Toronto Automobile Engines Suppliers and Manufacturers

Jet A1 is a� kerosene-type fuel. Jet fuel or aviation turbine fuel is a type of aviation fuel designed for use in aircraft powered by gas-turbine engines. It is colorless to straw-colored in appearance. The most commonly used fuels for commercial aviation are Jet A and Jet A-1, which are produced to a standardized international specification. During the refining process only 8% of the crude oil is made up of Jet fuel.

EN590 Diesel-10PPM Ultra Low Sulfur Diesel (ULSD) is a premium diesel fuel. EN 590 10 ppm is� a type of diesel fuel with a sulfur content of 10 parts per million (ppm).� It\'s a low- emission diesel fuel that\'s ideal for power generators, tower cranes, construction trucks, and excavators with diesel engines.�  It conforms the European standard EN590, with an ultra-low sulfur content of only 10 parts per million (PPM). This type of diesel is known for its environmental benefits and is widely used in modern diesel engines.

D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world, it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2% water and one- half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400.

The full name of Jet Fuel A1 is the aviation Kerosene Colonial Grade 54 Jet Fuel JP 54 Jet fuel designed for use in aircraft powered by gasturbine engines It is clear to strawcolored in appearance The most commonly used fuels for commercial aviation are Jet A and Jet A1 which are produced to a standardized international specification Jet fuel is a mixture of a large number of different hydrocarbons The range of their sizes is restricted by the requirements for the product for example the freezing point or smoke point Kerosenetype jet fuel has a carbon number distribution between about 8 and 16 carbon numbers carbon atoms per molecule wide cut or naphthatype jet fuel including Jet B between about 5 and 15 carbon number Jet A1 is the standard specification fuel used in the rest of the world Jet A1 has a flash point higher than 38C 100 F with an autoignition temperature of 210 C 410 F

Ultralow sulfur diesel ULSD is a cleanerburning diesel fuel that contains a maximum of 15 parts per million ppm of sulfur ULSD contains 97 less sulfur than lowsulfur diesel LSD which typically contains 500 ppm of sulfur The European Union began mandating the reduction of diesel sulfur content in 1993 and the United States started phasing in ULSD requirements for highway vehicles in 2006 It was developed to allow for the use of improved pollution control devices that reduce diesel emissions ULSD can significantly reduce emissions when used in combination with cleanerburning diesel engines and vehicles It may react with strong acids or strong oxidizing agents such as chlorates nitrates and peroxides You should avoid contact with heat sparks fire and oxidizing agents The appearance of ULSD should be clear and bright free from visible sediment and water

Fuel Oil is a fraction obtained from petroleum distillation either as a distillate or a residue Broadly speaking oil is any liquid petroleum product which is burned in a furnace or boiler for the generation of heat or used in an engine for the generation of power except oils having a flash point of approximately 40 C 104 F Oil is made of long hydrocarbon chains particularly alkanes cycloalkanes and aromatics The term Fuel Oil is also used in a stricter sense to refer only to the heaviest commercial fuel that can be obtained from crude oil heavier than gasoline and naphtha Fuel oils are used as fuel for power generation marine bunkers and large industrial heating plants Fuel oil 180 CST also known as Bunker Fuel or Residual Fuel Oil is characterized by its viscosity which is measured in centistokes CST The number 180 indicates the maximum viscosity of the oil at 50 degrees Celsius This specification makes it a relatively thick and viscous fuel compared to lighter fuel oils Both CST 180 and CST 380 fuel oils are considered heavy fuel oils and are commonly used in the shipping industry They are often referred to as bunker fuels and are used in vessels like cargo ships container ships and oil tankers