Rubber Trimming Machine Introduction Frozen Shot Trimming an offshoot of cryogenic deflashing uses a system whereby parts are placed in a chamber, exposed to extremely cold temperatures (achieved with the use of liquid nitrogen) and then tumbled and blasted with a polycarbonate media. Because the burrs have a high surface area relative to their mass, they freeze very quickly and become brittle. The tumbling action combined with the impact of the media removes the burrs without damaging the part itself. Application Rubber NR NBR HNBR CR EPDM FKM ACM SILICONE Precision Plastic PA + GF PC + GF PPS POM PU PBT PTFE PEEK TPU TPE TPR Die - casting Alloy ZINC ALLOY MAG ALLOY Small and Round shape without sharp points will be more suitable for the Frozen Shot Trimming. SPECIFICATIONS NS - 60T Size: L1160mm * W1100mm * H2155mm Weight: 800kg Power Supply: AC380V 50HZ Electrical Capacity: 5KW * 3PH Design Temp: - 130Deg. C Design Pressure: 0.5 - 0.7 Mpa Outer Wall Material: SUS Frame Material: 100% SUS304 Barrel Capacity: 60L Wheel Speed: 7,200 rpm Max Barrel Speed: 0 - 26rpm Media Throw wheel Size : 250 Operation Mode: Touch Panel
Company Introduction Showtan Techno - Machine Nanjing Co. , Ltd. , the largest and most well - known manufacture of cryogenic deflashing machine in China, is a subsidiary company of a well - known Japanese cryogenic deflashing machine and gas products manufacture - Showa Denko Gas Products Co. , Ltd. , which is a member of the world famous multinational and comprehensive group - Showa Denko Group from Japan. Automatic Deburring Machine Introduction Automatic deburring is a process for removing flash from molded rubber parts. We use liquid nitrogen, high - speed rotation and shot blasted plastic media in varying combinations to remove the flash in a highly precise, economical and expedient manner. Parts that have thin flash can be quickly and thoroughly cryogenically deflashed. This process is exceptionally good at removing the inner dimensional and complex flash that cannot be removed by any other method. Application O - rings, gaskets and other rubber sealings Insulators and other electric / electronic components Valve stems, washers and fittings Short tubes and flexible boots Rubber absorbers and bumpers for automobile Face masks & goggles Mobile phone housing and intelligent watch strap Zinc and mag alloys like door lockers for auto cars SPECIFICATIONS NS - 60T Size: L1160mm * W1100mm * H2155mm Weight: 800kg Power Supply: AC380V 50HZ Electrical Capacity: 5KW * 3PH Design Temp: - 130Deg. C Design Pressure: 0.5 - 0.7 Mpa Outer Wall Material: SUS Frame Material: 100% SUS304 Barrel Capacity: 60L Wheel Speed: 7,200 rpm Max Barrel Speed: 0 - 26rpm Media Throw wheel Size : 250 Operation Mode: Touch Panel
Rubber and plastic machinery.
Cold Shot Nitrogen Deburring Machine Introduction Automatic deburring is a process for removing flash from molded rubber parts. We use liquid nitrogen, high - speed rotation and shot blasted plastic media in varying combinations to remove the flash in a highly precise, economical and expedient manner. Parts that have thin flash can be quickly and thoroughly cryogenically deflashed. This process is exceptionally good at removing the inner dimensional and complex flash that cannot be removed by any other method. Application O - rings, gaskets and other rubber sealings Insulators and other electric / electronic components Valve stems, washers and fittings Short tubes and flexible boots Rubber absorbers and bumpers for automobile Face masks & goggles Mobile phone housing and intelligent watch strap Zinc and mag alloys like door lockers for auto cars SPECIFICATIONS NS - 120C Size: L1400mm * W1300mm * H2300mm Weight: 1500kg Power Supply: AC380V 50HZ Electrical Capacity: 8KW * 3PH Design Temp: - 130Deg. C Design Pressure: 0.5 - 0.7 Mpa Outer Wall Material: SUS Frame Material: 100% SUS304 Barrel Capacity: 120L Wheel Speed: 6, 000 rpm Max Barrel Speed: 0 - 16rpm Media Throw wheel Size : 350 Operation Mode: Press Button
Cold Shot Nitrogen Deburring Machine Introduction Automatic deburring is a process for removing flash from molded rubber parts. We use liquid nitrogen, high - speed rotation and shot blasted plastic media in varying combinations to remove the flash in a highly precise, economical and expedient manner. Parts that have thin flash can be quickly and thoroughly cryogenically deflashed. This process is exceptionally good at removing the inner dimensional and complex flash that cannot be removed by any other method. Application O - rings, gaskets and other rubber sealings Insulators and other electric / electronic components Valve stems, washers and fittings Short tubes and flexible boots Rubber absorbers and bumpers for automobile Face masks & goggles Mobile phone housing and intelligent watch strap Zinc and mag alloys like door lockers for auto cars SPECIFICATIONS NS - 120C Size: L1400mm * W1300mm * H2300mm Weight: 1500kg Power Supply: AC380V 50HZ Electrical Capacity: 8KW * 3PH Design Temp: - 130Deg. C Design Pressure: 0.5 - 0.7 Mpa Outer Wall Material: SUS Frame Material: 100% SUS304 Barrel Capacity: 120L Wheel Speed: 6, 000 rpm Max Barrel Speed: 0 - 16rpm Media Throw wheel Size : 350 Operation Mode: Press Button
