/Peanut Candy/Sesame Candy/ Making Machine to Make Granola Bars, Nuts Bars,Seeds Bars etc.with the raw material of rice, millet, wheat, highland barley, fagopyrum tataricm Gaertn, maize, broomcorn, Chinese pearl barley, buckwheat, etc. Darin Makes Business Easier. #proteinbarmachine #energybarmachine #peanutbarmachine #cerealballformingmachine #fruitbarformingmachine #cerealbarmoldingmachine #candybarmachine #snacksbarmoldingmachine #peanutchikkimachine #chikkibarmachine #mueslifitmachine #fitnessbarmachine #granolabitesmachine #fitbarmachine #nutsbarmachine #granolabarmachine
battery cell sorting machine Contact: JESSIE AT SAWATECH DOT COM DOT CN spot welding machine for 18650 battery spot welding machine for 18650 pack or 18650 cell pouch low speed car and E-bike battery pack automatic line power tool and garden tool battery pack auto production line lithium battery cell spot welding machine battery cell auto sorting machine auto label barley paper machine power tool lithium battery assembly line auto soldering machine 18650 li ion battery welding machine
This stainless steel kurkure slanty frying machine is one automatic frying machine, with the function of automatic discharging, gas or electric heating, automatic stirring. The main body of machine uses SUS304 stainless steel. This is multi-purpose frying machine can fry kurkure, slanty, namkeen, cheetos, murukku Chakli, bonda, potato chips, french fries, banana plantain chips, etc
This vegetable and fruit washing peeling machine is mainly for wahsing and peeling potato, carrot, sweet potato, cassava, taro, yam, ginger, white radish, apple, peach, etc. The round and microscler vegetables and fruits. This brush type vegetable fruit washing peeling machine is with large effective volume, high efficiency, water saving, suitable for the continuous cleaning operations.
Automatic Frozen French Fries Machine|Cassava Potato Sticks Processing Plant is mainly used to produce potato french fries using fresh potato, which can be used to process frozen french fries or pre-fried fries. The complete french fries production line is consisted of Potato washing peeling machine, french fry cutter machine, blanching machine, air dewatering machine, french fries fryer Machine, vbrate de-oil machine, air drying machine, french fries flavoring machine and packaging machine.
The complete potato chips production line/potato crisps manufacturing equipment is all made of 304 stainless steel. The same set of potato chips machinery can also be used to make plantain chips only chaging the peeling machine. 1.Elevator, 2.Washing and peeling machine, 3.Picking line, 4.Elevator, 5.Potato cutting machine, 6.Rinsing line, 7.Blanching machine, 8.Dewatering machine, 9.Oil-water mixed frying machine, 10.Vibration de-oiling, 11.De-oiling machine, 12. seasoning machine, 13. Picking line, 14. Automatic potato chips pacakaging machine.
The BW2000 model walnut processing line is design for cracking walnut and get pure kernels. The machine consisits of huller, pre-separator, un-hulled cycling system, inspection belt, kernels grading machine, et. We tested varieties like Sunland, Payne, FRANQUETTE, Eureka with very satisfactory performance. The unique three-point-cracking technology enables a precise handling to get higher yield of butterfly kernels. For more information, Please contact with our staff.
