1. Description of food grade liquid silicone rubber for making mould Addition-curing, Food grade, Translucent, Two-component mold making silicone. 2. Characteristics of food grade liquid silicone rubber for making mould Acceptable for food contact Outstanding release properties Low viscosity Easy mixing and degassing High flowability Odorless and Nontoxic Enhanced durability 3. Application of food grade liquid silicone rubber for making mould Food Grade Related Applications Cake mold Chocolate moldmaking Candy moldmaking Baking moldmaking Ice trays molding Casting butters Casting for Kitchen products 5. Using instructions of food grade liquid silicone rubber for making mould Step 1: Prepare and clean the prototype. You must make sure your original molds perfect, fix the original mold on a board, then using some assistant material (like cardboard) to make a frame for to surround the prototype. The frame is no need, if we make the mold by brushing way. Step 2: Take the silicone and catalyst as the ratio 100:2 (silicone : catalyst= 100:2), mix the silicone rubber and catalyst evenly. Notes: rtv silicone rubber is a kind of flowing liquid and it contains two parts. Part A is a kind of flowing liquid and part B is the curing agent. Remember to mix part A and part B evenly, otherwise the silicone rubber will be partly solidified and this will bring troubles for your final operation. What's more, the finishes molds will have a short life. All of these will cause a waste of silicone rubber. Step 3: Vacuum pumping. After mixed the silicone evenly, it is better to release the bubble by vacuum pumping. Step 4: Pouring cast or brushing cast. After released the bubble, we can pour/brush the silicone rubber on the prototype. Notes: Please finishes all the steps within the operation time. If not, it will cause cross linking reaction, and no more further steps will be available. So, we have to pay attention to the pot life and curing time. Packaging & Shipping Packing: 20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B 200KG/drum packing for part A +200KG/drum packing for part B
1.Description of life casting rtv-2 silicone rubber for prosthetic hands RT-810 silicone rubber is platinum cure silicone rubber with medical grade , it belong to be life casting silicone rubber. The silicone rubber will be cured under room temperature and can be cured under room temperature and can be fastly by heating. It's two components liquid silicone rubber, the mixing ratio is 1:1. It has an exceptional fluidity and good operability. Especially, the platinum cure silicone rubber has a lower shrinkage, higher temperature resistance G810 is extremely soft as a real feeling as humman skin 2.Characteristics of life casting rtv-2 silicone rubber for prosthetic hands *An exceptional fluidity and good operability *Good tensile strength and tear strength *Food grade silicone rubber *high temperature resistance *good flexibility *No smell ,non-toxic *long shelf-time &lifetime *Lower shrinkage 3.Datesheet of life casting rtv-2 silicone rubber for prosthetic hands Item No. Hardness (A°) Viscosity (CS) Tensile-strength ( kgf /cm2 ) Tear-strength (kgf /cm2 ) Elongation-break(%) Mixing ratio operation time (25 ? ) Curing time ( 25 ?) shrink-age RT-810 10 5000 40±5 10±2 450±50 1:1 20-30 mins 2~3 h =0.1% Notice of life casting silicone for prosthetic limbs RT-810 life casting silicone rubber is platinum cure silicone , which is very easy to cause cure inhibition , so please do remember thoroughly clean the model and tool before operation . Besides , please avoid the condensation silicone rubber (100:2) contact or mix with the following material , otherwise the silicone won’t be cured : 1. Liquid condensation silicone ( condensation silicone not completely cured or organic tin compounds ) 2. Sulphur, sulfide and sulfur rubber materials. 3. Amine compounds as well as contains the amine materials. 4. Pewter solder flux. Packaging & Shipping Packing: 20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B 200KG/drum packing for part A +200KG/drum packing for part B
1. Description of rtv 2 liquid silicone rubber for frame gypsum molds C830 silicone rubber is condensation cure silicone rubber (tin cure silicone rubber) for mold making. The silicone rubber will be cured under room temperature. It's two components, the mixing ratio is 100:2. Part A is a flowable liquid silicone, part B is the catalyst. It has an exceptional fluidity and good operability. 2. Characteristics of rtv 2 liquid silicone rubber for frame gypsum molds * An exceptional fluidity and good operability, easy to demold * Good tensile strength and tear strength * Suitable hardness * Copy detailed pattern * Good flexibility * Eco-friendly * Long shelf-time &lifetime 3. Application of rtv 2 liquid silicone rubber for frame gypsum mold C830 liquid silicone rubber is perfect molding material, it is suitable to make mold for concrete casting, artificial stone, brick, cement casting, gypsum decorations, plastic product, resin craft, polyester, polyurethane, bronze casting, statues, jewelry, wax, crystal, tire mold, shoe mold, clay casting, ceramic casting. etc. C830 liquid silicone rubber is mainly suitable for small or middle sized products with delicate pattern by pouring and brushing operation. Package 1kg/drum,5kgs/drum,20kgs/drum,25kgs/drum,200kgs/drum. Shelf life and transportation 1. Twelve(12) months when stored at 25C in tightly closed original packages. 2. This kind of product is non-dangerous product, which could be transported as general chemicals.
Cas no: 7440-02-0 Eninec no: 231-853-9 Mf: ni Grade standard:industrial, reagent Purity:20nm 99.9%. 40nm, 70nm, 100nm 99.8% Appearance: black powder Application:catalyst Size: 20nm 40nm, 70nm, 100nm Shape:spherical Note: we can supply different size products of electrode materials nickel powder according to client's requirements. Product performance Nickel nanoparticles is a high-performance electrode materials in fuel cells which can replace the precious metals platinum, thus greatly reducing the cost of the fuel cell.
Addition Cure rtv-2 Liquid Silicone Rubber for Concrete & Stone moulds Artificial Stone & Concrete Casting Silicone Rubber Features: Amazing fluidity and easy to operate Platinum-based, food-grade silicone (environmental friendly, odorless -and non-toxic) Delicate design available Mixing ration: 1:1, easy to mix Easy de-molding Excellent tension and tear strength High performance in duplication Shrinkage is almost zero (below 0.1) Excellent resistance to weather, temperature, aging, acid and aging-proofing. High resistance to high temperature and aging(resist -60â?? to 250â??) Appearance: Part A:a non-toxic and odorless liquid with translucent color and platinum inside. Part B: a non-toxic and odorless liquid with translucent color. ATT: We can do any curing time as your requirements. Technical Data Characteristics of the non cured product Properties G-820 G-825 G-830 G-835 G-840 A B A B A B A B A B Appearance low viscous liquid Colour translucent Density [g/cm 3 ] at 23 �°C, approx 1.10 1.10 1.10 1.10 1.10 Viscosity [mPa�·s] at 23 �°C, approx 5000�±1000 6000�±1000 7000�±1000 8000�±1000 9000�±1000 Polymerisation Curing conditions: 1h at 80 �°C Properties G-820 G-825 G-830 G-835 G-840 Hardness Shore A 20�±2 25�±2 30�±2 35�±2 40�±2 Tensile strength [N/mm 2 ] 45�±10 50�±10 55�±10 55�±10 60�±10 Elongation [%] 500�±50 500�±50 450�±50 450�±50 450�±50 Tear strength [N/mm] 22�±2 24�±2 26�±2 24�±2 12�±2 Application: GC RTV silicone G-8 series are great for artificial stone casting. They are widely used for architectural elements, block-outs & hole former, concrete counter tops, flexible form liners, GFRC, manufactured stone veneer, ornamental precast & statuary, stamped & textured concrete, etc. Operation Method: Both pouring and brushing operation methods for our artificial stone casting silicone are available. You can choose the best one as your preference, we can provide thixotropic agent for brushing. Notice What is the hardness should I choose? Normally 20~40 Shore A will be the best, but it also should according to your size and pattern design. Warm Tips: The surfaces with which the material comes in contact must be perfectly clean, free of grease and dry. Close the bottles after use so as not to confuse the cap of the catalyst with that of the base when re-sealing. Be aware of possible cross-contamination; it's highly recommended to use only dedicated gear when processing poly-addition RTV2 silicone rubber (including degassing devices). Be aware that contact with certain material can inhibit the curing of the RTV2 poly-addition silicone rubber. Common contaminants to be avoided include: -Natural or synthetic rubber, vulcanized with sulphur derivatives. -Poly-condensation RTV catalyzed with metallic salts. -PVC stabilizing agents. -Amine cured epoxies. -Sulphur, tin and amines derivatives. -In case of doubt, carry out a small test by pouring the mixture onto a small area of the object.
High transparent addition cure silicone for Jewelry mold making is a kind of two part silicone rubber in addition cure or platinum cure type with mixing ratio of 10:1. It can be cures at room temperature as well as under heat. It's a kind of food grade silicone ,And mainly used for jewelry mold making. High transparent addition cure silicone for Jewelry mold making is pourable, addition-curing, two-component silicone rubber that vulcanizes at room temperature or by heating. Non-toxic, odorless.Resistance high temperature is 250, shrinkage rate lower than 0.1%. It is great to make molds either with simple or intricate patterns,like artificial jewelry, resin Jewelry , artificial necklace, artificial bracelet etc. silicone molds serve very good performance in reproduction process with every fine detail on designing models.
China liquid Silicone mold making material for concrete/artificial stone casting Artificial Stone & Concrete Casting Silicone Rubber 1. Description C-825/C-830/C-835 Silicone Rubber is a two-part, tin-catalyzed, liquid silicone system that cures (RTV) to a white, Shore A25-A35 rubber. This is a pourable rubber, but it can be easily thickened with Liquid Thickener or for brush-on application. Popular product options is C-825/C-830/C-835 are the mold material of choice for high-volume veneer stone production (manual or automated manufacturing). These two-component mold rubbers capture excellent surface detail, offer exceptional dimensional stability and have unmatched lifetime and durability compared to hot melt and polypropylene systems. Molds made from these room temperature curing systems can be completed in a much shorter timeframe (~4 hour demold) compared to latex rubber molds. When properly maintained, these molds can last for years and produce thousands of stones. 2. Technical Datasheet Note: This is a 100A:3B mix ratio product that must be measured by weight. The choosing of suitable hardness should be according to the size and pattern design of the products. If large products and therefore multiple-piece molds are needed by customers, silicone rubber with higher hardness will be required for the molds. Conversely, soft silicon is indispensable for molds with complicated pattern and delicate details. The amount of curing agent admixture depends on the actual need of customers. More will be added for speedy drying and fast release and less when otherwise. 3.Application
Factory price rtv2 silicone rubber for crafts molding Crafts Molding Silicone 1.Description 2. Technical Datasheet Typical general characteristics Inspection MethodValue Product data (Catalyzed A+B)C-820C-825 HardnessShore A20±225±2 Mix RatioA:B100:3100:3 Color/WhiteWhite Pot life25 °C (77F)30-40mins30-40mins Curing time25 °C (77F)3-4 hours3-4 hours Mixed viscositymPa.s16000±100020000±1000 Tear-strengthkg/cm20±222±2 Tensile-strengthM.pa3.6±0.54.0±0.5 Elongation%400±50450±50 Shrinkage%?¤0.3?¤0.3 Note: This is a 100A:3B mix ratio product that must be measured by weight. The choosing of suitable hardness should be according to the size and pattern design of the products. If large products and therefore multiple-piece molds are needed by customers, silicone rubber with higher hardness will be required for the molds. Conversely, soft silicon is indispensable for molds with complicated pattern and delicate details. The amount of curing agent admixture depends on the actual need of customers. More will be added for speedy drying and fast release and less when otherwise. 3. FEATURES Low viscosity,great flexibility,Extra low shrinkage,Chemical resistance,release properties, Easy to work with,High tear strength,Heat Resistance,various color is available,High reproduction rate 4.SHELF LIFE: When stored at or below 32°C (89.6°F) in the original unopened containers, C-8 series Silicone Base and its Curing Agents have a usable life of I0 months. 5.Package Silicone base:1kg/drum; 20kg/drum;25kg/drum;200kg/drum. Curing Agent: 30g/bottle; 1kg/bottle
Cheap liquid silicone rubber to make molds for lost was casting Lost Wax Casting Silicone 1.Description GC RTV silicone C-825 are good for lost wax casting. They are widely used for lost wax process of bronze casting to make accurate reproductions of original sculpture. 2. Technical Datasheet Typical general characteristics Inspection MethodValue Product data (Catalyzed A+B)C-825 HardnessShore A25±2 Mix RatioA:B100:3 Color/White Pot life25 C (77F)30-40mins Curing time25 C (77F)3-4 hours Mixed viscositymPa.s20000±1000 Tear-strengthkg/cm22±2 Tensile-strengthM.pa4.0±0.5 Elongation%450±50 Shrinkage%?¤0.3 Note: This is a 100A:3B mix ratio product that must be measured by weight. The choosing of suitable hardness should be according to the size and pattern design of the products. If large products and therefore multiple-piece molds are needed by customers, silicone rubber with higher hardness will be required for the molds. Conversely, soft silicon is indispensable for molds with complicated pattern and delicate details. The amount of curing agent admixture depends on the actual need of customers. More will be added for speedy drying and fast release and less when otherwise. 3. FEATURES Low viscosity,great flexibility,Extra low shrinkage,Chemical resistance,release properties, Easy to work with,High tear strength,Heat Resistance,various color is available,High reproduction rate 4.Appearance Part A: Silicone rubber is a white liquid Part B: Catalyst is a non-toxic and odorless liquid, white transparent color. ATT: We can provide fast/medium/slow catalyst of for hot, warm or cold season. 5.SHELF LIFE: When stored at or below 32C (89.6F) in the original unopened containers, C-8 series Silicone Base and its Curing Agents have a usable life of I0 months. 6.Package Silicone base:1kg/drum; 20kg/drum;25kg/drum;200kg/drum. Curing Agent: 30g/bottle; 1kg/bottle
China supplier Rtv mould making Silicone rubber for Taxidermy Molding Taxidermy Molding Silicone 1.Description 2. Technical Datasheet Typical general characteristics Inspection MethodValue Product data (Catalyzed A+B)C-810C-825C-830 HardnessShore A10±225±230±2 Mix RatioA:B100:3100:3100:3 Color/WhiteWhiteWhite Pot life25 °C (77F)30-40mins30-40mins30-40mins Curing time25 °C (77F)3-4 hours3-4 hours3-4 hours Mixed viscositymPa.s6000±100020000±100023000±1000 Tear-strengthkg/cm12±222±223±2 Tensile-strengthM.pa2.0±0.54.0±0.55.0±0.5 Elongation%320±50450±50460±50 Shrinkage%?¤0.3?¤0.3?¤0.3 Note: This is a 100A:3B mix ratio product that must be measured by weight. The choosing of suitable hardness should be according to the size and pattern design of the products. If large products and therefore multiple-piece molds are needed by customers, silicone rubber with higher hardness will be required for the molds. Conversely, soft silicon is indispensable for molds with complicated pattern and delicate details. The amount of curing agent admixture depends on the actual need of customers. More will be added for speedy drying and fast release and less when otherwise. 3. FEATURES 1.Low viscosit 2.great flexibility 3.Extra low shrinkage 4.Chemical resistance 5.release properties 6.Easy to work with 4.High tear strength 5.Heat Resistance 6.various color is available 7.High reproduction rate 4.SHELF LIFE: When stored at or below 32°C (89.6°F) in the original unopened containers, C-8 series Silicone Base and its Curing Agents have a usable life of I0 months. 5.Package Silicone base:1kg/drum; 20kg/drum;25kg/drum;200kg/drum. Curing Agent: 30g/bottle; 1kg/bottle
Mc pu series, hardness available from 15 shore a to 95 shore a Mix ratio 1 1 De-mold time 8hrs 6hrs 3hrs Full cure 24hrs Why choose mc polyurethane rubber? Firm yet flexible mold rubbers Ideal for demanding, high production casting and forming of concrete Dimensionally stable molds can last for years Abrasion resistant for long mold life Easy to use, forgiving formulations All products share the same high performance Package: A and b 1kg, 5kg, 20kg, 200kg
Description of platinum curing mould making liquid silicone rubber Addition cure silicone is a kind of two part silicone rubber in addition cure or platinum cure type with mixing ratio of 1:1 or 10:1. It can cure at room temperature as well as under heat. It's a kind of food grade silicone and mainly used for mold making. Application of platinum curing mould making liquid silicone rubber Silicone rubber is mainly used for making molds of tire, concrete stone, grc, polyurethane products; wax, candle decoration; rapid prototyping and tyre molds; chocolate, candy and similar products.
1.Unsaturated polyester resin, epoxy resins, polyurethane resins 2.Polyurethane elastomers 3.Natural and synthetic waxes 4.Plasters and cements Features of silicone rubber 1.Curing agent arrange together as free charged. 2.In liquid form and in various colors 3.With and exceptional fluidity and good operability 4.Temperature and deformation resistance as well as low shrinkage 5.High duplication times6.Samples orders are available 7.Moq:200kg Silicone rubber are generally named: Two-component room temperature vulcanization silicone rubber , a kind of elastic silicone rubber mold which features with resistance to deformation.High-temperature, acid-alkali and expansion, it mainly applicable to make the silicone mould for cultural relic duplication , architectural decoration, resin crafts , lighting ornaments , candles , statues mold design, product exploitation etc. Instruction for using silicone rubber for mold making to make molds. Step 1:preparing mold. Once you have your model to mould you need to build a box from wood/acrylic to contain the silicone and get a good covering over your model , the size and shape of this container is totally depends on shape of the model , remembering to leave plenty room surrounding the model so that you will have a strong wall thickness (at least 20mm) Note:small models can be cast in sourced containers like tins , ice buckets , cake tins, etc
Specification : 1.100% food grade silicone material, nontoxic to humans body, with environmental protection 2. Temperature range:-40~260 centigrade 3. Unbreakable, pliable, and not fragile 4. Non-stick finish, durable and easy to clean 5. Suitable for microwave oven and deep-freezer 6. Different style and color available 7. Pattern and logo can be emlbossed, debossed and silk printed on bowl 8. Any color and size available 9. Oem orders are welcomed 10. It is good and necessary part of the household and kitchen
OVERVIEWThis silicone is used for matte top printing for matte effect. It's not suitable to be printed directly on fabrics. It can be applied on automatic screen printing production mixed with 2% catalyst with long working time. Super soft hand-feel you will always like it.TYPICAL PROPERTYCode NO. T-M02ColorTransparentDurometer - Shore A17 Shore ADynamic Viscosity100000 CentipoiseElongation566 %Pot Life72 hoursShelf Life360 DaysSolids Content> 98 %Specific Gravity @ 25C0.95Tear Strength2.3MpaTensile Strength1015.3 psiPACKING Â 5kg/barrel; 20kg/barrelCLEANING After printing, , silicone can be cleaned away from equipment with hydrocarbon based solvent.PRODUCT DISPLAY Â FAQ1.What is your MOQ?It depends on customer's exact request.2.Are you manufactuer or trading company?We are silicone ink and silicone heat transfer labels manufacturer, but we also do some trading according to customers trust.3.Where is your main market?Our main market based in Asian and south America countries where there are more printing factory for garments, shoes or textile accessories.4.What is your lead time?Normally in 3~15 days according to order quantity.5.What is your payment payment ?T/T, Western Union, PayPalAFTER SALES1. All silicone base is mixed with 2-5% catalyst, too few or too much would affect the curing of silicone.2. Our silicone base can be mixed in proper rate to improve related functions.3. The order we delivered if its not match your request, pls keep it sealed well for replacement.4. Curing temperature of silicone is 100-120 degree. Silicone need to be flash cure before another layer.5. Two way to get matte effect, print matte on top, or use very thin mesh to print high density silicone layer by layer.
OVERVIEWThis silicone is used for glossy top printing to get super shiny effect. Its in two-component which mixed with 2%-5% catalyst. After finished glossy printing, , we need to leave some time for bubble out, this is why its hard to people to get curve glossy effect without bubble. Heat too urgent or leave no enough time for bubble out, it would show easily in silicone with bubble. This silicone bubble would disappear within 20 seconds which is much better for machine production.TYPICAL PROPERTY Code NO. T-J04ColorTransparentDurometer - Shore A31 Shore ADynamic Viscosity200000 CentipoiseElongation520 %Pot Life72 hoursShelf Life360 DaysSolids Content> 98 %Specific Gravity @ 25C0.95Tear Strength4.1MpaTensile Strength1015.3 psiPACKING Â 5kg/barrel; 20kg/barrelCLEANING After printing, silicone ink can be cleaned away from equipment with hydrocarbon based solvent.PRODUCT DISPLAY Solution to 3 Printing Issue1.How to defoam the bubble in glossy silicone ?Print thinner layer to help bubble out;Dont heat too urgent, leave some time for leveling after printing finished;Add 10% bubble-defoaming agent DS-1003 to speed leveling.2.How to improve adhesion between silicone and fabrics ?Add enough catalyst to make complete cure during printing;Test the adhesion for adhesion before bulk production;Print our adhesive agent 1001 first on waterproof fabrics to improve adhesion.3.How to solve sticky surface of silicone printing ?make sure catalyst added enough due to different weather and room temperature;heat under curing temeperature, usually under 100-120 degree;avoid to add too much pigment or other addive agent in silicone, this would also affect curing.
Quick Details Table Decoration & Accessories Type: Mats & Pads Material: Silicone Feature: Eco-Friendly Place of Origin: Guangdong, China (Mainland) Brand Name: lifetop Model Number: felt glass coaster Item: felt glass coaster Color: any color in pantone Packaging: poly bag or customized Logo: customized MOQ: 1000 pcs Certification: FDA LFGB Sample: available weight: 15g size: Dia80mm material: silicone
Quick Details Use: Credit Card Material: PVC Brand Name: lifetop Model Number: card holder rfid Item: card holder rfid Color: any color in pantone Packaging: poly bag or customized Logo: customized MOQ: 500 pcs Certification: FDA LFGB Sample: available weight: 30g size: 95*58*6mm material: silicone
Quick Details Type: Baking & Pastry Tools Baking & Pastry Tools Type: Baking & Pastry Spatulas Material: Metal Certification: FDA, LFGB, FDA LFGB Feature: Eco-Friendly Place of Origin: Guangdong, China (Mainland) Brand Name: lifetop Model Number: icing spatula Item: icing spatula Color: dark red and silver Packaging: poly bag Logo: customized MOQ: 100sets Sample: available weight: 18g,58g,61g,91g size: 4inch,6inch,8inch,10inch material: wood and stainless steel
Quick Details Place of Origin: Guangdong, China (Mainland) Brand Name: lifetop Model Number: Exercise Hand-muscle Developer Item: Exercise Hand-muscle Developer Color: yellow,blue,geen,orange Packaging: poly bag or customized Logo: customized MOQ: 500 pcs Certification: FDA LFGB Sample: available weight: L:97G, S:45G,mini:40g color-poundage: yellow-40LB,blue-50LB,green-60LB,orange-70LB Material: silicone Item Name Personalized Heat Resistant Anti-slip silicone felt glass coaster Material 100%food grade silicone Color any color in pantone Feature 1.Eco-friendly,harmless,non-toxic 2.Working temperature:-40-230 C 3.Easy to clean and suitable to use 4.Logo can be printed,embossed,debossed MOQ1000 pcs Package 1.Inner packaging:1pc/opp bag 2.Outer packaging:carton Custom package acceptable CertificateFDA;LFGB;ROHS, Payment\T/T;L/C;Western Union Delivery15 to 20 days
