General Information
Product ID: 3BSE038415R1
Medium Description: AO810V2 Analog Output Module, 8 channels, 0(4)...20mA
Technical Information: Supersedes 3BSE008522R1/3BSE038415Z1
Product Type: I/O Module
Country of Origin: Estonia /India
Customs Tariff Number: 85389091
Length: 102 mm
Height: 119 mm
Width: 45 mm
Weight: 0.19 kg
Description
The Trusted TMR 24V dc digital input module interfaces to 40 field input devices. A wide input voltage range and programmable thresholds allow the module to be used in current source and current sink configurations. Comprehensive diagnostic tests are performed on each input channel, including tests for stuck on and stuck off failures. Fault tolerance is achieved through Triple Modular Redundancy (TMR) within the same module for each of the 40 input channels.
When a line-monitoring device is installed at the field switch, the module can detect open and shorted field cables. Line monitoring can be independently configured for each input channel.
The module provides on-board sequence of events (SOE) reporting with a resolution of 1ms. A change of state triggers an SOE entry. States are determined by programmable voltage thresholds that can be configured on a per channel basis. When the field voltage and field return are connected to the auxiliary input channels of the module, thresholds can be specified as a ratio of the current field supply voltage.
Each triplicated section of the module, referred to as a slice, conditions and measures each channel independently. Each slice is optically isolated up to 2500V dc. Each slice sends its data to a safety layer hardware voter that presents the information from all three slices to the Trusted TMR processor. When a fault is detected on a slice of the module, the Trusted TMR processor will flag the error, indicating the need to replace the module. The Trusted TMR processor will continue to use the information provided by the remaining two slices until a replacement module is available. Replacement modules can be located in a standby slot next to the module or in a designated SmartSlot with a temporary connection to the same Trusted termination assembly.
Modules may be placed in any I/O module slot in a Trusted processor chassis or expander chassis. Once the I/O module configuration is set, mechanical keying is available on all I/O modules to prevent inserting a module into an incorrect slot.
Configuration of the module is carried out using the Trusted Toolset running on an engineering workstation. Once configured and loaded into the Trusted controller, replacement modules are online educated by the TMR processor.
Features
40 TMR input channels per module.
Comprehensive diagnostics and self-test.
Line monitoring on a per channel basis.
2500V dc optically isolation.
On-board 1ms resolution sequence of events reporting.
Hot replaceable.
Front panel status LEDs for each channel.
Module fault and status indicators.
IEC 61508, SIL 3 safety applications.
Description
The Trusted TMR 24V dc digital output module interfaces to 40 field output devices. Outputs are arranged in five groups of eight outputs. All outputs in a group share a common power source and return. Fault tolerance is achieved through Triple Modular Redundancy (TMR) within the same module for each of the 40 output channels.
The module provides on-board sequence of events (SOE) reporting with a resolution of 1ms. The event is the actual sensing of the field device loop current.
Each triplicated section (slice) of the module, receives output data from the Trusted TMR processor and sends its data to an internal safety layer hardware voter. Each slice uses the voted data to control the outputs. Every output channel consists of a six-element voted array. The output switch array provides fault tolerant, uninterrupted control under an output switch failure condition. Output switching and fault diagnostics comply with the demanding requirements of IEC-61508 SIL-3 for First fault - Fault tolerant, and Second fault Fail-safe outputs.
When a module fault is detected, the Trusted TMR processor will flag the unhealthy condition, indicating the need to replace the module. Control continues until a replacement (healthy) module is available. Replacement modules can be located in a standby slot next to the module or in a designated SmartSlot with a temporary connection to the same Trusted termination assembly.
Each output is user configurable to perform line monitoring of the connected field devices to detect field wiring and load failures. Automatic over-current protection is inherent in every output circuit which eliminates the need for fuses.
Modules may be placed in any I/O module slot in a Trusted processor chassis or expander chassis. Once the I/O module configuration is set, mechanical keying is available on all I/O modules to prevent inserting a module into an incorrect slot.
Configuration of the module is carried out using the Trusted Toolset running on an engineering workstation. Once configured and loaded into the Trusted controller, replacement modules are online educated by the TMR processor.
Features
40 TMR output channels per module.
Five isolated groups of eight outputs each.
Six-element voted output array.
Comprehensive diagnostics and self-test.
Guaranteed, First fault fault tolerant, Second fault fail-safe.
Line monitoring on a per channel basis.
Automatic over-current protection no fuses required.
2500V dc optically isolation.
Hot replaceable.
Front panel status LEDs for each channel.
Module fault and status indicators.
IEC 61508, SIL 3 safety applications.
On-board 1 ms resolution sequence of events reporting.
Description
The Trusted TMR 24 / 48V dc Digital Output module interfaces to 40 field devices. Triplicated diagnostic tests are performed throughout the module including measurements for current, and voltage on each portion of the voted output channel. Tests are also performed for stuck on and stuck off failures. Fault tolerance is achieved through a Triple Modular Redundant (TMR) architecture within the module for each of the 40 output channels.
Automatic line-monitoring of the field device is provided. This feature enables the module to detect both open and short circuit failures in field wiring and load devices.
The module provides on-board Sequence of Events (SOE) reporting with a resolution of 1ms. An output change of state triggers an SOE entry. Output states are automatically determined by voltage and current measurements on board the module.
Features
40 Triple Modular Redundant (TMR) output channels per module.
Comprehensive, automatic diagnostics and self-test.
Automatic line monitoring per channel to detect open circuit and short circuit field wiring and load faults.
2500V dc optical isolation barrier.
Automatic over-current protection (per channel), no fuses required.
On-board Sequence of Events (SOE) reporting with 1ms resolution.
Module can be hot-replaced on-line using dedicated Companion (adjacent) Slot or SmartSlot (one spare slot for many modules) configurations.
Front panel output status LEDs for each channel indicate output status and field wiring faults.
Front panel module status LEDs indicate module health and operational mode (Active, Standby, Educated)
TUV Certified IEC 61508 SIL 3
Outputs are powered in isolated groups of eight.
Each power group can be of a different voltage
Description
The Trusted TMR analogue input module interfaces to 40 single-ended field input devices. A wide input range and programmable thresholds allow the module to be used in most voltage or current configurations. Comprehensive diagnostic tests are performed on each input channel, including tests for out of range values and stuck at failures. Fault tolerance is achieved through Triple Modular Redundancy (TMR) within the same module for each of the 40 input channels.
The module can apply a digital filter to each input channel. Individual channels can be configured for high noise immunity (50Hz or 60Hz rejection), low noise immunity (fast response) or pass-through operation (no filtering).
Each input channel has four configurable state thresholds, which may be assigned to SOE reporting. A change of state triggers an SOE entry. The on-board sequence of events (SOE) reporting has a resolution of 1ms.
Each triplicated section of the module, referred to as a slice, conditions and measures each channel independently. Each slice is optically isolated up to 2500V dc. Each slice sends its data to a safety layer hardware voter that presents the information from all three slices to the Trusted TMR processor. When a fault is detected on a slice of the module, the Trusted TMR processor will flag the error, indicating the need to replace the module. The Trusted TMR processor will continue to use the information provided by the remaining two slices until a replacement module is available. Replacement modules can be located in a standby slot next to the module or in a designated SmartSlot with a temporary connection to the same Trusted termination assembly.
Modules may be placed in any I/O module slot in a Trusted processor chassis or expander chassis. Once the I/O module configuration is set, mechanical keying is available on all I/O modules to prevent inserting a module into an incorrect slot.
Configuration of the module is carried out using the Trusted Toolset running on an engineering workstation. Once configured and loaded into the Trusted controller, replacement modules are online educated by the TMR processor.
Features
40 TMR input channels per module.
Comprehensive diagnostics and self-test.
2500V dc optically isolation.
Digital signal filtering on a per channel basis.
Four user configurable thresholds per channel.
On-board 1ms resolution sequence of events reporting.
Hot replaceable.
Front panel status LEDs for each channel.
Module fault and status indicators.
IEC 61508, SIL 3 safety applications.
47856 Electrical Household Other Goods Components Suppliers
Short on time? Let Electrical Household Other Goods Components sellers contact you.
Description
The Trusted Field Termination Assembly (FTA) 24V dc Digital Input T8800 is designed to act as the main interface between a field device generating a digital signal and the Trusted TMR 24V dc Digital Input Module T8403.
Features
40 input channels per FTA.
Industry standard field device connections (2-wire).
Standard DIN rail compatibility.
Simple installation and connection.
24V dc operation.
SmartSlot connection for one to many hot replacement of input modules.
Fused field power supply per channel.
On-board LED indication field power supply integrity.
Description
The Trusted 40 Channel Analogue Input FTA T8830 is designed to act as the main interface between a field device generating an analogue signal and the Trusted TMR Analogue Input Module T8431.
Features
40 input channels per FTA.
Industry standard field device connections (2-wire).
Standard DIN rail compatibility.
Simple installation and connection.
24V dc operation.
SmartSlot connection for one to many hot replacement of input modules.
Fused field power supply per channel.
On-board LED indication field power supply integrity.
Description
The Trusted 40 Channel Analogue Output or Digital Output FTA is designed to act as the main interface between the Trusted TMR 24V dc Digital Output Module T8451 or Trusted TMR Analogue Output Module T8480 and Trusted the field device. The signal from the output modules are 24V dc and 0-20mA respectively.
Features
40 output channels per FTA.
Industry standard field device connections (2-wire).
Standard DIN rail compatibility.
Screw clamp terminals on both field and power.
Simple installation and connection.
24V dc operation.
SmartSlot connection for one to many hot replacement of output modules.
Field power supply arranged in five groups of eight channels, with OV isolation between groups.
On-board LED indication field power supply integrity.
Field terminal wire size allowance 12 to 28 AWG
Description
The Trusted TMR Analogue Output module interfaces to 40 field devices. Triplicated diagnostic tests are performed throughout the module including measurements for current, and voltage on each portion of the voted output channel. Tests are also performed for stuck on and stuck off failures. Fault tolerance is achieved through a Triple Modular Redundant (TMR) architecture within the module for each of the 40 output channels.
Automatic line-monitoring of the field device is provided. This feature enables the module to detect both open and short circuit failures in field wiring and load devices.
The module provides on-board Sequence of Events (SOE) reporting with a resolution of 1ms. An output change of state triggers an SOE entry. Output states are automatically determined by voltage and current measurements on board the module.
Features
40 Triple Modular Redundant (TMR) output channels per module.
Comprehensive, automatic diagnostics and self-test.
Automatic line monitoring per point to detect open circuit and short circuit field wiring and load faults.
2500V dc optical isolation barrier.
On-board Sequence of Events (SOE) reporting with 1ms resolution. Module can be hot-replaced on-line using dedicated Companion (adjacent) Slot or SmartSlot (one spare slot for many modules) configurations.
Front panel output status LEDs for each point indicate output status and field wiring faults
Front panel module status LEDs indicate module health and operational mode (Active, Standby, Educated)
TUV Certified for non-interfering applicatins
Outputs are powered in isolated groups of eight
Description
The Trusted TMR Analogue Output module interfaces to 40 field devices. Triplicated diagnostic tests are performed throughout the module including measurements for current, and voltage on each portion of the voted output channel. Tests are also performed for stuck on and stuck off failures. Fault tolerance is achieved through a Triple Modular Redundant (TMR) architecture within the module for each of the 40 output channels.
Automatic line-monitoring of the field device is provided. This feature enables the module to detect both open and short circuit failures in field wiring and load devices.
The module provides on-board Sequence of Events (SOE) reporting with a resolution of 1ms. An output change of state triggers an SOE entry. Output states are automatically determined by voltage and current measurements on board the module.
Features
40 Triple Modular Redundant (TMR) output channels per module.
Comprehensive, automatic diagnostics and self-test.
Automatic line monitoring per point to detect open circuit and short circuit field wiring and load faults.
2500V dc optical isolation barrier.
On-board Sequence of Events (SOE) reporting with 1ms resolution. Module can be hot-replaced on-line using dedicated Companion (adjacent) Slot or SmartSlot (one spare slot for many modules) configurations.
Front panel output status LEDs for each point indicate output status and field wiring faults
Front panel module status LEDs indicate module health and operational mode (Active, Standby, Educated)
TUV Certified for non-interfering applicatins
Outputs are powered in isolated groups of eight
Feature:
a. High resistance
b.Excellent resistance and minimum swell
c.Ultra high durability-longer lifespan
d.Precisely finished edges
e.Super solvent resistance
It is widely used in textile screen printing, high precise LCD, electronic printing, large advertisement, auto-printing machine, high precise multi-layered circuit board ect.
High precise LCD printing squeegees and polyurethane squeegees are our main product. Our product are widely used in textile screen printing, high precise LCD, electronic printing and so on.
More information you can view here
PTC thermistors current protector, also called PTC thermistor resettable fuses, protect load against over-current, overload, short circuit. No need for replacement, resume protective function after a short cooling-down time.
Ceramic PTC (positive temperature coefficient) thermistors are used instead of conventional fuses to protect load, such as motors, transformers, or electronic circuit, against overcurrent for circuit protection. PTC thermistor protector not only respond to inadmissibly high currents but also if a preset temperature limit is exceeded. PTC thermistor over-current protector limits the power dissipation of the whole circuit by increasing their resistance and thus reducing the current to a harmless residual value. In contrast to conventional fuses, PTC thermistor resettable fuses do not have to be replaced after elimination of the fault but resume their protective function immediately after a short cooling-down time.
PTC Thermistor Over-current Protector Application
It applies in the over-current overload and short circuit protection of transformers, battery charger, switches, switch power supply, adaptor, meter, instrumentation, apparatus, electronic coils, control panels, air conditioner, automotive electron, etc.
Operating Principle of PTC Thermistor for Overload Over-current Protection
The operating principle is as indicated in the following. When a circuit is in the normal status, the current through PTC is lower than the rated current and PTC thermistor protector is in the normal state with small resistance value, which will not affect the normal operation of the protected circuit. In case of some fault in the circuit and the current is greater than the rated current, the PTC thermistor protector will become hot quickly and present a high resistance state, which sets the circuit relatively "off" to protect the circuit from damage. After the fault is removed, PTC thermistor protector will automatically restore its low resistance state and the circuit will resume normal operation.
Normally, when PTC thermistor is used as an overcurrent protection component, it is preferred to select maximum operating current, maximum operating voltage and proper specifications. Furthermore such factors should be taken into consideration as the dimensions of the components, rated zero-power resistance, operating temperature range, etc.
ABB is a Swiss-Swedish multinational corporationheadquartered in Zurich, Switzerland, operatingmainly in robotics, power, heavy electrical equipmentand automation technology areas. It is ranked 341stin the Fortune Global 500 list of 2018 and has been aglobal Fortune 500 company for 24 years.
What you care about
Packaging Details:Original packaging
Port: Xiamen
Lead Time :In Stock
Warranty: one year
Payment term: T/T
More brand
----(DCS)Distributed Control System
AB Invensys Foxboro Invensys Triconex Ovation Woodword
HIMA Yokogawa Honeywell Emerson
----(PLC)Programmable Logic Controller
Rockwell Allen-Bradley Schneider Modicon GE Fnauc Siemens Prosoft Bachmann Woodhead
----(TSI) Bently Nevada
EPRO ENTEK
Who we are?
Cambia Automation Limited company to give customers the best service and the best quality products as the focus of work, with 20 years of service experience, to ensure you the best service, welcome to consult.
What you care about
Packaging Details:Original packaging
PortXiamen
Lead Time :In Stock
Warranty: one year
Payment term: T/T
More brand
----DCSDistributed Control System
AB Invensys Foxboro Invensys Triconex Ovation Woodword
HIMA Yokogawa Honeywell Emerson
----PLCProgrammable Logic Controller
Rockwell Allen-Bradley Schneider Modicon GE Fnauc Siemens Prosoft Bachmann Woodhead
----TSI Bently Nevada
EPRO ENTEK
Who we are?
Cambia Automation Limited company to give customers the best service and the best quality products as the focus of work, with 20 years of service experience, to ensure you the best service, welcome to consult.
General Information
Extended Product Type : RT6 24DC
Product ID : 2TLA010026R0000
EAN : 7350024431858
Catalog Description : Safety Relay RT6 24DC
Long Description : A universal safety relay for many safety applications. Relay outputs 3NO/1NC
Popular Downloads
Instructions and Manuals 2TLC172028M9801
Dimensions
Product Net Depth / Length : 120 mm
Product Net Height : 84 mm
Product Net Width : 45 mm
Product Net Weight : 0.33 0 kg
Certificates and Declarations (Document Number)
Declaration of Conformity - CE : 2TLC172078D0201
Instructions and Manuals : 2TLC172028M9801
47856 Electrical Household Other Goods Components Suppliers
Short on time? Let Electrical Household Other Goods Components sellers contact you.
