The raw materials for tiles can be : Cement,Concrete,Sand,Stone powder,Crushed stone etc.
HFT300, this machine can produce different sizes of tiles: 300x300mm, 400x400mm, 500x500mm, 600x600mm.
Terrazzo Floor Tile Application:
- Swimming Pool, Courtyard, Civil Architecture
- Square,Sidewalk,
- Hospital,Kitchen,Washroom,School, Public Institution, Office Building,etc.
-1. Special designed for manual operation,low investment, high efficiency
- 2.Two molds at both sides, can produce terrazzo tiles at the same time
-3. Hydraulic pressure guarantees the high density of the terrazzo tile
- 4.The tile machine easy operation,low maintenance rate
- 5.HFT300 terrazzo tile machine can produce floor tile,pave brick,paving tile,garden tile, with customized pattern.
- 6.The machine can install with Pan mixers.
- 7.Only three or four workers can run the terrazzo tile molding machine.
- 8. Power: 18.5KW
- 9. Other machine in production line: polishing machine(automatic/manual)
Best Machinery Parts International Limited is a professional construction machinery parts supplier for excavator, bulldozer, loader. Including models Komatsu, Hitachi, Kobelco, CAT, Isuzu, Cummins,Volvo, Shantui, XCMG, SEM.
Main products : travel motor, swing motor , hydraulic pump and parts, complete engine and engine parts, operator cabin, undercarriage parts
FM-25 is professional mobile machine for foam concrete.
1. Structure
FM-25 includes four parts, a belt conveyor (screw feeder), a mixer, a pump and a built-in foam
generator inside the pump. The machine is easy to install, dismantle, transport, and construct at site.
The machine has been fully debugged in factory.
FM-25 is a mobile unit which blends foam concrete from sand, cement, water, foaming agent directly at the building site. The machine continually mixes all ingredients mechanically, which allows for fresh concrete with the best properties. The process is controlled and supervised by a control panel.
At least four people are required to run the machine, one machine operator who control machine, two provides the machine with raw materials and one person to place the foam concrete in a mold.
The machine is easy to service thanks to the well-known component manufacturers which produces the high quality coupon.
FM types machines are professional equipment for foam concrete.
1. Structure
It includes four parts, a belt conveyor, a mixer, a pump and a built-in foam generator inside the
pump. The equipment is easy to install, dismantle, transport, and construct at site. The equipment
has been fully debugged in factory.
It is a mobile unit which blends foam concrete from sand, cement, water, foaming agent directly at
the building site. The machine continually mixes all ingredients mechanically, which allows for
fresh concrete with the best properties. The process is controlled and supervised by a control panel.
At least four people are required to run the machine, one machine operator who control machine,
two provides the machine with raw materials and one person to place the foam concrete in a mold.
The machine is easy to service thanks to the well-known component manufacturers which produces
the high-quality components. Cleaning can be done on site with the built-in high-pressure hose.
FM types machines are professional equipment for foam concrete.
1. Structure
It includes four parts, a belt conveyor, a mixer, a pump and a built-in foam generator inside the
pump. The equipment is easy to install, dismantle, transport, and construct at site. The equipment
has been fully debugged in factory.
It is a mobile unit which blends foam concrete from sand, cement, water, foaming agent directly at
the building site. The machine continually mixes all ingredients mechanically, which allows for
fresh concrete with the best properties. The process is controlled and supervised by a control panel.
At least four people are required to run the machine, one machine operator who control machine,
two provides the machine with raw materials and one person to place the foam concrete in a mold.
The machine is easy to service thanks to the well-known component manufacturers which produces
the high-quality components. Cleaning can be done on site with the built-in high-pressure hose.
42113 Builders Hardware Construction Material Equipment Suppliers
Short on time? Let Builders Hardware Construction Material Equipment sellers contact you.
The SD22 is a large horsepower, advanced technology bulldozer with a Cummins 855C engine delivering high torque yet low fuel consumption. An exhaust turbocharger ensures uninterrupted performance at altitudes up to 3200m. Hydraulic drive and control technology deliver reliable performance and easy control.
Performance Parameter
220 HP SD22 Technical specifications:
Blade Type Straight-tilt Angle Semi-U Blade
Min. ground clearance: 405 mm 405 mm 405 mm
Ground pressure: 0.077 MPa 0.077 MPa 0.078 MPa
Min. turning radius: 3.3 m 3.3 m 3.3 m
Gradeability: 30° 30° 30°
Track gauge: 2000 mm 2000 mm 2000 mm
ENGINE Model & type
Cummins NT855-C280S10; In-line,
water cooled 4-cycle,
overhead valve direct injection, turbocharged diesel
Rated power 162 kW
Number of cylinders 6??139.7 x 152.4 mm (bore x stroke)
Piston displacement 14.01 L
Min. fuel consumption 205 g/kW?h
Maximum torque 1030 N?m@1250rpm
POWER
TRANSMISSION
SYSTEM Torque converter 3-element, 1 stage, 1 phase
Transmission
Planetary gear, multi-disc clutch,
hydraulically connected, forced lubrication
Main drive
Spiral bevel gear, splash lubrication,
single-stage speed reduction
Steering clutch
Wet, multi-disc, spring loaded,
hydraulically separated,hydraulic control
Steering brake
Wet, floating, direct on-off hydraulic
inter-linking operation
Final drive
2-stage speed reduction of spur gear,
splash lubrication
TRAVELSPEED Gear 1st 2nd 3rd
Forward 0~3.6 km/h 0~6.5 km/h 0~11.2 km/h
Reverse 0~4.3 km/h 0~7.7 km/h 0~13.2 km/h
UNDERCARRIAGE
SYSTEM Type
Swing type of sprayed beam,
suspended structure of equalizer bar
Carrier rollers 2 each side
Track rollers 6 each side
Track type Assembled, single-grouser
Width of track shoes 560 mm
Pitch 216 mm
HYDRAULIC
SYSTEM Maximum pressure 14 MPa
Pump type Gear pump
Discharge 262 L/min
Bore of working
cylinder no.
120 mm 2
BLADE Blade type Straight-tilt Angle Semi-U-blade
Dozing capacity 6.4 m3 4.7 m3 7.5 m3
Efficiency
(Theoretical value 40 m)
330 m3/h 245 m3/h 365 m3/h
Blade width 3725 mm 4365 mm 3725 mm
Blade height 1315 mm 1055 mm 1374 mm
Maximum drop
below ground
538 mm 535 mm 540 mm
Maximum tilt adjustment >735 mm >500 mm >755 mm
Weight of blade 2830 kg 3254 kg 3419 kg
RIPPER(OPTIONAL)
Maximum digging depth
of 3-shank ripper
666 mm
Maximum lift
above ground
555 mm
Weight of 3-shank ripper 2495 kg
Maximum digging depth
of single ripper
695 mm
Maximum lift
above ground
515 mm
Weight of single ripper 2453 kg
High quality concrete brick machine QT4-16 multifunctional concrete brick machine type is one kind of automatic
brick making machine in our company . It is mainly used in building , bridges , roads . Can make solid brick ,
hollow brick by changing the molds . Very popular in the country whitch need for construction .The machine's
price was also very suitable in this area .
1) Strong structure ,easy in installation and maintain.Ã?Â
2) Adopting advanced world famous brand components in pneumatic parts ,electric parts and operation parts.Ã?Â
3) High pressure double crank to control the die opening and closing.Â
4) Running in a high automatization and intellectualization
5) Apply Famous brand PLC and motors to ensure machine durability.
Material: 304 or 316 stainless steel.
Height above ground: 600mm or your requested height.
Diameter: 219mm or more or less.
Wall thickness: 6mm, or customized thickness.
Control Way: remote control or phone app control.
With led light and reflective tape.
We have our own factory, your design and customize are available.
1.What Is Concrete Canvas?
Concrete Fabric Canvas is a flexible, concrete impregnated fabric that hardens when hydrated to form a thin, durable, water proof and fire resistant concrete layer. It is the original concrete on a roll before hydrate.
2.We produce 6mm,10mm,15mm,20mm these different thickness of concrete canvas
3.2.Characteristics of the Concrete Fabric Canvas when
Concrete Fabric Canvas allows concrete construction without the need for plant or mixing equipment. Simply unroll and position Concrete Canvas, and then just add water (any type of water, including sea water). Concrete Fabric Canvas has no impact on the pH of runoff water. Concrete Fabric Canvas is widely used as a cheaper alternative to conventional concrete.d
Compared to traditional concrete solutions, Concrete Fabric Canvas is faster, easier and� more cost effective to install and has the additional benefit of reducing the environmental impact of concreting works by up to 95%. It is available in bulk and smaller batch rolls.ncrete
3.APPLICATIONS
â? .Ditch Lining
Concrete Fabric Canvas is rapidly becoming the ditch lining material of choice for engineers and contractors around the world.� Concrete Fabric Canvas is typically 10 times faster to install than conventional concrete solutions, with installation speeds of up to 200 m2/hr possible with only a three� man crew for a longitudinal layup.
â?¡.Slope Protection
Concrete Fabric Canvas is increasingly being used as an alternative to non-structural shotcrete to protect slopes from surface erosion caused by weathering, surface run-off and environmental degradation.
In certain applications Concrete Fabric Canvas can be used as structural slope stabilisation by combining it with steel mesh and soils nails (see the Concrete Fabric Canvas User guide� for more details).
â?¢.Bund Lining
Concrete Fabric Canvas can be used for hard armour capping of earth bunds around petrochemical tank farms, munitions depots and flood defences.� Typically installation speeds for bund lining are approximately 800 m2/day with a 6-man crew. Concrete Fabric Canvas Hydro may also be used in this application.
â?£.Vent Walls
Concrete Fabric Canvas can be used as an alternative to brattice cloth, plaster board or concrete block-work to construct blast and vent wall structures for underground mining applications. Trials have shown that Concrete Fabric Canvas typically provides cost savings of over 20% compared to conventional solutions.
â?¤.Outfalls
Concrete Fabric Canvas has been used worldwide as an effective method of preventing surface erosion and scour associated with water run-off from culverts outlets, spillways and over-toppings.
1. Microcomputer-based control text-display screen. NC module input program in dialog mode, convenient operationï¼?
2. With buffering function, and there are wear-proof parts on the joint partï¼?
3. Each step can have 8 bending pipes, and the memory bank can store as many as 9 group of records
4. With slow speed locating function, repeatability precision can be up to+0.1
5. The error information will be displayed on the screen, and operator can eliminate it conveniently
Our products are widely used in various fields: industrial factory, civilian building, warehouse, easy steel building, manufacturing, construction and have features such as nice appearance and durable.
The colored steel tiles produced by this machine look beautiful ,elegant and noble.They are widely used as the roof of garden,factory,hotel,exhibition center and villa,etc.
Introduction
NF Group is a special group for products design,manufacture and sales.
NF Group are the manufacturer and trade body.
NF Group mainly embark on Building Material Projects.
The Machine include Clay Brick Making Machine,Concrete Block Making Machine,Stone Cutting&Polishing Machin , Cement Tile Pressing Machine , Dry Mortar Mixing Machine ,Concrete Mixing Station,Stabilized Soil Mixing Equipment.
NF Group would like to offer you the competitive price and better quanlity.
NF Group will offer the advanced,favorable equipment to the clients.
NF Group would like to develop hand in hand, enjoy cooperation on mutual
benefit and create prosperiy
together.
Other trade Item:
Shoes:
Casual shoes, Sport shoes, Baby shoes, Child shoes, Running shoes, Fashion shoes, skateboarding shoes and Wheel shoes etc.
Stone:
Mable/ Granite slab
Introduction
NF Group is a special group for products design,manufacture and sales.
NF Group are the manufacturer and trade body.
NF Group mainly embark on Building Material Projects.
The Machine include Clay Brick Making Machine,Concrete Block Making Machine,Stone Cutting&Polishing Machin , Cement Tile Pressing Machine , Dry Mortar Mixing Machine ,Concrete Mixing Station,Stabilized Soil Mixing Equipment.
NF Group would like to offer you the competitive price and better quanlity.
NF Group will offer the advanced,favorable equipment to the clients.
NF Group would like to develop hand in hand, enjoy cooperation on mutual
benefit and create prosperiy
together.
Other trade Item:
Shoes:
Casual shoes, Sport shoes, Baby shoes, Child shoes, Running shoes, Fashion shoes, skateboarding shoes and Wheel shoes etc.
Stone:
Mable/ Granite slab
Description of high pressure grouting machine:
WGP800/1200/200PI-D grout station is a combination of mixer, agitator and grout pump in one plant. It is mainly used in highway, railway, hydropower, construction, mining and other ground and underground construction.
High speed vortex mixer ensures mix quickly and evenly. Water, cement or bentonite is quickly mixed into a homogeneous slurry. Then the mixed slurry was delivered to the agitator. Grout pump injects from the mixing drum (storage tank).
This ensures a continuous mixing and grouting operations. The grouting plant is full hydraulic drive with diesel engine. Grouting pressure and displacement is step-less adjustable. Compact size and it is easy to operate. It also takes up a small space.
5. Geotechnical - deep well casing, monitor wells, well sealing and abandonment
6. Acted as a grouting plant in the Pipe Jacking Machine
Wode Heavy Industry Co., Ltd., short name Wodetec, is a manufacturer specialized is R&D, manufacture and sale of grout equipment. Grout Equipment includes: grout plant, grout pump, grout mixer and agitator etc.
Grout equipment is specially designed for continuous cement mixing and grouting in ground and underground engineering, such as highway, railway, hydropower, construction, mining.
Now we have developed full series of grout plant and grout station, pump including piston type, plunger type and hose type. Mixer volume from 200L to 800L, agitator volume from 300L to 1200L, pump flow from 0 to 200L/min and pressure from 0 to 100 bar. Electric power and diesel power are available for customization.
From years of experience Wode Heavy Industry Co., Ltd. has developed its own R&D and technician teams, which supports further development and customized service for clients.
Machine's introduction
1.the main parts:
1) roll forming machine
2)molding press
3)cutting machine
4)PLC computer control
5)hydraulic system.
2.The machine is stable,no noise,no shake.
3.Controlling by computer, PLC display, operation is easy, running is steady and reliable,endurable
4.cutting machine is characterized by stable driving, easy operation.
5.hydraulic system use hydraulic pump, long operating life,no noise.
6.material: galvanized,colored steel or aluminum coil
Machine's Detail:
1,Machine rollers
Roller Material:Roller material :Cr12.
Surface of Roller: Heat treatment HRC58-60.
Forming station: 12 stations.
2,Name: hydraulic pump
Cutting way: Tracking .
Oil pump station: 1set
Motor power of Oil pump station: 7.5kw with cooling system.
3,Name: feeding and leveling device
It used for making the material flat before feeding into the roll forming machine 2 rollers(1 upper and 1 lower)
Domestic famous engines, strong driving force, low fuel consumption, high economic benefits 12F+4R sliding sleeve shift.
4,PLC manufacturer: Siemens
Touch Screen monitor: Siemens
Encoder : Omron (Location: it is after profile formation)
Switch: Omron
Oil hydraulic cylinder: taiwei
Oil pipeline: parkers
Length variation: +/-2mm
Tolerance for hole to hole distance: +/-1mm
If you are interested in our product and want to know more details,please contact me freely: wechat/tel /whatsapp 0086 18522046319
Specifications for Keel Equipment Light gauge steel frame roll forming machine
Manual Un-coiler:
Max Capacity: 5000kgs
Inner diameter of coil:400-600mm
Manual with brake
Leveling Device:
Ensure the material level and straight
The width can be adjusted
Main Forming System:
Width & Height & Thickness of sheet: According to Drawings
Material: GI sheet coil or Colored sheet coil
Motor Power: 5.5 kw forming system
Roller material:Cr12
Surface of Roller: Heat treatment HRC 58-60
Diameter of main shaft: 60mm #45 steel, heat treat modulation
Forming station: 12 stations.
Transmission: by chain and gear
Measuring accuracy: +/- 0.5 mm/M.
Arch middle plate: 30mm thickness.
Output: 8-10 Tons per shift (8 hrs.).
The machine base is assembled and welded by high quality steel.
Cutting way: Tracking
Oil pump station: 1set
Motor power of Oil pump station: 7.5kw with cooling system
Forced air cooling device available.
Cutting mould: 1 sets
Material of blade: CR12 with heat treatment HRC60-62.
Electrical System:
Control system: HMI & PLC control panel
Power: 380V 50Hz (as per local requirement)
Run-out Table:
Frame: A3
Roller type
Quantity: 1 pc
42113 Builders Hardware Construction Material Equipment Suppliers
Short on time? Let Builders Hardware Construction Material Equipment sellers contact you.
