Microwave ferrite(A50) for phase shifter Li Zn - Ti - Mn - (Co) Lithium - Zinc - Titanium Manganese - (Cobalt) MS(Gauss) :5000gs±5% Tc (°C) :450 H (Oe) 170 ±20% Hk (Oe) 3±5% DIELECTRIC CONSTANT15.3 DIELECTRIC LOSS TANGENT 0.0005 Br (Gauss) 3300
Microwave ferrite(A50) for phase shifter Li Zn - Ti - Mn - (Co) Lithium - Zinc - Titanium Manganese - (Cobalt) MS(Gauss) :5000gs±5% Tc (°C) :450 H (Oe) 170 ±20% Hk (Oe) 3±5% DIELECTRIC CONSTANT15.3 DIELECTRIC LOSS TANGENT 0.0005 Br (Gauss) 3300
Disc Microwave ferrite for the isolator(6kw 2.45ghz ) in MPCVD in Artificial diamond industry. Size D50.82*3.82 Tolerance ±0.02mm Material CY1000 Price 50USD/PC
Microwave ferrite substrate: Size:60*48*1mm;60*48*0.5mm;48*30*1mm;48*30*0.5mm SATURATION MAGNETISATION (GAUSS):1750-1800 DIELECTRIC CONSTANT:15,0 ±5% DIELECTRIC LOSS TANGENT: 0.0002 CURIE TEMPERATURE (NOMINAL VALUE)(°C):280 LINE WIDTH (Oe):25 SPIN WAVE LINE WIDTH (Oe):2 FINISH: CLEAN.
Microwave ferrite with special-shaped ceramic dielectric ring
Microwave ferrite(Grade:A50 ) for X-Band high power ferrite phase shifter
Metallized YIG Microwave ferrite substrate Technical requirements: 1- The Ferrite Thickness should be 0.37mm. In the process of ferrite production, fine grinding method should be used. The surface of the ferrite should be polished (To reduce the roughness). Material:CY1780 2- Use a soft gold coating. Clad layer: Cu1m4mAu2.5m5.7m. The plating thickness should be 8~10m(Red area ). 3- The bottom side will be attached to a Gold plated carrier by soldering. The solder paste model can be Pb63Sn37. The carrier material is Iron. Clad layer: Cu36mNi14m Au12m. The final carrier dimensions (after plating) are 12mm X 9mm X 0.5mm. 4- The resistive layer should be 75 Ohm/Sq. The final resistor should be 50 Ohm (+/-10% tolerance) (Green area)
Metallized microwave ferrite substrate for antenna use.
Microwave dielectric ceramic: Dielectric constant 50 @4.6GHz
Triangle microwave ferrite(Li series) for X- band frequency, 8.2 to 12. 4 ghz.
A50 Ferrite Toroid for phase shifter, phased array radar
TTVG-1850 Microwave ferrite for microwave switch
Part name: TI IC TPS5430DDAR PN: TPS5430DDAR Package: SOP-8 Brand: TI Factory Packing QTY: 200PCS Condition: original new
Part name: Tianbo relay HJR-3FF-S-Z-5VDC PN: HJR-3FF-S-Z-5VDC Package: SMD Brand: Tianbo Factory Packing QTY:/ Condition: original new
Part name: YXC HC-49S 25MHZ 20PPM 20PF PN: HC-49S 25MHZ 20PPM 20PF Package: / Brand: YXC Factory Packing QTY: 50 Condition: original new
POPULA FX Series Purifying Box Product Feature: It is equipped with multi-layer filter and activated carbon , high efficiency and filter PM2.5 and purify air.It can used with a silent fan,suitable for a variety of small hidden installation environments. PRODUCTS INFO: Type:POPULA FX Series Purifying Box Brand:POPULA Electric Current:AC Voltage:1HP/3HP 110V/220V/380V/440V/3KV/6KV Frequency: 50/60HZ Air Volume:100-2000 M3/h Air Pressure:30-180 Pa Max Noise:
IC640WMI610 DISCONTINUED BY MANUFACTURER INTERFACE BOARD FOR WORKSTATION FACTORY WARRANTY MAY NOT APPLY. RADWELL 2-YEAR WARRANTY INCLUDED
The 3500/15 AC and DC Power Supplies are half-height modules and must be installed in designated slots on the left side of the rack. The 3500 rack can contain one or two power supplies with any combinations of AC and DC. Either supply can power a full rack. When two power supplies are installed in a rack, the one in the lower slot acts as the primary supply, and the other in the upper slot acts as the backup supply. If installed, the second supply is the backup for the primary one. Removing or inserting either power supply module does not disrupt operation of the rack as long as a second power supply is installed. The 3500/15 AC and DC Power Supplies accepts a wide range of input voltages and converts them to voltages acceptable for use by other 3500 modules. The following power supplies are available with the 3500 Series Machinery Protection System: Universal AC Power High Voltage DC Power Supply Low Voltage DC Power Supply
Round peltier module TES1-04103 Size: 25* 4*3.6mm Imax.: 3.0 A Vmax.: 4.8 V Qmax.: 8.61W Tmax.: 68 degree Solder melting point: 138degree Maximum. Compress.: 1Mpa
Peltier modules TES1-12704 Size: 30*30 *3.2mm Internal resistance: 3.08 Ohm +/- 10% Imax.: 4.0 A Vmax.: 15.4 V Qmax.: 35.6W Tmax.: 68 degree Solder melting point: 138degree, 150degree, 200degree. Maximum. Compress.: 1Mpa
