Hudson is an old purchaser of LARZEP company in Spain. He cooperates with us on are some non-standard hydraulic sequence valves, and often discuss some difficult and miscellaneous problems of hydraulic sequence valves with us. In the second half of last year, their company developed a machine tool hydraulic system, which uses the hydraulic sequence valves to implement the device of positioning first and then clamping. In order to save development time, Hudson purchased directly from Spanish hydraulic sequence valve manufacturers. According to the hydraulic sequence valve drawings provided by Hudson, the factory delivered 20 hydraulic sequence valve samples in 30 days. After the test run, it was found that the positioning clamping device reacted slowly after the machine tool was started. Check the oil circuit and components of the whole hydraulic system one by one, and there is no abnormality. Their engineers speculated that there was a problem with the hydraulic sequence valves. Hudson contacted the original factory. The manufacturer fed back that the samples of hydraulic sequence valves were completely produced according to the drawings provided by LARZEP company, and the dimensional accuracy met the requirements. Their engineers tested the hydraulic sequence valves separately and there was no abnormality. Hudson's team explored for 2 days and determined that there was a problem with the design of the hydraulic sequence valves. Hudson contacted AAK because the hydraulic sequence valve problems encountered several times before were solved by AAK. According to his fault description, drawings of hydraulic sequence valve, working parameters of hydraulic system of machine tool and video of test run, AAK engineer did find the problem in the design of hydraulic sequence valve. AAK engineer's suggestion is to change the design mode of the hydraulic sequence valve to maintain a minimum "pilot pressure" in the starting circuit and "fully open" when it is higher than the set pressure. This feature can effectively reduce the throttling loss of the system under the working pressure and make the clamping and positioning system of the machine tool sensitive. Hudson team had to stop the machine test and let AAK immediately test the sample according to AAK design recommendations. After 30 days, AAK sent 20 hydraulic sequence valve samples and provided our working schematic diagram. Hudson team installed and commissioned the machine tool after receiving it, and the machine tool was continuously tested for 48H. The reaction of the positioning and clamping device of the machine tool has always been normal. Hudson emailed us that AAK newly designed hydraulic sequence valve was more reliable than their native Spanish ones, and their engineers were surprised by AAK design ability. Thanks to the help of AAK, they succeeded in the test run.
AAK, as a manufacturer of producing hydraulic valves, has been doing ODM hydraulic valves for 10 years for 3 of the world's top 500 in the industry. In the years of labeling these big brand hydraulic valves, the overall quality of the factory has improved significantly. The operation of each workshop is standardized, the quality control process of hydraulic valves is strict, and the self-implementation is more strict than the ISO certification system, being meticulous in making hydraulic valves. All of these are valuable assets for big brand ODMs. In cooperation with these big brand hydraulic valves, AAK has formed a strict process flow, because of them, there is the growth of AAK hydraulic valves. The strength of the factory has improved, and it is natural for the market to respond. I still remember that 10 years ago, I participated in the Ningbo hydraulic valve industry seminar. An old engineer said at the meeting: "It is easier for factories to succeed in making more difficult hydraulic valves". This seems to be in line with our traditional experience: No cross, no crown. That sounds right, but it's not true. Because there is also a contrary saying called "follow the trend". If a hydraulic valve manufacturer does the right thing, it is not only easy to succeed, but also not difficult. The experience of AAK hydraulic valves over the years is the same. If some styles of hydraulic valves are easy to do, you do not feel particularly difficult and can get help everywhere, they are more hopefully to be successful. I think that if you put the difficulty and success of the hydraulic valves together, and want to find the causal relationship between them, this idea itself has a problem. If you put the difficulty of hydraulic valves and the growth together, it may be right. The success of making a hydraulic valve with appropriate difficulty is not certain, but it will lead to our growth for sure. If we make this hydraulic valve, it will be helpful to our technological growth, and AAK will do it without hesitation. Ten years ago, China's hydraulic valves were almost supplied to some domestic manufacturers of mechanical equipment, perhaps because of the simple process or the trend of hydraulic valve manufacturers. At that time, AAK hydraulic valves began to be tested by HydraForce. At that time, it was difficult to find a third manufacturer who could understand English hydraulic valve drawings in Ningbo. Five years ago, international equipment manufacturers, industrial manufacturers and hydraulic valve brands began to purchase hydraulic valves from China. AAK hydraulic valve was the first to try tomato. AAK hydraulic valve has been doing ODM hydraulic valves for 3 of the world's top 500 in the industry for 10 years. The quality control process of hydraulic valves is strict, which is more strict than the ISO certification system. It is meticulous in making hydraulic valves.
Carter comes from an manufacturing company in , and the purchase of hydraulic needle valves has been smooth in recent years. At the beginning of last year, an excavator sold by their company for less than 6 months was complained by customer. The boom of the excavator falls too fast due to its own weight, which is easy to cause danger. Their technician found that there was a problem with the hydraulic needle valve of the hydraulic system. There were obvious wear marks at the contact point between the valve spool and valve seat of the hydraulic needle valve, which was easy to leak. The leakage of the hydraulic needle valve will cause the oil saving and speed limiting circuit of the hydraulic cylinder to be uncontrollable. The boss was very angry that the equipment sold for only half a year was complained and asked Carter to find out the cause of the hydraulic needle valve problem and solve it. Carter contacted the original manufacturer of the hydraulic needle valves and requested to replace the hydraulic needle valves. The manufacturer said that the service life of hydraulic needle valves under 450bar working condition is basically 6 months. The only way to solve this complaint is to replace the hydraulic needle valves every 6 months. Such reply made Carter speechless, because his customer would not accept the high-frequency replacement of hydraulic needle valves, which not only brought a bad user experience, but also the after-sales cost was not cheap. Carter contacted all of his hydraulic needle valve suppliers, and they all replied that they were not sure to achieve a hydraulic needle valve with a service life of 1 year under the working condition of 450bar. When browsing the website, he found and left a message on the How long is the service life of hydraulic needle valves with pressure resistance of 450bar We replied directly for 1 year or more. The next day, he told the problems encountered in purchasing hydraulic needle valves at the beginning of last year in detail. After receiving the drawing of the hydraulic needle valve, we found that the hydraulic needle valve needed by Carter has much higher requirements than the ordinary hydraulic needle valves. We replied that will select specific materials for samples, which can ensure that the hydraulic needle valves can be used for more than 1 year under normal conditions. If possible, he can directly test the samples.
George comes from a hydraulic valve company in Germany. He likes to choose old suppliers to place orders. Some time ago, he placed an order of hydraulic pressure control valve with machining allowance of 0.3mm with an old supplier. After 3 proofing, his customer still did not approve the samples of the hydraulic pressure control valve. George was very angry. Before ordering this hydraulic pressure control valve, he confirmed the parameters with the manufacturer several times, especially the machining allowance of 0.3mm. The manufacturer guaranteed no problem. Unexpectedly, the accuracy error of the hydraulic pressure control valve sample was 10% higher, and even after revising samples for 3 times, it still can not meet the machining allowance of 0.3mm. George has to face the technical shortcomings of the old manufacturer, the sample pushing of the customer, and the situation of no suitable hydraulic pressure control valve manufacturer to make samples. He contacted the all the hydraulic valve manufacturers cooperated in the past, but none of them was able to make a hydraulic pressure control valve with a machining allowance of 0.3mm. He kept looking for a new hydraulic pressure control valve manufacturer online and came across AAK hydraulic valve on B2B. George left a message on our website www.aakindustry.com: I saw AAK article introducing the hydraulic valve with machining allowance of 0.3mm. We have a hydraulic pressure control valve requiring machining allowance of 0.3mm. Can you sample it? For those customers who directly require to make samples like this, basically, they encountered the sample failure from other hydraulic pressure control valve manufacturers. After communication, we know that his old supplier has failed to deal with the 0.3mm finishing hydraulic pressure control valve samples for 3 times. After checking George's hydraulic pressure control valve drawings and various parameter descriptions, AAK engineers confidently informed that the sample could be successful at one time. George may think that only AAK can help him solve the problem. He directly paid a proofing fee of $1,200.00 and asked us to send the hydraulic pressure control valve samples within 3 weeks. We appreciated George's frankness and asked the workshop to cooperate fully. After 15 days, we successfully sent the samples of hydraulic pressure control valves. On the third day after George received the samples, he told us that the machining accuracy of AAK hydraulic pressure control valve not only met the requirement of machining allowance of 0.3mm, but also increased by 5%, which made him admire very much. In order to ensure the accuracy of finish machining size allowance, the heat treatment process is the most critical step. At present, most hydraulic pressure control valve manufacturers adopt local quenching, the workpiece heat treatment process is not easy to control, and most of them are easy to deform.
Over the past year, Jerome has purchased more than 20 batches of different types of hydraulic valves of test orders from more than 10 hydraulic valve manufacturers in Ningbo, including AAK. Finally, he chose to place the large order of hydraulic flow control valves with AAK, because the packaging details of AAK made him think that the quality of AAK hydraulic flow control valves is the most reliable. Jerome is from a hydraulic equipment company in Italy. He sent an email last week to purchase 2,500 hydraulic flow control valves. I was surprised because Jerome always purchased small orders before. After e-mail communication, it was learned that Jerome has purchased more than 20 batches of different types of hydraulic valve test orders from more than 10 hydraulic valve manufacturers in Ningbo in the past year. There are always some problems, such as time delay and communication delay, especially the packaging of the test order was criticized by his boss. The quality defect of the hydraulic flow control valves purchased last time was complained to the boss by the company's installation engineer. During the assembly process, the installation engineer found that several hydraulic flow control valves could not be screwed into the socket at all, mainly due to obvious bumps at the threads of the hydraulic flow control valves. Jerome requires the original hydraulic flow control valves to be replaced. The manufacturer believes that each hydraulic flow control valve has been pressure tested before leaving the factory and shipped only after it is qualified. The bump was caused by the carelessness of their installers. The installer showed the boss of the damaged package photos to reveal the reason. Some of the packing boxes of the hydraulic flow control valves are deformed, some are broken, and even some of the inner packing poly bags are broken. Those hydraulic flow control valves with bumps were improperly packaged and protected during transportation. Jerome is helpless because of the factory's prevarication. Fortunately, this is just a trial order. Jerome thought of the packaging details of each trial order of AAK. Only the packaging of AAK was different from that of other hydraulic valve manufacturers in Ningbo. At that time, it was only the trial order that he didn't pay attention to the packaging details of AAK. Now he saw the problems caused by improper packaging during transportation from other hydraulic valve manufacturers. He realized that only each trial order of AAK, the packaging received was intact. Later, I told him that because the quantity of trial orders was small, most of them were delivered by express, and it is unavoidable that the parcels will be bumped. AAK will inspect each hydraulic flow control valve separately when leaving the factory. Only the qualified hydraulic flow control valves are put into the bubble bag and then into the corrugated box with the right size,
Over the past 2 years, Peter, who is from ST hydraulic equipment manufacturing company, has been very smooth in purchasing hydraulic valves in Ningbo. He and I often have some communication via emails, but there is no cooperation yet due to the high price. A batch of hydraulic directional control valves he purchased last year had problems. Six months after shipment, the customer found that the hydraulic system could not operate because the valve spool of the hydraulic directional control valve was stuck, and asked ST company to solve it within 30 days. Peter communicated with the original manufacturer of this hydraulic directional control valve but no gain. The manufacturer thought that the hydraulic oil was not clean or there were problems in installation, because their hydraulic directional control valves passed the test before shipping. The boss asked Peter to check with other manufacturers and be sure to solve customer complaints within 30 days. Most manufacturers advised that they have no existing stocks that are exactly same as this hydraulic directional control valve, and they are also not willing to produce it especially for such a small quantity. Some manufacturer advised that they can customize it for Peter, but it will take more than 50 days and also costs a lot. Two weeks passed but still no solution, which makes Peter haggard. Peter thought of AAK and emailed us to ask if there was a hydraulic directional control valve of the same model, and the faster the delivery, the better. After reading this email, I understood that there was a problem with the hydraulic directional control valves purchased by Peter. After further communication, I learned that the valve spool of the hydraulic directional control valve he purchased this time was easy to be stuck and complained by customer. According to Peter's drawings and working condition requirements, AAK engineers conducted comparative analysis, and later found that the control principle and size of this hydraulic directional control valve are consistent with one of AAK's existing stock, except that the design method is different. I immediately answered Peter that AAK had 100 hydraulic directional control valves in stock. At the same time, I emailed the drawings of AAK hydraulic directional control valves and asked Peter and his engineers to verify whether AAK hydraulic directional control valves met their requirements. The next day, Peter said that their engineers thought AAK hydraulic directional control valve could not be used because some designs were fundamentally inconsistent. I suggested to him: if you want to solve the customer complaint within 30 days, perhaps purchasing this hydraulic directional control valve is the best choice. To believe in the analytical ability of AAK, you should try our hydraulic directional control valves first. If it really cannot be used, AAK shall bear all expenses for goods return.
AAK introduced HARDINGE precision CNC lathe, and the machining surface accuracy of hydraulic relief valves was improved to 0.3m, which can not be reached by nearly 95% of hydraulic valve manufacturers in Ningbo. After comparing the parameters of different factories, a German customer found that only AAK meets their requirements for PO confirmation. Fred, a hydraulic valve purchaser from Brandenburg, Germany, is in urgent need of purchasing a hydraulic relief valve for a forklift recently. This hydraulic relief valve has a very high precision requirement. The machining surface roughness of a conventional valve is generally around 0.8m, but this one needs to reach 0.3m, the precision of which is nearly 3 times higher. Fred contacted all his hydraulic relief valve manufacturers, but none of them could achieve an accuracy of 0.3m. It is difficult for Fred to find a solution. Fred decided to try through B2B. He contacted nearly 10 hydraulic relief valve manufacturers online. Two said they could try it, but they are not sure for 100% success, because they had never made such a high-precision hydraulic relief valve. It seems that Fred has no good choice and asked them to try samples. Three weeks later, due to the insufficient accuracy and stability of the hydraulic relief valve, the customer did not approve the samples from these two manufacturers and asked Fred to re-proofing. Fred had to find other new manufacturers of hydraulic relief valves. Fred saw AAK hydraulic valve on B2B and left a message on our can you make the hydraulic relief valves with accuracy of 0.3m? I noticed that he browsed AAK website for about half an hour. He should have encountered problem on accuracy. We reply that it depends on the parameter index of the hydraulic relief valve and the working condition requirements. After receiving his drawing, our engineer confirmed that we can reach the accuracy of 0.3�¼m of this hydraulic relief valve and there may be no 3rd factory who can meet this requirement in Ningbo. If any doubt, we can make samples to test directly. Fred accepted AAK suggestion and paid a sample fee of $1,300.00. Two weeks later, AAK sent the samples of the hydraulic relief valve. After testing, Fred informed that AAK hydraulic relief valve was praised by the customer. Not only did the accuracy of the machined surface meet the standard, but the upper and lower deviation was also very small. While the samples of hydraulic relief valve from last two manufacturers are not stable, some with 0.3m, some with 0.4m, or even 0.6m. Only after comparison, the customer realized that AAK hydraulic relief valve is really high precision, so they have to admire it. The roughness accuracy of the machined surface within 0.3m is always the hard index of AAK. We have introduced the American HARDINGE precision CNC lathe, which gives us the most powerful support in terms of accuracy.
Yesterday morning, a colleague complained to me that he couldn't stand the Indian hydraulic valve customer. After communication, I learned that this old customer had to bargain every time when he placed the reorders, and he had asked for price reduction for 3 times. This time, this colleague couldn't bear it. There is an old Chinese saying that there is no need to bear it anymore. It seems to explain the legitimacy of the actions: I can't stand it. I have to do so. In fact, what you do when you can't bear it, whether it's right or wrong, good or bad, you shouldn't do it. What is the goal of AAK hydraulic valve? Isn't there more and more choice in the hydraulic valve industry? Specific to everyone of AAK hydraulic valve is to avoid making themselves have no choice. To be unbearable is to admit that you have fallen into a state of no choice. Think about my colleague carefully. Why didn't he have a choice? People often ask: is effort more important or choice more important? It is said that when you have a choice, choice is more important. If my colleague can insist on marketing like other colleagues and has more than 3 old customers of hydraulic valves, is there a better choice? And when you have no choice, hard work is important. In terms of specialty, adhere to the output of professional contents in hydraulic valve, and move towards the direction of technology and process; In terms of service, stick to the direction of trust. Combine the two, you don't need to worry about having no choice. In fact, there is another extension of this answer, that is, what is the purpose of efforts? Just to make yourself more selective. What is the AAK hydraulic valve effort for? In order to make ourselves have more choices to do a good job of hydraulic valves. AAK hydraulic valve adheres to the choice of subdivided target customers, and serves customers well with AAK hydraulic valve's distinctive advantages or distinctive technical features. AAK hydraulic valve adheres to a group of people, a lifetime and one thing, so that each user can make good use of AAK hydraulic valve. AAK hydraulic valve adheres to the principle of integrity, does a good job in the business of AAK hydraulic valve, and sincerely treats every customer who purchases hydraulic valves from AAK. Let more customers use good hydraulic valves with real materials without wasting money. I told my colleague that you should treat the client as your girlfriend. For example, she offered to break up with you today, and you gave her your last speech. If she understands your mind, she will come back. If she doesn't come back, it means she's not suitable for you. He sent an email to the Indian hydraulic valve customer: when you asked a price reduction of this hydraulic valve for the first time, and I gave you 5%. AAK treats the quotation of each hydraulic valve in good faith, and does not falsely quote the price, and does not arbitrarily quote the price, which is an
Erik compared more than 20 hydraulic pilot pressure control valve factories. No manufacturer can do the hydraulic pilot operated pressure control valves which can be used under high pressure above 450bar for more than one year. AAK hydraulic pilot operated pressure control valve passes the test at one time, and there is no abnormality after one year of use. Erik is from a German hydraulic equipment manufacturer. In the first half of last year, the company needed to purchase a special hydraulic pilot operated pressure control valve with a working pressure of more than 450 bar, a service life of more than one year and a durability of more than 2 million times. The boss realized that it was some difficult to purchase the hydraulic pilot operated pressure control valve this time, and asked Erik and his colleague to purchase at the same time. Whoever successfully purchased the hydraulic pilot operated pressure control valve first will be promoted and raised. Erik is full of energy and keeps looking for hydraulic pilot operated pressure control valve factories online and offline. He contacted more than 20 new suppliers, including AAK hydraulic valve. Most of the hydraulic pilot operated pressure control valve manufacturers replied that they need to be customized from the beginning of materials, and it takes 25 days to sample this special hydraulic pilot operated pressure control valve. Erik chose two factories to test the samples. A month later, Erik received the samples and asked the engineer to test them. The results failed, but the hydraulic pilot operated pressure control valve obtained by his colleague passed the first test, which made Erik very depressed. Fortunately, this is just in the test stage, the final effect depends on the test results of the hydraulic pilot operated pressure control valve one year later. Erik contacted AAK for the second time. He clearly informed that the samples of hydraulic pilot operated pressure control valves he selected in the first round failed. For the first time, he did not choose AAK because AAK needed 35 days. This time, he only asked AAK to make samples. Whether he can win or not, he can only count on AAK. Because the material selection and internal test of hydraulic pilot operated pressure control valves need time, Erik also understands the difficulties of making the samples. After 35 days, AAK sent 6 samples of hydraulic pilot operated pressure control valves. Last week, almost a year after the hydraulic pilot operated pressure control valve samples were sent, Erik sent an email to inform that AAK hydraulic pilot operated pressure control valve was the only sample that passed 2 million tests, and there was no abnormality after one year of use. Although his colleague's sample passed the early test, it could not withstand the high pressure above 450 bar for enough time, it leaked in less than a year.
Logan has been a purchaser of a hydraulic company in the United States for several years, and the purchasing of hydraulic valves in China is also very smooth. But recently, a high-precision hydraulic relief valve order worth more than $30,000 wasted him a lot of time. The original hydraulic relief valve manufacturer made the samples twice, but was still not approved by the customer. His customer understood that the original manufacturer was unable to meet the requirement of 0.3mm finish size allowance, and asked him to change the hydraulic relief valve manufacturer to make samples for the third time. If the hydraulic relief valve sample for the third time still cannot be approved, the customer can only cancel the order. This order attracted the attention of his boss, who asked him to solve the problem and get the sample of hydraulic relief valve approved at one time within 20 days. Five days later, Logan consulted many hydraulic relief valve suppliers, and most manufacturers said that they could not meet the standard of 0.3mm finishing size allowance. Logan is a little worried. He looks for hydraulic relief valve manufacturers everywhere on the Internet. He left a message on our AAK website: how can we guarantee the finishing dimension allowance? All such messages are basically for difficult problems encountered in the purchase of hydraulic valves. After some communication, it is understood that the Logan was stuck on the sample approval process of the hydraulic relief valve order, and he has contacted many hydraulic relief valve manufacturers, but no solution has been obtained. I suggested Logan try our sample directly, and let the test data to speak for itself and this also saves time. Logan doesn't seem to have a choice but to expect that maybe AAK hydraulic relief valve can pass the test. A week later, AAK sent out 3 hydraulic relief valve samples. Logan did not dare to send the samples to the customer directly after receiving them, so he had to find a third party for testing before sending them to the customer. Without incident, the customer approved AAK hydraulic relief valve samples. His boss was also surprised that how a hydraulic relief valve manufacturer found by Logan this time can solve the problem so quickly at one time. The heat treatment process in the early stage is the first step of finishing the size allowance. Most hydraulic relief valve manufacturers adopt local quenching, so the heat treatment process of the workpiece is not easy to control and may be deformed. As early as 6 years ago, AAK adjusted local quenching to overall quenching. At the same time, vertical flow treatment must be required for the hoisting mode in the process of quenching and tempering, so as to minimize the influence of tissue stress and thermal stress on deformation during workpiece heat treatment, so as to meet the requirements of dimensional allowance for finishing.
This Monday, Arthur sent an email to purchase 1,600 hydraulic threaded cartridge valves at one time, which was a little unexpected. Arthur came from a hydraulic equipment manufacturing company in Italy. He met with us at the PTC exhibition in Shanghai 3 years ago. At that time, he communicated with us for about half an hour. Then there were several inquiries for hydraulic threaded cartridge valves and several trial orders for hydraulic threaded cartridge valves. Last October, he suddenly sent an email saying that he had a client in Ningbo who wanted to visit AAK hydraulic valve factory. We introduced in detail a series of production links from raw material inspection and warehousing to rough machining, finishing, process inspection, assembly of valve body and spool, testing, packaging, warehousing, marking and shipping of each part of hydraulic threaded cartridge valve. After the visit, Arthur's client said they were satisfied with the scale, equipment and management of AAK factory and left. I wondered if this was really Arthur's client. More than a month later after visiting the factory, Arthur said that his company has developed a new hydraulic equipment, which requires high-precision hydraulic threaded cartridge valve. AAK needs to quote and make samples for testing as before. AAK sent 16 samples of hydraulic threaded cartridge valves after 30 days. I still think that this one will be the same as that one year ago, no big waves. I didn't understand that I made the mistake of "I thought" until receiving the large order of 1,600 hydraulic threaded cartridge valves yesterday. Today, I learned by email that it was not his client who came to visit the factory last year, but his assistant who often stayed in China. Before the company developed this hydraulic equipment, his assistant ran to more than 30 hydraulic valve manufacturers in China, especially for this special hydraulic threaded cartridge valve. AAK hydraulic valve has its own advantages in equipment and extension of equipment and on-site detail management. In particular, the component testing room of AAK is constant temperature and humidity for 24 hours, which is very helpful for hydraulic threaded cartridge valves with high precision requirements. Because of the particularity of this hydraulic threaded cartridge valve, the accuracy inspection of each component should be completed in a specific environment. Some quality problems of the products of many hydraulic valve manufacturers are just due to the deviation of the test results caused by the instability of the test environment. In the view of many factories, this may be a small detail, but AAK has done extremely rigorous testing. His assistant has not found a second one in Ningbo who pays so much attention to detail. That's why Arthur chose AAK to produce this big order of hydraulic threaded cartridge valve.
Duden is from Lukas hydraulic equipment company in Germany. We have cooperated for more than 2 years on hydraulic check valves and hydraulic throttle valves. The order volume is small each time, but the parameter requirements are very high. AAK never despised it because of the small order quantity of the hydraulic check valves or hydraulic throttle valves. At the end of last year, their company developed a new hydraulic unit. Due to time constraints, Duden purchased hydraulic check valves and hydraulic throttle valves from local hydraulic valve manufacturers in Germany. The technicians found the original design defects after installing the integrated valve into the equipment. The position of the hydraulic throttle valve next to the hydraulic check valve is high, accounting for a little position of the motor, which makes it difficult to install the motor. Lukas engineers are a little depressed. If the position of the hydraulic throttle valve is changed, the whole oil circuit layout needs to be changed, but the power supply of the hydraulic system will be affected after changing the oil circuit. What is more troublesome is that there is not much time to redesign and proofing. The Engineers asked Duden to contact some local hydraulic valve manufacturers to check if the design size of the hydraulic throttle valve could be slightly adjusted so that the motor could be installed. Duden checked with several local hydraulic valve manufacturers, all of them were not willing to make samples because of small quantity of the hydraulic throttle valves. Duden tried to purchase small-size hydraulic throttle valves from China to solve the installation problem of the motor. Some Chinese hydraulic valve manufacturers said that they could make samples according to the requested size of their hydraulic throttle valves, but the time needed was more than 30 days. Duden couldn't accept this time and was more worried about the quality of hydraulic throttle valves from these factories. Duden sent an email to AAK asking if we could make several samples of hydraulic throttle valves in 5 days. In the past, the sample time gave by Duden was usually flexible with more than 2 weeks. After asking, I learned that their designers are facing embarrassment. It is also too tight for us to make several hydraulic throttle valves in only 5 days. I suggest Duden give us the overall layout of the integrated valve block. Maybe our engineer has a solution. According to the hydraulic schematic diagram provided by Duden and the specific use of the hydraulic integrated valve block, AAK engineers analyzed it step by step. Finally, it was found that if the hydraulic throttle valve and the hydraulic check valve were designed in parallel, the functions of the two valves were combined to form a hydraulic throttle check valve, which was installed at the position of the hydraulic check valve, and the installation hole of the hydraulic
This morning, Robert sent an email asking about the production time of 1,200 hydraulic check valves, which surprised me a little, because in the past 2 years, he normally just placed small quantity trial orders of hydraulic check valves. Robert is a purchaser of John Finlay company in Australia. We met 2 years ago. A batch of hydraulic tamping machine equipment of their company began to receive complaints again and again from the previous year. After inspection, it was found that the hydraulic check valve in the equipment did not maintain pressure. Robert contacted the original hydraulic check valve manufacturer to find a solution. The manufacturer advised that the working pressure and working frequency of the hydraulic tamping machine may be too high, resulting in frequent collision between the ball valve and valve seat of the hydraulic check valve, affecting the sealing effect. The only solution is to replace the leaked hydraulic check valve. Although replacing the hydraulic check valve is a heavy workload, Robert has no choice but to accept. The trouble is that 6 months later, the same problem happened again. The customer was very unhappy. The boss asked Robert to find a new supplier of hydraulic check valve immediately. Robert suggested purchasing hydraulic check valves from AAK to replace those unqualified ones, because the durability test of AAK hydraulic check valves was the most lasting among all of the samples from different manufacturers at the beginning. At present, there is an equipment installed with AAK hydraulic check valve, which has been used for 1 year but without any abnormality. The boss thought that the price of AAK was more than 20% higher and unacceptable, and asked Robert to look for a new manufacturer of hydraulic check valves. In the process of continuous screening, Robert selected 5 hydraulic check valve manufacturers to try their samples. Basically, after half a year, these hydraulic check valve samples had similar problems one after another. Robert was at a loss. He once again suggested to the boss to purchase AAK hydraulic check valves. After comparing so many hydraulic check valve manufacturers, none of their samples can be used for more than 1 year under this working condition, but the equipment installed with AAK hydraulic check valve has been used for nearly 2 years, and there has been no failure to maintain pressure. If the hydraulic check valve needs to be replaced every 6 months, the after-sales cost is too high, which has far exceeded the 20% higher cost of the hydraulic check valves. More importantly, it brings the reputation of unstable equipment quality to users. After listening to Robert's analysis, the boss approved AAK as the preferred supplier of their company for hydraulic check valves. It took Robert 2 years to persuade his boss to place a large order with AAK. He knew that the durability of AAK hydraulic check valve
Last Friday, we received 3 emails from Niki, they are all the order for a same hydraulic check valve, but only the ship to address is different. It is the first time for their company to place the orders of 1,500 hydraulic check valves at one time. Niki is a purchaser of a Dutch hydraulic equipment company. Last year, a boarding bridge equipment needed hydraulic check valves. At that time, he planned to purchase from old suppliers. Unexpectedly, after dozens of hydraulic check valves from the initial samples were installed on the boarding bridge and tested for less than a month, the boarding bridge will slowly decline automatically. The engineer judged that the hydraulic system did not maintain the pressure, and it is likely that some hydraulic check valves leaked. However, after disassembling and inspecting the hydraulic check valves, it was found that the matching clearance accuracy of the valve spool and valve sleeve was within the normal range, and there was no jamming. Niki contacted the hydraulic check valve manufacturer, and manufacturer also didn't know why the hydraulic check valve leaked, so they could only replace those leaking hydraulic check valves. Niki is a little worried that if the leakage source of the hydraulic check valve is not found and replaced blindly, there may be a bigger problem later. Niki was not satisfied with the old supplier and had to start looking for new manufacturers of hydraulic check valves again. AAK received message from Niki on our website: what are the reasons for the leakage of hydraulic check valves? I realized that there was a leak in the hydraulic check valves purchased by Niki, but he hasn't found the root cause. After receiving the drawings of hydraulic check valve and the working conditions of boarding bridge equipment provided by Niki, we still can't 100% determine what caused the leakage of hydraulic check valve. We suggest him send us one of the previously leaked hydraulic check valves for analysis. After dismantling, our engineer is 90% sure to understand the root cause of the leakage, but still need to try sample to make it 100% sure. Niki is also willing to allow AAK to make samples according to his hydraulic check valve drawing. One month later, we sent 12 samples of hydraulic check valves to Niki and told him that the leakage of the hydraulic check valves from original manufacturer should be caused by poor details in production. There will be a certain gap between the cap and the thread of the valve sleeve of the hydraulic check valve. How to seal this gap is not only the detail but also the key, especially for the equipment with high working conditions. AAK uses thread anaerobic adhesive, which can completely fill the gap, enhance the sealing or retention force of mechanical connection components, prevent thread loosening and leakage due to vibration between the cap and valve sleeve of hydraulic check valves, and protect the joint from corrosion. Few hydraulic valve manufacturers
Cuenca is a senior purchaser of AGRIA company in Spain. The boss is very satisfied with his purchasing work. Two years ago, AGRIA company developed a hydraulic equipment, and there were complaints after sales for more than half a year. The main problem was that the starting force of the hydraulic system would be insufficient, which was caused by the increase of internal leakage of the hydraulic check valves in the equipment. After Cuenca contacted the original hydraulic check valve manufacturer, the manufacturer said that some hydraulic check valves may have deviation during assembly, and he was willing to replace the hydraulic check valves with large leakage with new ones. Cuenca thought it was completely solved after replacement, but what surprised him was that less than a year after the new hydraulic check valve was replaced, the same problem occurred again. The boss was very disappointed with his purchase of hydraulic check valves this time. The manufacturer of the original hydraulic check valves still said that except for replacing the hydraulic check valves, there is no other way. Cuenca began to worry that if the same problem happened a third time, it would be too shameless. To be safe, he began to look for a new supplier of hydraulic check valves and began to test samples. At the same time, he also wanted to know why the hydraulic check valves produced by the original manufacturer leaked. In this way, Cuenca contacted AAK hydraulic valve. After several rounds of communication with Cuenca, we learned the story between him and the original manufacturer of hydraulic check valves, and suggested him to send us the hydraulic check valves with problem and provide us the drawings of hydraulic check valves at the same time. AAK engineer disassembled the hydraulic check valves of the original manufacturer and found that there were wear marks on the sealing line on the surface of the poppet valve. When the pressure oil reversely enters the hydraulic check valve, the cone cannot strictly seal the oil and cause leakage, and some oil flows out of the oil inlet. After receiving AAK's analysis, Cuenca asked us to make 4 samples of hydraulic check valves according to his drawings. Our engineers designed a new hydraulic check valve according to the service frequency and working conditions of the equipment, replacing the cone valve with the ball valve. The cone valve is prone to fatigue creep deformation and wear after working for a long time, resulting in a gap between the valve sleeve and the cone, resulting in leakage. The outer circle of the ball valve can contact the inner taper ring line, and the connecting hole can be closed to reduce the leakage caused by wear. Cuenca was surprised that AAK dared to take the initiative to modify the drawings of their hydraulic check valves, and expected to see the sample performance of AAK hydraulic check valves. Two months later, AAK sent samples of the newly designed hydraulic check valves.
Andy is our old hydraulic valve customer in the The hydraulic cartridge valves he purchased from in previous years always has a standard of machining surface roughness around 0.8m. In last year, Andy sent an email to inform us that in the future, the machining surface accuracy of their hydraulic cartridge valves will be improved to within 0.3m. engineers believe that based on the current equipment system, it is very difficult to improve the machining surface accuracy of hydraulic cartridge valves to 0.3 m. It is also very difficult to find such a hydraulic cartridge valve manufacturer I know that has only two options, either give up the business of his hydraulic cartridge valves or accept his accuracy standard. This is the first time I have faced the choice of "standing in line" since I joined the hydraulic valve industry. The cooperation with Andy has always been trustworthy, pleasant and efficient. doesn't want to give up such customers. After two rounds of communication internally, technical team has not reached a consensus. I have to call my retired master and hope to hear his opinions. My master told me that this is a rare opportunity to catch up with and surpass the accuracy of international hydraulic cartridge valves. The roughness of the working surface under 0.3m is rare in , but some European hydraulic cartridge valve manufacturers have this strength. must first start with the equipment, and then select the most experienced operators from the factory for special aircraft training, so as to have the opportunity to compete with those top European hydraulic cartridge valve manufacturers. American HARDINGE precision CNC lathe is worthy of a try. At present, none of the domestic hydraulic cartridge valve manufacturers have this equipment. After contacting the equipment manufacturer, technical team took the hydraulic cartridge valves produced for Andy before to the equipment factory, and asked the engineer of the equipment manufacturer to go directly to the machine for proofing. A week later, we sent the hydraulic cartridge valve samples to Andy and asked them to test the accuracy parameters. Two weeks later, Andy informed that the previous hydraulic cartridge valve accuracy test was completed twice. This time, hydraulic cartridge valve was tested 4 times, and the accuracy fully met the standard. At the same time, he told me that after receiving the accuracy improvement notice, the other 3 domestic hydraulic cartridge valve manufacturers directly gave up, and only dared to test the sample and succeeded in one test. He was very surprised. The machine tool to be introduced by has advantages in accuracy. The parameters of the machine tool: spindle speed up to 6000r/ min, spindle radial run out 0.0008mm, positioning accuracy (X/Z)
AAK uses the DMG five axis machining center imported from Germany, which improves the stability and accuracy by 30%. Less than 5% of the hydraulic valve block manufacturers in the domestic industry are equipped with this set of equipment. After suffering losses elsewhere, an American customer went back to AAK after 45 days to place the order for hydraulic valve blocks. Last December, I received an inquiry from American customer Joshua about a hydraulic valve block. At that time, I was a little surprised to see the accuracy requirements of the hydraulic valve block. The accuracy was 5% higher than that of HydraForce series. This was not a small challenge, but I was still confident. The next day, I sent quotation to Joshua directly. Joshua then said that it was 12% higher compared with other hydraulic valve block manufacturers, he could not place an order with AAK. After 45 days, Joshua asked us whether the last quotation of hydraulic valve block was still valid. If the original price is maintained, he will place the order for the hydraulic valve block. For the sincerity of cooperation, Joshua also frankly told why he moved the hydraulic valve block order to AAK. The original hydraulic valve block manufacturer made samples for two times, and the parameters of each hydraulic valve block were not very stable. Some hydraulic valve block sample had very good accuracy, while others were very poor, which wasted 3 weeks of time. Joshua also checked with other manufacturers. All of them are not confident to achieve the accuracy that is 5% higher than that of HydraForce series. Another 2 weeks were wasted again. The customer was very angry that the order has been placed for 5 weeks, but the sample of the hydraulic valve block still could not be approved. Joshua felt that only AAK can make the sample successfully at one time. Even if it is 12% more expensive, it is acceptable. Aware of Joshua's dilemma, we specially spare a high-precision DMG five axis machining center lathe to arrange the proofing of this hydraulic valve block. A week later, AAK sent the hydraulic valve block samples. After 10 days, there was still no feedback from Joshua about the hydraulic valve block samples. We asked Joshua to know that he was also waiting nervously. Until Joshua's email last week, we know that his customer was very surprised that the accuracy of this hydraulic valve block sample not only exceeded 5% that of the HydraForce series, but the parameter stability of AAK hydraulic valve block was also more than 30% higher than that last time. Frankly, we were not surprised by this data, because more than one customer was surprised by the accuracy parameters of AAK hydraulic valve blocks. The reason why the accuracy of AAK hydraulic valve block exceeds 5% of HydraForce series is that it firstly benefits from the continuous updating of the equipment. When the vast majority of hydraulic valve block
Dimon is a new buyer of a hydraulic equipment manufacturing company in the United States. In the second half of last year, he purchased 100 hydraulic needle valves from an old supplier. After receiving the goods, the hydraulic needle valves were installed on the equipment. A few months later, some users complained that the pressure supply of some equipment was insufficient. Their technicians judged that the radial jamming of the valve spool of the hydraulic needle valve resulted in no flow regulation, which would lead to the failure of the power unit. The hydraulic needle valves need to be replaced with new ones as soon as possible to eliminate user complaints. His boss is not very satisfied that problem happened on even such a small number purchasing of hydraulic needle valves. Dimon is confused why the hydraulic needle valve supplier who had cooperated for 2 years would have such quality problems. He sent some problematic hydraulic needle valves back to the factory. The manufacturer replied that the accuracy of these hydraulic needle valves met the standard, but a small deviation in the size of the valve spool was caused by the deviation of the assembler. At that time, several valves were assembled at the same time in the assembly workshop, and a few deviations were difficult to avoid. Dimon realized that even the original manufacturer replaced the hydraulic needle valves with new ones, it still can not solve the problem of the radial jamming of the valve spool for 100%. He was afraid that if there were more user complaints, could he keep his job during the probation period? Dimon decided to find a new supplier of hydraulic needle valves. He left a message on our website: Can you solve the problem of radial jamming of the valve spool of hydraulic needle valve? At first, it was hard to answer this question. After several rounds of communication, we learned the story of his purchase of these 100 hydraulic needle valves. After reviewing the working conditions and drawings of hydraulic needle valve from Dimon, as well as the pictures of hydraulic needle valves from the original supplier, AAK suggested him trying samples directly. 20 days later, AAK sent 10 samples of hydraulic needle valves made per his requirements. Two months later, Dimon sent an email to us saying that he selected 5 factories from more than 20 hydraulic needle valve manufacturers to make samples. Only the samples from AAK and another factory did not have the problem of radial jamming of valve spool during the test. Their engineers suggested that AAK should be selected to replace the 100 hydraulic needle valves with potential quality problems, because the parameters of AAK hydraulic needle valve are the most stable. The boss knew that he dared to develop new suppliers and solved the hidden quality problems, although the probation period is not over yet, Dimon was approved to become a regular in advance. He told us this story privately.
Mathias, a Dutch hydraulic customer, urgently needed to purchase a batch of hydraulic valve blocks matching the German brand from China at the end of last year. He asked more than 10 old hydraulic valve block manufacturers. They all said that the accuracy of this hydraulic valve block was too high for their technology and equipment. Mathias had a hunch that nine times out of ten, the order for this hydraulic valve block would fail, because he knew that most hydraulic valve manufacturers just have CNC machine tools. But his owner attached great importance to this customer and asked him to implement the hydraulic valve block sample within 30 days. Within a week, Mathias consulted nearly 20 hydraulic valve block factories online and offline, almost all of them just have CNC lathes. Only two of them said that they have Japanese high-precision CNC machine tools. They can try to make samples but are not 100% sure. Two weeks later, Mathias tested the hydraulic valve block samples from 2 factories, and there was still a parameter error of 10% - 13%. Mathias suggested the factory re-make samples, and both factories surrendered. Time has been wasted for 3 weeks. It's only 2 weeks from the deadline required by the owner. Mathias is anxious and has no direction. While chatting with old friend Andy, Mathias revealed his dilemma. Andy is a veteran in the hydraulic valve industry and has cooperated with AAK hydraulic valve for 5 consecutive years. Andy told Mathias that the accuracy of this hydraulic valve block requires not only high-precision machine tools, but also old operators who understand the equipment. Most hydraulic valve block manufacturers are difficult to meet these two requirements at the same time. He suggested Mathias try AAK, who likes to overtime difficulties on high-precision hydraulic valves, and most operators have more than 5 years of experience in operating imported equipment. The subject of Mathias's first email to AAK hydraulic valve was that I was introduced by Andy. He said that the accuracy of this hydraulic valve block can only be produced in AAK. Opening his hydraulic valve block drawing, AAK engineers have 90% confidence. I replied to him directly that if it goes well, we can send the hydraulic valve block samples before the Chinese New Year holiday. Jan 28th is our last working day before CNY and the last day to send samples. Our team was great to send the samples on Jan 28th. When we came back from the Spring Festival holiday, we received an email from Mathias. Their technical team tested the accuracy of AAK hydraulic valve blocks. Each parameter met the accuracy required by the drawing, and almost every parameter was 30% higher than that of other hydraulic valve manufacturers. AAK is also the only hydraulic valve block manufacturer that can match the German brand among all the hydraulic valve manufacturers he contacted. He can finally make a
Henry is a purchaser of a hydraulic power unit manufacturer in the United States. He almost lost his job when he purchased the hydraulic pressure relief valves in the first time after just joining the company. AAK high-precision hydraulic pressure relief valves saved the job for him. Last October, one of their African customers customized a batch of hydraulic power unit equipment for use in African mining bases. The requirements of the equipment for the hydraulic pressure relief valves used are that there is no abnormality within 1 year. Henry contacted more than 10 hydraulic pressure relief valve manufacturers and screened 4 samples from each of 4 factories. A month later, the engineering department debugged these hydraulic pressure relief valves. Almost all hydraulic pressure relief valves from every factory have unstable hydraulic system pressure, but only the proportion is different. At first, the engineer thought it was due to the installation of hydraulic pressure relief valves or the problem of oil quality. After several commissioning, it was found that the outlet pressure of hydraulic pressure relief valves was almost equal to the inlet pressure. After disassembling the hydraulic pressure relief valves, it is found that the geometric tolerance is out of tolerance due to the accuracy of the main valve spool and valve hole. After knowing this, the boss thought that Henry had a problem on the communication with the hydraulic pressure relief valve manufacturers and asked him to solve the purchasing of the hydraulic pressure relief valves with the manufacturers within 4 weeks. Henry has made two rounds of screening for hydraulic pressure relief valve manufacturers and emphasized the working conditions, but still no one can achieve that every hydraulic pressure relief valve has no problem. He felt that he was cheated. The water in the hydraulic pressure relief valve industry was too deep. Henry found AAK hydraulic valve on Google and left a message on our website: Can AAK get the geometric tolerance of each hydraulic pressure relief valve consistent? After several rounds of e-mail communications, we learned about what happened when he purchased hydraulic pressure relief valves for the first time. We can only comfort him that he was misled by hydraulic pressure relief valve manufacturers due to lack of experience. He can test the samples of AAK hydraulic pressure relief valves. Three weeks later, AAK sent Henry 5 samples of hydraulic pressure relief valves. Their engineer tested each sample 3 times, and the hydraulic power unit equipment was normal. The boss praised his emergency ability. Now Henry doesn't have to worry about losing his job. We told Henry that according to the working conditions and drawings of this hydraulic pressure relief valve, the accuracy of each hydraulic pressure relief valve is required to meet the standard and be stable,
