Pass box adopts the sand light stainless steel inside,which is flat,neat,wearable.The surface material of pass box is cold rolled steel or stainless steel. Doors in two sides with machinery or electronic interlock device makes two doors can¬H be in the open state at the same time,it prevent the cross-infection between clean zone and unclean area. OEM is available.
Characteristic 1.Clean bench (level) is adopted the super thin air filter without clapboard to minimize the size of structure. The clean bench is matched stainless steel table-board and glass on sides. 2.It makes the workaround roomy and bright. We adopt send-off wind system that the air velocity is adjustable by touch the switch lightly,which makes the wind speed perfect. 3. The prefilter that with big wind speed is convenient to take town. It is not only protect the HEPA filter's life and also ensure the wind velocity. 4.Level air current,opened desk type,and convenient operation. 5. Customized design is available. standard export packing
Laminar air flow information We have CE,ROHS,ISO9001,ISO14001 for it. KLC series mini-type air flow laminar box, It is used for the partical high clean requirement in workshop and lab. Characteristic 1).It is adopted the super thin air filter without clapboard to minimize the size of structure. The air flow laminar box is matched stainless steel table-board and glass on sides. 2). It makes the workaround roomy and bright. We adopt send-off wind system that the air velocity is adjustable by touch the switch lightly,which makes the wind speed perfect. 3).The pre - filter that with big wind speed is convenient to take town. It is not only protect the HEPA filter ' s life and also ensure the wind velocity. 4).Level air current, opened desk type, and convenient operation. 5) Customized design is available for laminar air flow. Packing is plywood.
Our products have high quality with competitive price.We provide free samples.All standard vials usually can be despatched within 24 hours after receipt of payment. 12 packs in one ccarton(365*195*122mm) ,48 packs in one carton(420*370*270mm) ;Weight is 15.6KG per carton . All the caps with septa fit for 2ml vials are packed by Food Class PP bag in the 10000 class cleaning Room ;100pcs per pack ,100packs in one carton;Weight is 5kg per carton .
Our products have high quality with competitive price.We provide free samples.All standard vials usually can be despatched within 24 hours after receipt of payment. 12 packs in one ccarton(365*195*122mm) ,48 packs in one carton(420*370*270mm) ;Weight is 15.6KG per carton . All the caps with septa fit for 2ml vials are packed by Food Class PP bag in the 10000 class cleaning Room ;100pcs per pack ,100packs in one carton;Weight is 5kg per carton .
Our products have high quality with competitive price.We provide free samples.All standard vials usually can be despatched within 24 hours after receipt of payment. 12 packs in one ccarton(365*195*122mm) ,48 packs in one carton(420*370*270mm) ;Weight is 15.6KG per carton . All the caps with septa fit for 2ml vials are packed by Food Class PP bag in the 10000 class cleaning Room ;100pcs per pack ,100packs in one carton;Weight is 5kg per carton .
Our products have high quality with competitive price.We provide free samples.All standard vials usually can be despatched within 24 hours after receipt of payment. 12 packs in one ccarton(365*195*122mm) ,48 packs in one carton(420*370*270mm) ;Weight is 15.6KG per carton . All the caps with septa fit for 2ml vials are packed by Food Class PP bag in the 10000 class cleaning Room ;100pcs per pack ,100packs in one carton;Weight is 5kg per carton .
Specification: 12/13 X 75mm, 12/13 X 100mm, 15/16 X 100mm Additive: No additive Blood Volume (ml): 3, 4, 5, 6,7, 9, 10 Packing: (1). For 12/13 X 75mm, 12/13 X 100mm: 1200 PCS per carton (2). For15/16 X 100mm: 600 PCS per carton Description: It used for blood collection and storage for biochemistry, immunology and serology tests in labs/hospitals. Strict tube washing technology and stopper treated with anti-precipitation film make the tube usable for trace element test. Tube inner wall treated specially possesses a good biocompatibility with blood, avoiding effectively hemolysis and blood sticking to the tube. This tube can provide enough and nonpolluted serum specimen for clinical test, while keeping the serum invariable in a long test period. 1200PCS per Carton
1. Forced air drying oven 2. Lcd screen 45l capcity 4. 10~300 degree 5. Ce certificate Packing size:590¡¨¢560¡¨¢790mm Standard export carton
Brief introduction: Lt-01 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-01 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-01 leakage tester complies with astm d3078 and gb/t 15171 standards. The leak detection system is composed of the mainframe and the vacuum chamber. A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated. Features Lt-01 leak tester uses vacuum ejector to generate stable vacuum environment. . The leak detection requires no electricity High leakage test efficiency Extra-thick perspex Different chamber sizes available No calibration needed No vacuum pump required Easy installation, start-up and operation Low maintenance Astm d3078 , gb/t 15171
Brief introduction: Lt-02 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-02 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-03 leakage tester complies with astm d3078 and gb/t 15171 standards. The leak detection system is composed of the mainframe and the vacuum chamber. A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated. Features Astm d3078 gb/t 15171
Brief introduction: Lt-03 leak tester is designed for the examination of airproof property of packages, containers, bags, pipes. Lt-03 package air proof tester is widely used in food, beverage, pharmaceutical, daily chemical, electrical and electronic industries, etc. Lt-03 leakage tester complies with astm d3078 and gb/t 15171 standards. The leak detection system is composed of the mainframe and the vacuum chamber. A test sample is placed into a vacuum chamber with water and the air above water level is evacuated by a venturi vacuum ejector. A great pressure difference is created inside and outside the sample and any slight leakage can be observed and identified when the sample is inflated. Features Lt-03 leak tester uses vacuum ejector to generate stable vacuum environment. The state-of-the-art human-computer interface and plc control unit on the leakage detection system make the parameter setting and test operation direct and easy. By saving different groups of parameters, users are free from the troubles of setting parameters each time before use. At the same time, different testing results and total test numbers can be saved to avoid any human errors. 1. Leak test process all automatic 2. Touching screen operation 3. Digital vacuum degree and test time input 4. Parameters and test data automatic saving 5. Automatic vacuum maintenance and air back-flushing 6. Extra-thick perspex 7. Different chamber sizes available 8. No vacuum pump required 9. Easy operation and maintenance Astm d3078 , gb/t 15171
Application and Brief Intro LSST-01 Leak and Seal Strength Tester is suitable for the quantitative determination of sealing strength, heating sealing quality, burst pressure and leakage of flexible and aseptic packages. The Leak and Seal Strength Detector can also be used to determine the sealing performance of pilfer-free bottle caps and soft tubes. The compression strength, connection strength of cap and body, cap losing strength, seal strength and butting strength of tubes are the applications of LSST-01 Seal Strength Testing System. This Seal Strength Testing System conforms to standards of ISO 11607-1, ISO 11607-2, ASTM F1140, ASTM F2054, GB/T 10440, GB 18454, GB 19741, GB 17447, GB/T 17876, GB/T 10004, BB/T 0025, QB/T 1871, YBB 00252005, YBB 00162002 . Principle The three test modes of the positive pressure method, which LSST-01 Leak and Seal Strength Tester satisfies are as follows: A. Burst Test: LSST-01 Leak and Seal Strength Tester internally pressurizes the packages until the package fails. The test pressure is the maximum pressure detected before the package fails. B. Creep Test: Pressurize the package internally to a specific pressure and maintains this pressure for a specific time. The test measure is pass/fail. C. Creep to Failure: The package is creep-tested and held until the package fails. The pressure setting is higher than that of the creep test to ensure the package fails in some time. The measure is the time until failure.
Application and Brief Intro HST-01 Heat Seal Tester is for the determination of the heatsealability of a surface, or sealant layer of films, laminates, composites and polymers etc. How well the material heatseals is expressed quantitatively as seal strength as a function of the sealing conditions of temperature, time and pressure. HST-01 Heat Seal Tester is professionally designed for the precise measurement of the three parameters of temperature, time and pressure in the heat seal process. HST-01 Heatsealability Tester conforms to standards of ASTM F2029, QB/T 2358 and YBB 00122003. Principle Place a sample between two-heated sealing jaws of HST-01 Heat Seal Tester with flat surfaces when the required temperature reaches equilibrium. The upper seal jaw, driven by a gas cylinder, is pushed down, to exert a certain pressure on the sample and remain for some time. When the preset sealing time ends, the upper sealing jaw returns to its original position and the whole heatsealability testing process finishes. ASTM F2029, QB/T 2358, YBB 00122003
1 Frame Steel structure 2Table topMade of 12.7mm thick corrosion-resistant black c-spc , one door one drawer 3 Cabinet Use high quality cold-rolled steel sheet, the surface is parkerised by acid and electrostatic sprayed by epoxy resin powder. Color can be chosen according to color-disc 4 Slideway Three section slide rail , no noise 5 Hinges Pen type high quality hinges 6Handle Stainless steel bright type handle Advantages: Steel structure lab furniture are elegant-looking , color-rich, economy and durability and so on. Our products have various sizes and styles giving you a modern lab space. Our products have passed the iso9001 Our price will be satisfactory and our quality will be the same as or even beyond your request. We will design the customized products for you. Product pictures for reference:
1. Fully automated, discrete, random access . 10. Perfect function of quality control management is convenient for users to manage the clinical test result. 11. Detecting in the whole reaction process with reaction curve, convenient for users to monitor thoroughly and scientifically analyze the detection data. 12. Supporting software can implement the function of detecting surplus reagent through liquid level induction of reagent probe. 1150*980*1350
Steel structure; cabinet with 1.2mm cold-rolled steel plate bending, stamping, surface after degreasing, pickling, phosphorus into anti rust treatment, thenelectrostatic powder spraying epoxy protective layer of acid and alkali corrosion resistant surface treatment, surface using 12.7mm solid physiochemical board panel, the circumference edge grinding processing, corrosion resistant, acid and alkali resistance, resistance, wear-resistant, anti static, antibacterial, flame retardant, particularly suitable for chemical, physical, biochemical, clinical room table. Holding a special mould laboratorymolded pvc handle, accord with human body engineeringstandards; hinge adopts 304# stainless steel; guide rail adopts 16 inch wide plate three section type ball mute slide, surface galvanized processing; professional moldcomposite structure; adjustable screw is m12*50mm, the outer cover for an injection molding die, Wood packing
Product feature: 1.Professional design, aesthetic modeling 2.Multi-layer insulation design of high vacuum for reducing evaporation loss rate of liquid nitrogen and using cost to the lowest degree 3.Aluminum alloy materials of high strength for extending service life to more than five years 4.Unique support structure for long-distance transportation 5.A locked-cover switch for safety of preserved sample is optional 6.A protective casing for preventing collision and offering convenience is optional 7.A handcart for enhancing mobility is optional Main uses : 1. Vital preservation of animal semen 2. Vital preservation of biological sample 3. Cryogenic treatment of metal material 4. Cryogenic assembly of precision parts 5.Cold storage and freezing in medical health and refrigeration in operation. 34cm*34cm*59cm, 8.5kg
Overview: Self-pressurized liquid nitrogen tank produces pressure by evaporation of little liquid nitrogen so that liquid nitrogen will exhaust itself and complement other containers. It finds its application in the transportation and storage of liquid medium (liquid nitrogen, liquid oxygen and liquid argon) and cold source of other refrigeration equipments. It is now widely used in tool and die industry, animal husbandry, medicien, semi-conductor, food, cryogenic chemical industry, aerospace, military and other industries and areas. (dewar flask, dewars, dewar, etc) Production materials: Inner and outer cylinders of the main body are made up of 304 austenite cryogenic special stainless steel of fine quality; absorbers are regenerated and activated; multi-layer insulation materials are oil-and-lipid-free thin imported composite. Production technology: All weld joints are tested by helium mass spectrometer; 100% of products have gone through strict cryogenic examination; unique patented vacuum-pumping technology ensures extremely evaporation loss rate; optional machine or digital display liquid level gauge; container shell makes use of unique polishing technology and has aesthetic modeling; the entire production process strictly follows is9001:2008 standards. Security technology: A two-way multi-layer security system is installed to ensure safety for production use; layout of the safety valve, outlet valve, vent valve, and booster valve is reasonable for secure and convenient operation. 70cm*70cm*140cm, 115kg
Monitoring management system for liquid nitrogen biological container of cord blood stem cell bank is a system integration product that was studied and developed for five years by our company. By drawing advanced management experience of cord blood stem cell bank at home and abroad, our company uses creatively advanced data collection technology, communication technology, automatic control technology, and embedded software technology. The system is mainly made up of remote terminal unit (rtu) of intelligent monitoring of biological container and data service center (dsc). Intelligent monitoring terminal unit has the following functions: real-time collection of temperature of low and high position, real-time monitoring of liquid height, calculation of liquid nitrogen loss, automatic switch of liquid inlet electromagnetic valve according to liquid level and temperature, internal local area network is used to connect tank body computer with server of monitoring center, dtu sends warning message to the cell phone of watch keeper including low-and-high-position overheating warning and sensor failure warning, powerful mis management system for objects in cryopreservation, and so on. Data monitoring center analyzes and stores data provided by rtu and these data are investigated by management staff. Monitoring terminal unit can check conveniently the state of every network monitoring terminal by connection of local area network and monitoring center on a computer in the monitoring center without reaching any biological storage container. Monitoring center computer is also in charge of storing and managing all objects stored or to be stored in the liquid nitrogen tank. Monitoring center software is mainly made up of eight major modules including operation model selection, data monitoring, alarming, and object information management.
