Toronto Aluminium Containers Suppliers and Manufacturers

Ultralow sulfur diesel ULSD is a cleanerburning diesel fuel that contains a maximum of 15 parts per million ppm of sulfur ULSD contains 97 less sulfur than lowsulfur diesel LSD which typically contains 500 ppm of sulfur The European Union began mandating the reduction of diesel sulfur content in 1993 and the United States started phasing in ULSD requirements for highway vehicles in 2006 It was developed to allow for the use of improved pollution control devices that reduce diesel emissions ULSD can significantly reduce emissions when used in combination with cleanerburning diesel engines and vehicles It may react with strong acids or strong oxidizing agents such as chlorates nitrates and peroxides You should avoid contact with heat sparks fire and oxidizing agents The appearance of ULSD should be clear and bright free from visible sediment and water

Liquefied petroleum gases (LPG): A group of hydrocarbon gases, primarily propane, normal butane, and isobutane, derived from crude oil refining or natural gas processing. These gases may be marketed individually or mixed. Liquefied petroleum gas, also referred to as LPG or LP gas, is� a fuel gas which contains a flammable mixture of hydrocarbon gases, specifically propane, n-butane and isobutane. LPG, any of several liquid mixtures of the volatile hydrocarbonâ??s propene, propane, butene, and butane. It was used as early as 1860 for a portable fuel source, and its production and consumption for both domestic and industrial use have expanded ever since. A typical commercial mixture may also contain ethane and ethylene, as well as a volatile mercaptan, an odorant added as a safety precaution.

D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world, it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2% water and one- half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400.

liquefied natural gas (LNG), natural gas (primarily methane) that has been liquefied for ease of storing and transporting. Liquefied natural gas (LNG) is 600 times smaller than natural gas when the latter is in its gaseous form, and it can be easily shipped overseas. LNG is produced by cooling natural gas below its boiling point, â??162 �°C (â??259 �°F), and is stored in double-walled cryogenic containers at or slightly above atmospheric pressure. It can be converted back to its gaseous form by simply raising the temperature. Natural gas is a hydrocarbon mixture consisting primarily of saturated light paraffins such as methane and ethane, both of which are gaseous under atmospheric conditions. The mixture also may contain other hydrocarbons, such as propane, butane, pentane, and hexane. In natural gas reservoirs even, the heavier hydrocarbons occur for the most part in gaseous form because of the higher pressures. They usually liquefy at the surface (at atmospheric pressure) and are produced separately as natural gas liquids (NGLs), either in field separators or in gas processing plants. Once separated from the gas stream, the NGLs can be further separated into fractions, ranging from the heaviest condensates (hexanes, pentanes, and butanes) through liquefied petroleum gas (LPG; essentially butane and propane) to ethane. This source of light hydrocarbons is especially prominent in the United States, where natural gas processing provides a major portion of the ethane feedstock for olefin manufacture and the LPG for heating and commercial purposes.

Fuel Oil is a fraction obtained from petroleum distillation either as a distillate or a residue Broadly speaking oil is any liquid petroleum product which is burned in a furnace or boiler for the generation of heat or used in an engine for the generation of power except oils having a flash point of approximately 40 C 104 F Oil is made of long hydrocarbon chains particularly alkanes cycloalkanes and aromatics The term Fuel Oil is also used in a stricter sense to refer only to the heaviest commercial fuel that can be obtained from crude oil heavier than gasoline and naphtha Fuel oils are used as fuel for power generation marine bunkers and large industrial heating plants Fuel oil 180 CST also known as Bunker Fuel or Residual Fuel Oil is characterized by its viscosity which is measured in centistokes CST The number 180 indicates the maximum viscosity of the oil at 50 degrees Celsius This specification makes it a relatively thick and viscous fuel compared to lighter fuel oils Both CST 180 and CST 380 fuel oils are considered heavy fuel oils and are commonly used in the shipping industry They are often referred to as bunker fuels and are used in vessels like cargo ships container ships and oil tankers

Material Copper Purity â?¥ 99.95% Shape Rectangular Sheets Dimensions Various sizes available Thickness Typically 5mm - 20mm Width Typically 600mm - 1000mm Length Typically 800mm - 1200mm Weight Typically 50kg - 250kg Color Brownish-red Surface Finish Smooth, clean surface Packaging Bundles or pallets, strapped and wrapped

Jet Fuel A1 and Jet Fuel A FOB Basis for Rotterdam and Houston but mostly Rotterdam. Requirements from buyer - ICPO - Company Profile - Verfiable TSA

Color Black or brown, varying shades Texture Can be smooth, granular, or banded Hardness Soft to hard, depending on coal type Luster Dull to shiny Density Varies depending on coal type, typically around 1.2-1.5 g/cm�³ Porosity Varies, can be porous Composition Mainly composed of carbon, along with hydrogen, sulfur, oxygen, and trace minerals Moisture Content Can range from a few percent to over 30% Volatile Matter Varies, typically 20-45% Fixed Carbon Varies, typically 40-90% Ash Content Varies, typically 3-30% Heating Value (BTU/lb) Varies depending on coal type, typically 8,000-14,000 BTU/lb Heating Value (MJ/kg) Varies depending on coal type, typically 24-33 MJ/kg Combustion Characteristics Burns to release heat, producing carbon dioxide and other gases

Cetane Number 51 min Density at 15�°C 820-845 Kinematic Viscosity 2.0-4.5 at 40 C Sulfur Content 10 max Distillation, 90% Recovered at �°C 370 max Total Contamination 24 max Copper Strip Corrosion, 3 hrs at 50�°C Class 1 max Water Content 200 max Sediment Content 0.05 max Cloud Point -5 max Pour Point -15 max Ash Content 0.01 max

The Middle East's No.1 Classic Shoe Polish for leather shoes helps keep your shoes looking new longer. Belderchin Shoe Polish provides your leather shoes with shine, nourishment and protection while giving them proven long-issuing water protection. Available in different colors including Black, Brown, White, Neutral, etc. When placing an order exceeding one container, you have the exciting opportunity to customize and brand all the products with your unique identity, ensuring a distinctive and personalized touch to your merchandise.