Description The Trusted Field Termination Assembly (FTA) 24V dc Digital Input T8800 is designed to act as the main interface between a field device generating a digital signal and the Trusted TMR 24V dc Digital Input Module T8403. Features 40 input channels per FTA. Industry standard field device connections (2-wire). Standard DIN rail compatibility. Simple installation and connection. 24V dc operation. SmartSlot connection for one to many hot replacement of input modules. Fused field power supply per channel. On-board LED indication field power supply integrity.
General Information Product ID: 3BSE023675R1 Medium Description: AI845 Analog Input Module, 8 channels, Redundant or single, HART. Product Type: I/O Module Country of Origin: India Customs Tariff Number: 85389091 Length: 102 mm Height: 119 mm Width: 45 mm Weight: 0.34 kg
Description The Trusted TMR 24V dc digital output module interfaces to 40 field output devices. Outputs are arranged in five groups of eight outputs. All outputs in a group share a common power source and return. Fault tolerance is achieved through Triple Modular Redundancy (TMR) within the same module for each of the 40 output channels. The module provides on-board sequence of events (SOE) reporting with a resolution of 1ms. The event is the actual sensing of the field device loop current. Each triplicated section (slice) of the module, receives output data from the Trusted TMR processor and sends its data to an internal safety layer hardware voter. Each slice uses the voted data to control the outputs. Every output channel consists of a six-element voted array. The output switch array provides fault tolerant, uninterrupted control under an output switch failure condition. Output switching and fault diagnostics comply with the demanding requirements of IEC-61508 SIL-3 for First fault - Fault tolerant, and Second fault Fail-safe outputs. When a module fault is detected, the Trusted TMR processor will flag the unhealthy condition, indicating the need to replace the module. Control continues until a replacement (healthy) module is available. Replacement modules can be located in a standby slot next to the module or in a designated SmartSlot with a temporary connection to the same Trusted termination assembly. Each output is user configurable to perform line monitoring of the connected field devices to detect field wiring and load failures. Automatic over-current protection is inherent in every output circuit which eliminates the need for fuses. Modules may be placed in any I/O module slot in a Trusted processor chassis or expander chassis. Once the I/O module configuration is set, mechanical keying is available on all I/O modules to prevent inserting a module into an incorrect slot. Configuration of the module is carried out using the Trusted Toolset running on an engineering workstation. Once configured and loaded into the Trusted controller, replacement modules are online educated by the TMR processor. Features 40 TMR output channels per module. Five isolated groups of eight outputs each. Six-element voted output array. Comprehensive diagnostics and self-test. Guaranteed, First fault fault tolerant, Second fault fail-safe. Line monitoring on a per channel basis. Automatic over-current protection no fuses required. 2500V dc optically isolation. Hot replaceable. Front panel status LEDs for each channel. Module fault and status indicators. IEC 61508, SIL 3 safety applications. On-board 1 ms resolution sequence of events reporting.
Description The Trusted TMR 24 / 48V dc Digital Output module interfaces to 40 field devices. Triplicated diagnostic tests are performed throughout the module including measurements for current, and voltage on each portion of the voted output channel. Tests are also performed for stuck on and stuck off failures. Fault tolerance is achieved through a Triple Modular Redundant (TMR) architecture within the module for each of the 40 output channels. Automatic line-monitoring of the field device is provided. This feature enables the module to detect both open and short circuit failures in field wiring and load devices. The module provides on-board Sequence of Events (SOE) reporting with a resolution of 1ms. An output change of state triggers an SOE entry. Output states are automatically determined by voltage and current measurements on board the module. Features 40 Triple Modular Redundant (TMR) output channels per module. Comprehensive, automatic diagnostics and self-test. Automatic line monitoring per channel to detect open circuit and short circuit field wiring and load faults. 2500V dc optical isolation barrier. Automatic over-current protection (per channel), no fuses required. On-board Sequence of Events (SOE) reporting with 1ms resolution. Module can be hot-replaced on-line using dedicated Companion (adjacent) Slot or SmartSlot (one spare slot for many modules) configurations. Front panel output status LEDs for each channel indicate output status and field wiring faults. Front panel module status LEDs indicate module health and operational mode (Active, Standby, Educated) TUV Certified IEC 61508 SIL 3 Outputs are powered in isolated groups of eight. Each power group can be of a different voltage
Description The Trusted TMR analogue input module interfaces to 40 single-ended field input devices. A wide input range and programmable thresholds allow the module to be used in most voltage or current configurations. Comprehensive diagnostic tests are performed on each input channel, including tests for out of range values and stuck at failures. Fault tolerance is achieved through Triple Modular Redundancy (TMR) within the same module for each of the 40 input channels. The module can apply a digital filter to each input channel. Individual channels can be configured for high noise immunity (50Hz or 60Hz rejection), low noise immunity (fast response) or pass-through operation (no filtering). Each input channel has four configurable state thresholds, which may be assigned to SOE reporting. A change of state triggers an SOE entry. The on-board sequence of events (SOE) reporting has a resolution of 1ms. Each triplicated section of the module, referred to as a slice, conditions and measures each channel independently. Each slice is optically isolated up to 2500V dc. Each slice sends its data to a safety layer hardware voter that presents the information from all three slices to the Trusted TMR processor. When a fault is detected on a slice of the module, the Trusted TMR processor will flag the error, indicating the need to replace the module. The Trusted TMR processor will continue to use the information provided by the remaining two slices until a replacement module is available. Replacement modules can be located in a standby slot next to the module or in a designated SmartSlot with a temporary connection to the same Trusted termination assembly. Modules may be placed in any I/O module slot in a Trusted processor chassis or expander chassis. Once the I/O module configuration is set, mechanical keying is available on all I/O modules to prevent inserting a module into an incorrect slot. Configuration of the module is carried out using the Trusted Toolset running on an engineering workstation. Once configured and loaded into the Trusted controller, replacement modules are online educated by the TMR processor. Features 40 TMR input channels per module. Comprehensive diagnostics and self-test. 2500V dc optically isolation. Digital signal filtering on a per channel basis. Four user configurable thresholds per channel. On-board 1ms resolution sequence of events reporting. Hot replaceable. Front panel status LEDs for each channel. Module fault and status indicators. IEC 61508, SIL 3 safety applications.
Description The Trusted 40 Channel Analogue Input FTA T8830 is designed to act as the main interface between a field device generating an analogue signal and the Trusted TMR Analogue Input Module T8431. Features 40 input channels per FTA. Industry standard field device connections (2-wire). Standard DIN rail compatibility. Simple installation and connection. 24V dc operation. SmartSlot connection for one to many hot replacement of input modules. Fused field power supply per channel. On-board LED indication field power supply integrity.
General Information Product ID: 3BSE051306R1 Medium Description: AI835A Analog input Module, 8 channels, thermocouple/mV Technical Information: Supersedes 3BSE008520R1/3BSE008520Z1/ 3BSE051306Z1 Product Type: I/O Module Country of Origin: Estonia Customs Tariff Number: 85389091 Length: 150 mm Height: 150 mm Width: 75 mm Weight: 0.2 kg
General Information Product ID: 3BSE028925R1 Medium Description: AI843 Analog Input Module, 8 channels, Redundant or Single, thermocouple /mV Product Type: I/O Module Country of Origin: Estonia Customs Tariff Number: 85389091 Length: 102 mm Height: 119 mm Width: 45 mm Weight: 0.25 kg
General Information Product ID: 3BSE052605R1 Medium Description: AO815 Analog Output Module, 8 channels with HART Product Type: I/O Module Country of Origin: India Customs Tariff Number: 85389091 Length: 102 mm Height: 119 mm Width: 45 mm Weight: 0.3 kg
PU Squeegees electronic printing squeegees Material: polyurethane Hardness: 55 A, 60, 65, 70, 75, 80, 85, 90, 95 SHORE A polyurethane Squeegees Thickness: 2 - 20mm Profile: straight square edge, single bevel, double bevel High precise LCD printing squeegees Length: 4000mm Color: red, green, natural, blue, white Width: 9mm - 500mm Size: 50*9mm, 55*9mm, 45*9mm, 50*7mm, 45*7mm, 40*7mm, 55*5mm, 50*5mm, 45*5mm, 40*5mm, 35*5mm, 25*5mm. Feature: a. High resistance b.Excellent resistance and minimum swell c.Ultra high durability-longer lifespan d.Precisely finished edges e.Super solvent resistance It is widely used in textile screen printing, high precise LCD, electronic printing, large advertisement, auto-printing machine, high precise multi-layered circuit board ect. High precise LCD printing squeegees and polyurethane squeegees are our main product. Our product are widely used in textile screen printing, high precise LCD, electronic printing and so on. More information you can view here
PTC thermistors current protector, also called PTC thermistor resettable fuses, protect load against over-current, overload, short circuit. No need for replacement, resume protective function after a short cooling-down time. Ceramic PTC (positive temperature coefficient) thermistors are used instead of conventional fuses to protect load, such as motors, transformers, or electronic circuit, against overcurrent for circuit protection. PTC thermistor protector not only respond to inadmissibly high currents but also if a preset temperature limit is exceeded. PTC thermistor over-current protector limits the power dissipation of the whole circuit by increasing their resistance and thus reducing the current to a harmless residual value. In contrast to conventional fuses, PTC thermistor resettable fuses do not have to be replaced after elimination of the fault but resume their protective function immediately after a short cooling-down time. PTC Thermistor Over-current Protector Application It applies in the over-current overload and short circuit protection of transformers, battery charger, switches, switch power supply, adaptor, meter, instrumentation, apparatus, electronic coils, control panels, air conditioner, automotive electron, etc. Operating Principle of PTC Thermistor for Overload Over-current Protection The operating principle is as indicated in the following. When a circuit is in the normal status, the current through PTC is lower than the rated current and PTC thermistor protector is in the normal state with small resistance value, which will not affect the normal operation of the protected circuit. In case of some fault in the circuit and the current is greater than the rated current, the PTC thermistor protector will become hot quickly and present a high resistance state, which sets the circuit relatively "off" to protect the circuit from damage. After the fault is removed, PTC thermistor protector will automatically restore its low resistance state and the circuit will resume normal operation. Normally, when PTC thermistor is used as an overcurrent protection component, it is preferred to select maximum operating current, maximum operating voltage and proper specifications. Furthermore such factors should be taken into consideration as the dimensions of the components, rated zero-power resistance, operating temperature range, etc.
Thermal Gap Pad, thermal pad, thermal gap filler GLPOLY thermal pad is featuring a high thermal conductivity of 6.0W/mK, its higher than that of most of competitor. Comparing with Bergquist gap pad 5000S35, the data will shows that GLPOLY thermal gap filler pad can perfectly replace the BQ 5000S35. Firstly, the thermal conductivity of GLPOLY thermal gap filler pad is higher that that of BQ 5000S35; the thermal resistance is only 0.16in2/W, its just one third of BQ 5000S35. Comparison data reflects that GLPOLY thermal gap filler pad offers more excellent thermal performance than BQ5000S35. For the electrical property, the dielectric breakdown voltage is 16KV, its 3 times greater than BQ 5000S35s. this will ensure the stability of performance of devices. The material yields extremely soft characteristics while maintaining elasticity and conformability. Conforms to demanding contours and maintains structural integrity with little or no stress applied to fragile components. The inherent natural tack on both sides assists in application and allows the products to effectively fill gaps, reducing thermal resistance and enhancing the overall thermal performance. GLPOLY thermal gap filler pad is ideal for high-performance application at low stress or pressure. Features Ultra conformability Designed for low-stress applications Fiberglass reinforced for puncture, shear and tear resistance ThicknessMm---- 0.3~5.0 Densityg/cm3---- 2.6 ,HardnessShore 00--20,20 Thermal Conductivity W/m*K--2.0,2.8
Pellets Φ1-3mm 99.999% Φ2-4mm
Overview Quick Details Place of Origin: Shanghai, China Brand Name: Longjoin Type: Custom Dimming Max. Load Power: 1.2VA Voltage: 110-277VAC Product name: photo electric light control Application: Street Lighting,Garden Lighting,Landscape Lighting etc Photocell controller Schematic: photodiode sensor Output: 0-10V Dimming / optional Logo: Customized logo,>500 Cover material: PC Power Consumption: 1.2VA On-Off Levels: 50 lux HS CODE: 85365000 We are factroy: Factory in Shanghai city.Best products for you. Supply Ability Supply Ability: 50000 Piece/Pieces per Month Packaging & Delivery Packaging Details Each piece in one small white paper box, 100 boxes in one master carton. Port Shanghai/Ningbo/Any port of China
Model Number:JH-051 Product name: Special steel fixing system for heating Brand Name:Jinhan standard:GB Application:broad Material: carbon steel produce according to customers'drawing and requirement samples available
6FC5370-0AA00-1AA1 6FC5370-0AA00-1AA1 ZhongHaiDe (Fujian) Industrial Equipment Co., Ltd., which is a well-developed equipment supplier in the field of automation in China currently. Our company has been established for 4 years, located in a rapidly developing coastal city named Fuzhou. Our business scope can be divided into 6 parts. Large DCS system modules. Large imported industrial robot spare parts. Inverters, soft start equipment and emergency power supply. Automated industry(PLC, DDC, DCS), monitors(FMCS, FCS, BAS), PLC spare parts and HMI. Large servo motor drivers. The electromagnetic valves, cylinders, flow meter, sensors, safety barriers and thermostats. Our products are mainly from the leading companies in the field of automation from United States, German, Japan and other developed countries that makes our products convictive and trustworthy, such as ABB, Foxboro, Yaskawa, Sew and so on. For example, in the supply of Robot spare parts, our main supplier is ABB company from Switzerland, who is the world's leading supplier of industrial robots, with various types of robots, such as small, large, spray and special robots, and has installed more than 250,000 robots worldwide. We have build long-term and stable cooperation with these companies dedicating to supply high-quality products to our customers. If you have interested in our products, you can contact the email also you can add wechat We are looking forward your reply. . to get more information. 6FC5253-5AX00-3AF0 6FC5303-0AF30-1AA0 6FC5303-0DM13-1AA1 6FC5312-0DA01-0AA0 6FC5313-5AG00-0AA3 6FC5370-0AA00-3AA1 6FC5370-0AA00-3BA1 6FC5370-0AA00-3CA1 6FC5370-0AA00-1AA1 6FC5370-0AA00-2AA1 6FC5370-0AA00-2BA1 6FC5551-3AA00-1BB0 6FC5551-3GA00-0BB0 6FC5551-4AA00-3BB0 6FC5571-0AA01-0BF0 6FC5551-0AB00-0BB0 6FC5551-0GA00-0BB0 6FC5551-1AB00-0BB0 6FC5551-2AA00-3BB0 6FC5551-2AB00-1BB0 6FC5551-2GA00-3BB0 6FC5551-3AA00-0BB0 6FC5603-0AD00-0AA2 6FC5810-0YC00-0YA8 6FC5810-0YC14-6YA8 6FC5810-0YC14-7YA8 6FC5810-1YC00-0YA8 6FC5810-1YC14-6YA8 6FC5810-1YC14-7YA8 6FC5810-1YG14-5YA0 6FC5810-1YG14-6YA0 6FC5810-1YG14-7YA0 6FC5810-1YP00-0YB0 6FC5810-2YC00-0YA8 6FC5810-2YC14-5YA8 6FC5810-2YC14-6YA8 6FC5810-2YC14-7YA8 6FC5810-2YG14-5YA0 6FC5810-2YG14-6YA0 6FC5810-2YG14-7YA0 6FC5810-2YP00-0YB0 6FC5810-3YG14-5YA0 6FC5810-3YG14-6YA0 6FC5810-3YG14-7YA0 6FC5810-3YP00-0YB0 6FC5810-4YG14-6YA0 6FC5810-4YG14-7YA0 6FC5810-4YP00-0YB0 6FC5810-5YG14-6YA0 6FC5810-5YG14-7YA0 6FC5810-5YP00-0YB0 6FC5810-6YG14-5YA0 6FC5810-6YG14-6YA0 6FC5810-6YG14-7YA0 6FC5810-6YP00-0YB0 6FC5880-3YC10-1AA8 6FC6000-6DA51-0AA0 6FC6000-6DB51-0AA0
6FC5103-0AB01-0AA4 6FC5103-0AB01-0AA4 ZhongHaiDe (Fujian) Industrial Equipment Co., Ltd., is located in the center of the provincial capital of Fujian Province, relying on the advantages of customs declaration in Mawei Free Trade Zone of Fuzhou, specializing in the import and export of various industrial automation products and technologies around the world. Our company has established stable relationships with globally renowned industrial companies such as Rexroth, Honeywell, Fanuc, Baily and so on in Europe, North America and North America for many years. The products are imported directly from abroad, eliminating the intermediate links in order to help the majority of business users to save money! At present, the company's business covers all provinces and cities across the country and some places abroad. After many years of service, we have concluded a mature model for service of system users. It has realized the humanization of services, the simplification of processes and the standardization of management, effectively helping customers extend the life cycle of electrical equipment and reduce Operating costs, control the risk of stop production, increase production efficiency! Our company has worked with more than 1,000 companies and has received lots praise from our customers. Among them there are a great deal of returning customers to buy out products. If you have something want to know or some products youre interested in, you can cantact the email: fjzhdcm@outlook.com or ayj897463393@gmail.com.also you can add wechat :15306912905. QQ:3004995626 Im glad to answer your doubts. 6FC5103-0AB01-0AA4 6FC5103-0AB03-0AA4 6FC5103-0AB03-1AA4 6FC5110-0DB02-0AA4 6FC5111-0CA02-0AA2 6FC5111-0CA03-0AA2 6FC5111-0CA04-0AA0 6FC5111-0CA05-0AA0 6FC5147-0AA00-0AA1 6FC5147-0AA07-0AA1 6FC5147-0AA15-0AA1 6FC5147-0AA20-0AA1 6FC5150-0AS45-0AA0 6FC5150-0AS50-0AA0 6FC5150-0AX01-3AE0 6FC5150-0AX01-3CE0 6FC5150-0AX01-3EE0 6FC5152-0AX01-2AA0 6FC5152-2AX01-1AA0 6FC5153-0AX01-2AF0 6FC5158-2AX01-3AF0 6FC5158-3AX01-1FF0 6FC5158-3AX01-1QF0 6FC5158-3AX01-2PF0 6FC5158-3AX11-2AF0 6FC5158-3AY11-1AF0 6FC5158-3AY11-2AF0 6FC5158-4AX01-4FF0 6FC5158-4AX01-4HF0 6FC5158-4AX01-4KF0 6FC5158-4AX01-4PF0 6FC5158-4AX01-4QF0 6FC5158-4AX01-8AF0 6FC5158-4AY01-8AF0 6FC5158-4BX01-8AF0
Product description HMCP003A0C Allen Bradley 100% new original,spot goods Trip current:220 Rated frequency:110 Rated insulation voltage:1 Product certification:UL The weight of the:10 kg Margin of error:220230260 type:Molded case circuit breaker The number of:3 p Arcing medium: Air type Mode of operation:Electric operation installation: stationary speed:Type fast structure: Plastic shell HMCP003A0C Allen Bradley 100 New Original Spot Goods Business scope: Programmable controller, the CPU module, I/o module, the DO module, module, AI DI module, communication module, Ethernet module, motor control module, analog input module, analog output module, digital input module, digital output module, redundant module, power module, relay output module, relay input module, CPU module
Starting Mode: Lever Start/Push Start Torque Range: 0.03-0.29N.m/0.3-3kgf.cm Free Speed:2000/1400 Machine Screw Size : 1.0~2.3mm Tapping Screw Size : 1.0~2.0mm Handle Diameter: Ã?32.2mm Length: 220mm Weight:
Starting Mode: Lever Start/Push Start Torque Range: 0.03-0.29N.m/0.3-3kgf.cm Free Speed:1000/700 Machine Screw Size : 1.0~2.3mm Tapping Screw Size : 1.0~2.0mm Handle Diameter: 32.2mm Length: 220mm Weight:
