Stainless steel scraps.
HDG, HRC, coils, bars and sheets from DC01 TO DC03.
HR Coil, HR Sheet, CR Coil, CR Sheet, HDG, PPG.
Steel hardware.
Steel scrap.
Copper millberry, steel scrap, wire rod, steel billet, other metals.
Steel bars, steel ropes, scrap used rails, porcelain, glass and polymeric (silicon - rubber) insulators.
Steel scrap.Export
Steel scrap, copper cathodes, iron ore.
Firewoods, steel scrap.
Metals, scrape, steel tubes and profiles.Agents, representative, real estate
Urea n46, sugar, gas oil, jet fuel, rebco, steel billets, chemicals, amino acids for agriculture and many others.
Urea 46 , cement, metals, steels, aluminum, selenium, polipropilen, oil products, sugar.
We can supply you with good quantity of steel slag and mill scale.
Steel barrels.
Tools, power tools, fasteners, household products.
Paper rolls, stainless steel flower hangers & pots.
Press is designed for bending of sheet material. * Operational modes: * Single * Free * Impulse * Body: welded and heat treated steel structure * Hydarulic block * Safety mechanical protection * Photo cell of the working area * Mechanical synchronizer * Mechanized rear limiter * Four-profile tool * Visualizer of carriage travel and rear limiter * El.board with pending control panel Technical information Property Pl 100/31 Pl 100/41 Pl 130/31 Pl 130/41 Maximum bending force(kn) 1000 1000 1300 1300 Reverse stroke force (kn) 160 160 210 210 Carriage stroke Minimum ( mm ) 50 50 50 50 Maxmum ( mm ) 180 180 180 180 Distance from the bending axis to the laterals(mm ) 400 400 400 400 Maximum stroke of the rear stop (mm) 500 500 500 500 Main electric motor power(kw ) 7,5 7,5 11 11 Tank capacity (litres) 160 190 160 190 Overal dimensions : Length(mm) 3800 4800 3800 4800 Width(mm) 2000 2000 2000 2000 Height (mm) 2650 2650 2650 2650 Weight (kg) 9800 11500 12000 14000.
General purpose on copy-milling operations in materials of medium to high tensile strength such as steels up to 1300N/mm, cast iron, aluminum, copper and non-ferrous metals.
# Callipers Measuring range of 0-1000 mm; # With and without fine tunning; # Material – constructional or stainless steel; # Mat chromed scale; # Reading – 0.1 and 0.05 mm. # Special callipers 3-point vernier calliper; # 5-point vernier calliper; # Marking-off vernier calliper; # Weld seam gauge; # Other types. # Vernier depth gauges Measuring range of 0-500 mm; # Reading 0.1 and 0.05 mm; # Material – constructional or stainless steel; # Mat chromed scale. # Micrometers Measuring range of 0-25; 25-50; 50-75; 75-100 mm; # Reading – 0.01 mm; # Measurement reading surface of hard alloys (carbide). Range 0-25 mm. # Coordinate small size tables One-coordinate; # Two-coordinate; # Three-coordinate; # Stroke along the coordinate: 0-25 mm # Measuring stands Type A2 – with magnetic switch at the base; # Type A4 – with cast-iron base and T-shaped groove; # Type B3 – with square-riffled table; # Micrometer holder. # Smooth gauges Plug gauges – one sided; # Plug gauges – two sided; # Snap gauges. # Thread gauges Thread plug calipers – one sides; # Thread plug calipers – two sides; # Thread ring gauges. # Smooth rings Reference rings; # Setting rings Range: 6-150 mm. # Squares and rulers Flat squares; # Squares with base; # Checking rulers; # Templates. # Angle gauges Protractor with lock screw Range 80x120 – 300x500 mm; # Protractor with sliding rod Range 120x240 – 300x500 mm Reading - 1° # Marking-off tools (scribers) Straight scriber – one sided (with knurled handle); # Bended tip scriber – two sided (with knurled handle); # Trammel for tracing and marking with small base; # Vernier caliper with two needles and fine adjustment; # Height gauge with fine adjustment.
