Dekelon produces high speed facial tissue machines in various models. This paper machine is ideal for making different varieties of tissue papers in a nominal grammage of 13-30g/m² from wood pulp board, waste paper, timber, bamboo, rice straw, bagasse and other pulp. It can serve as both a facial tissue machine and napkin machine, can used to produce roll toilet paper, facial tissue, napkin, paper towels and more, at a maximum speed of 300m/minute, a breadth of 1575-3600mm, and a daily output of 5-20t. The main equipment structure: 1. Back rolls: f380 × 2100mm of one set, including bearings, bearing pedestal, stand column, bolt, and the thickness is 15mm, hardness is 95 ° ± 2 ° with bearings 312. 2. Cylinder section: f1250mm×1950mm stainless steel cylinder mould 2 sets, including frame, bearing shells, bearing pedestal, bearing 3615, f380 × 2000 couch roll 2 sets, the rubber hardness is 38 ° ± 2 °, thickness is 25mm, with bearings 312. 3. Water squeezing section: smooth rollf270 × 2100 one set and bottom rubber rollerf270 × 2100mm one set, equipped with bearings 113513, with two groups of lever pressure device. 4. Touch roll section: f450 × 2000 one touch roll, rubber hardness is 95 ° ± 2 °, and the thickness is 23mm, the crown is 0.6mm, with a good supporting arm, two groups off320 three pneumatic tire pressure device, with bearing 113622 and one set of air control box. 5. Main press section: natural granite stone rollf500 × 2000mm one set, equipped with a scraper, and af450 × 2000 rubber roller, the rubber hardness is 90 ° ± 2 °, thickness is 23mm, the crown is 0.5mm, with bearing 113622/113622 , and a good press arm, f250 two groups of cylinder pressure device, and one set of air control box. 6. Gloss section: f400 × 2000 a calendar rubber roller, rubber hardness is 95 ° ± 2 °, thickness is 20mm, equipped with 113620 bearing and support, arm, spanner positive and negative pressure device two groups.
Dekelon produces high speed facial tissue machines in various models. This paper machine is ideal for making different varieties of tissue papers in a nominal grammage of 13-30g/m² from wood pulp board, waste paper, timber, bamboo, rice straw, bagasse and other pulp. It can serve as both a facial tissue machine and napkin machine, can used to produce roll toilet paper, facial tissue, napkin, paper towels and more, at a maximum speed of 300m/minute, a breadth of 1575-3600mm, and a daily output of 5-20t. The main equipment structure: 1. Back rolls: f380 × 2100mm of one set, including bearings, bearing pedestal, stand column, bolt, and the thickness is 15mm, hardness is 95 ° ± 2 ° with bearings 312. 2. Cylinder section: f1250mm×1950mm stainless steel cylinder mould 2 sets, including frame, bearing shells, bearing pedestal, bearing 3615, f380 × 2000 couch roll 2 sets, the rubber hardness is 38 ° ± 2 °, thickness is 25mm, with bearings 312. 3. Water squeezing section: smooth rollf270 × 2100 one set and bottom rubber rollerf270 × 2100mm one set, equipped with bearings 113513, with two groups of lever pressure device. 4. Touch roll section: f450 × 2000 one touch roll, rubber hardness is 95 ° ± 2 °, and the thickness is 23mm, the crown is 0.6mm, with a good supporting arm, two groups off320 three pneumatic tire pressure device, with bearing 113622 and one set of air control box. 5. Main press section: natural granite stone rollf500 × 2000mm one set, equipped with a scraper, and af450 × 2000 rubber roller, the rubber hardness is 90 ° ± 2 °, thickness is 23mm, the crown is 0.5mm, with bearing 113622/113622 , and a good press arm, f250 two groups of cylinder pressure device, and one set of air control box. 6. Gloss section: f400 × 2000 a calendar rubber roller, rubber hardness is 95 ° ± 2 °, thickness is 20mm, equipped with 113620 bearing and support, arm, spanner positive and negative pressure device two groups.
Our tissue rewinding machine can be divided into fully automatic and semi-automatic types. The fully automatic tissue rewinder comes with a computer control system. Fully Automatic Tissue Rewinder Using computer programming technology, the fully automatic tissue rewinding machine achieves an automatic change of the paper tube or coreless roll paper, and auto gluing, sealing, and trimming. This reduces labor intensity and increases the product quality. Semi-Automatic Tissue Rewinder The semi-automatic tissue rewinding machine relies more on manual operation. With only a slight difference in the operation conversation, there is very little difference between this and the automatic rewinder. Main Features 1. The fully automatic tissue rewinder is available with a double face embossing unit that makes the tissue softer, while keeping a uniform embossing effect on each face and firm lamination. This paper converting machinery is ideal for processing rolls for kitchen use. In addition, the end product comes with 15% or more weight reduction than those with the same size, but a single face embossing. 2. Therewinding equipment can be equipped with special units for a complete and quick switchover between coreless, solid, and hollow tissue rolls. This change over is optional according to customer requirements. 3. Our tissue rewinding machine can synchronously complete automatic trimming, gluing, sealing, and roller drawing out, enabling the paper to smoothly enter the slitter and packaging unit without sheet loss. Because of this, it can improve the production efficiency and product grade. 4. This tissue rewinder uses a pneumatic belt paper feeder. It is designed with tension control devices for unwinding rollers and each paper roll.
The ZSM series coarse refiner is a great choice for the coarse grinding of pulp raw materials and re-pulping of broke and waste paper. This paper mill equipment is also suitable for the refining of continuous fiber pulps such as cotton pulp, wood pulp and helm pulp.Capacity: 10-30 T/D Features of the Coarse Refiner 1. The pulp equipment comes with a long refining zone and strong cutting capacity for fiber. 2. It ensures less damage to the fiber capillary, and a homogenous refining result. The materials will be ground roughly before entering the defibering zone, thus ensuring the paper has a high fracture length, tearing strength, and breaking strength. 3. The conical refiner features a low energy consumption, high production capacity high efficiency, low noise and easy maintenance. 4. It is equipped with both manual and electric operating devices.
The ZSM series coarse refiner is a great choice for the coarse grinding of pulp raw materials and re-pulping of broke and waste paper. This paper mill equipment is also suitable for the refining of continuous fiber pulps such as cotton pulp, wood pulp and helm pulp.Capacity: 10-30 T/D Features of the Coarse Refiner 1. The pulp equipment comes with a long refining zone and strong cutting capacity for fiber. 2. It ensures less damage to the fiber capillary, and a homogenous refining result. The materials will be ground roughly before entering the defibering zone, thus ensuring the paper has a high fracture length, tearing strength, and breaking strength. 3. The conical refiner features a low energy consumption, high production capacity high efficiency, low noise and easy maintenance. 4. It is equipped with both manual and electric operating devices.
This wrapping/packaging paper machine is designed for both single and double layers. It comes in a variety of models, including the 1092 type, 1575 type, 1760 type, 1880 type, 2100 type, 2400 type, 2880 type, 3200 type,3600 type,4200 type and 4800 type. The number represents the machine deckle. It can also be equipped with a relevant device, according to paper grammage, machine speed, output, and other parameters. The main equipment: 1. Pulp-flowing box: It adopts open-type pulp-flowing box, consisting of pyramid tube, staircase diffuser, distributing roller and box body. Staircase diffusion orifice plate pulp distributor is three-stage diffusion, which made of organic glass and upper and lower lip plates made of stainless steel. The upper lip plates can do full and local adjustment is three-stage diffusion. 2. Fourdrinier part: Wire table is 18000mm. Except draw-out seat made of alumina alloy, table rack is all welded by section steel with 1.5mm stainless steel cladding. Wire part is mainly composed of chest roller, forming board, wire-driving plate, water scrapping board, moisture absorbing box, and vacuum water-absorbing box, vacuum roller, wire-driving roller, electrical wire-tighter, pneumatic corrector, constant-tension wire-tighter, incision needle and margin raising device. 3. Press part: It adopts vacuum absorption injection paper, one streak of vacuum pressing and three streaks of pressing. 4. Drying part: It is set 28 pieces of f1500mm drying cylinders, including one f3000mm big cylinder of array type, 6+6+8+1+glueing machine+8 driven by enclosed gear box and lubricated by sparse oil. 5. Driving and control part: It adopts AC frequency conversion speed, drive step by step. Hard tooth surface gear box connected by universal coupling is used, and entire digital closed circle control system is used. 6. Press-polishing and paper reeling: It adopts super press polishing machine and level paper reeling machine.
This wrapping/packaging paper machine is designed for both single and double layers. It comes in a variety of models, including the 1092 type, 1575 type, 1760 type, 1880 type, 2100 type, 2400 type, 2880 type, 3200 type,3600 type,4200 type and 4800 type. The number represents the machine deckle. It can also be equipped with a relevant device, according to paper grammage, machine speed, output, and other parameters. The main equipment: 1. Pulp-flowing box: It adopts open-type pulp-flowing box, consisting of pyramid tube, staircase diffuser, distributing roller and box body. Staircase diffusion orifice plate pulp distributor is three-stage diffusion, which made of organic glass and upper and lower lip plates made of stainless steel. The upper lip plates can do full and local adjustment is three-stage diffusion. 2. Fourdrinier part: Wire table is 18000mm. Except draw-out seat made of alumina alloy, table rack is all welded by section steel with 1.5mm stainless steel cladding. Wire part is mainly composed of chest roller, forming board, wire-driving plate, water scrapping board, moisture absorbing box, and vacuum water-absorbing box, vacuum roller, wire-driving roller, electrical wire-tighter, pneumatic corrector, constant-tension wire-tighter, incision needle and margin raising device. 3. Press part: It adopts vacuum absorption injection paper, one streak of vacuum pressing and three streaks of pressing. 4. Drying part: It is set 28 pieces of f1500mm drying cylinders, including one f3000mm big cylinder of array type, 6+6+8+1+glueing machine+8 driven by enclosed gear box and lubricated by sparse oil. 5. Driving and control part: It adopts AC frequency conversion speed, drive step by step. Hard tooth surface gear box connected by universal coupling is used, and entire digital closed circle control system is used. 6. Press-polishing and paper reeling: It adopts super press polishing machine and level paper reeling machine.
Semi-Automatic Tissue Rewinder The semi-automatic tissue rewinding machine relies more on manual operation. With only a slight difference in the operation conversation, there is very little difference between this and the automatic rewinder. Fully Automatic Tissue Rewinder Using computer programming technology, the fully automatic tissue rewinding machine achieves an automatic change of the paper tube or coreless roll paper, and auto gluing, sealing, and trimming. This reduces labor intensity and increases the product quality.
kraft paper and corrugated paper uses wood pulp board, waste paper, timber, bamboo, rice straw, bagasse, and other pulps to produce the paper at 50 to 300g/m². The machine is primarily used to make Kraft paper, corrugated paper, cardboard paper, and more. Trimmed width of the paper ranges form 1092mm to 3300mm. The design capacity of the packaging and wrapping paper machine is 10-150t/d. This packaging paper machine is designed for both single and double layers. It comes in a variety of models, including the 1092 type, 1575 type, 1760 type, 1880 type, 2100 type, 2400 type, 2880 type, 3200 type,3600 type,4200 type and 4800 type. The number represents the machine deckle. It can also be equipped with a relevant device, according to paper grammage, machine speed, output, and other parameters. 1. 3600mm type Paper Machine Technical Parameters Paper variety: Kraft paper, corrugated paper, cardboard paper Grammage: 50~300g/m Working speed: 350m/min Design speed: 500m/min Capacity: 75~100T/ Rail distance: 4700 mm Driving method: AC Variable frequency speed control, sectional drive Machine type: Heavy square box type, with left and right machine available Standard: International export standard
Dekelon paper machine for printing and writing paper production. It can be used to make A4 paper, newsprint paper, writing paper and more, in 50-300g/m² from wood pulp, waste paper, wood and other pulp. The design speed of this newsprint paper machine is 300m/min, and the breadth is 1092-4100mm. Structural Features of the Paper Machine 1. Headbox This paper making machine is designed with an open headbox, which is composed of the taper pipe, stepped diffuser, rectifier roll and box. The pulp distributor with a pore plate made of organic glass comes with three step diffusion. The top and lower lips of the slice are made with stainless steel. The top lip has full and local control. 2. Forming Section (Wet End) The fourdrinier table has a length of 18,000mm. With the exception of the bearing block, which is made of aluminum alloy, the rack is completely constructed from structural steels by welding, and covered by a layer of stainless steel at a 1.5mm width. The forming section of the paper machine consists of the breast roller, forming board, foils, suction boxes, vacuum couch roller, electric wire tightener, pneumatic corrector, and edgy warping device. 3. Press Section In the press section, the fourdrinier machine uses a vacuum suction pickup roller and three suction rolls. 4. Dryer Section This paper machine is equipped with 28 sets of f1500mm steam-heated cylinders and one f3000mm cylinder in the dryer section. Paper dryers are typically arranged in groups. The arrangement pattern is, in sequence: 6 dry cylinders, 6 dry cylinders, 8 dry cylinders, 1 dry cylinder, glue applicator and 8 dry cylinders. They are driven by a sealed gearbox and lubricated with a thin oil. 5. Drive and Control Section This paper machinery uses a sectional drive system composed of an AC variable frequency motor, reduction gearbox with a hard teeth surface, and universal spindle coupling. It comes with an all-digital closed loop control system. 6. Calender Press Polish and Rewinding Dekelon's printing and writing paper machine applies a super calender and horizontal paper winding machine.
Dekelon's KDC series low density cleaner is a high quality and performance pulp detrasher. It is characterized by a small floor space, easy operation, high purification efficiency, wear and pressure resistance, and a long service life. For customers that need a detrashing system for purifying pulp with a low consistency, this series of pulp cleaners is an excellent choice. According to specific gravity differences between fibers and impurities, the impurities can be separated from the pulp at the bottom of the cleaner under centrifugal force. The impurities and purified pulp will then be discharged separately from different ports. Capacity: 4~20t/d
The disc thickener from Dekelon, is used in the pulp and paper industry for dewatering and thickening low consistency paper pulp. Not only can this gravity thickener be used to thicken wood, cotton and straw pulp, it is also suitable for filtration and thickening applications in other industries. compared to other types of fiber suspension thickeners and other existing dewatering and thickening equipment, our disc thickeners feature a simple structure, easy installation and maintenance, a high production capacity, wide pulp adaptability and more. They have become increasingly popular among the pulp and paper industry. According to the specific location of the drive part, the thickening machine has two arrangement modes. If the user is facing the outlet and sees the drum, and the drive part is on the right, the machine is a right hand thickener, represented by "Y." On the flip side, if the drive part is located at the left, it is called a left hand thickener, represented by "Z."
The ZGS series high consistency pulper is mainly used for pulp board and is primarily used for pulp board and waste paper disintegration, broke and waste paper deinking, and pulp purification. The capacity of this high consistency pulping system is 3-80t/d. Under a high consistency, this pulper can achieve a rapid waste paper disintegration and deinking. Due to its large production capacity, low energy consumption, steam and chemical economy, easy maintenance, long service life, low noise, small vibration and stable operation, it saves up to 50% in water and energy. this equipment is mainly used to degrade pulp board, waste paper and broken paper, deinking and pulp purification.
Dekelon also provides paper machines for the production of specialty paper, included regenerated leather, asphalt paper, grey board, sealing gasket paper and filter paper. The specialty paper is made from the leftover material of various leather, scraps from the buffing machine, waste fibers and more, which are first processed into pulp and then formed into a paper sheet with a width of 0.6-5mm on the fourdrinier table. After this, the paper sheet undergoes dewatering, pressing, drying, polishing, flattening, cutting, winding and packaging in the specialty paper machine. >applications The specialty paper production line is widely used for different leather products, including leather bags, belts, clothes, sofas, shoes and more.
Place of Origin: Guangdong, China (Mainland) Brand Name: Colefa or your logo Model Number: washable kraft paper backpack Material: washable kraft paper Capacity: 30 - 40L Type: Softback Use: Day Backpack Item: 2016 hot selling new design washable kraft paper backpack Logo: OEM Size: customized Color: As the pic (customize if order meet MOQ) MOQ: 1000 Pcs per style Sample lead time: 7-10 days Bulk order lead time: 30 or 40 days after get deposit Term of Payment: 30% deposit + 70% balance when fax BL by TT Shipment: By air; By carrier depend on QTY Printing: Embroidery, Silkscreen printing, Metal etc.. Carton size:60*40*40CM,Qty:100pcs/ctn,1pcs/oppbag
Woven label with endfold 1000pcs per box
matte paper hangtag with line strings 50pcs for one pack
cotton/satin background with printed logo with endfold 1000pcs per box
real suede leather patch 100pcs per bag
alloy metal logo with the real leather patch 100pcs per bag
