In the rotary klin calcining petroleum coke, the petroleum coke is calcined in a natural way, and the temperature is at about 1350.The lining material hall be of good thermal shock resistance, small changes in the lining line and excellent abrasion excellence. The castable produced by our company adopts dense brown corudum and mullite as the aggregate and fine powder, mixed with 97 sillicon carbide to increase the thermal shock resistance and abrasion resistance, and ensure small changes in the lining line. In the process of use, each castable plate is tightly bonded, without seams and castable peeling. And the petroleum coke is not sticky to the klin wall in the calcining process.
Csa binder is a hydraulic binder based on sulfo-aluminate cement, rather than calcium aluminates which are the basis of calcium aluminate cement (fondu cement) or calcium silicates which are the basis of portland cement. Csa binder is used in formulated products either as a hydraulic binder by itself or with the addition of calcium sulphates or in combination of portland cement. When used as an additive, the following properties can be developed, such as: fast setting time, rapid hardening, the early strength and final strength gains, lower alkalinity (ph value), good expansion value, cracking resistance, corrosion resistance, it can also worked in low temperature. Csa binder can be applied to a wide range of products: Fast setting cement and mortars Rapid repair mortars Fast set tile adhesives Self levelling compounds Self smoothing mortars Non-shrinkage grouts Water stopping mortars Glass fiber reinforced concrete (grc), etc.
The main purpose of corundum crucible is as a container for the analysis and firing of the total production and use of materials or products. Such as the use of coal analysis, metal analysis and melting, chemical raw materials analysis and firing, glass analysis and melting, rare earth and other raw materials and minerals analysis and firing, ceramic and other high-temperature products, firing, System and other industries. Item Alumina Crucible Chemical composition (%) Al2O3 99 R2O 0.2 Fe2O3 0.1 SiO2 0.2 Bulk Density g/cm2 3.80 Apparent porosity % 1 Bending strength Mpa 350 Compressive strength Mpa 12000 Dielectric constant 1MHz 2 Max service Temp 1800
Properties test data unit Thickness 4-10 mm Reflectivity 96-97 % 246weight 256 g/m Water vapour Transmission 0.012 g/m Emissivity 0.03-0.04 coef Corrosion no Thermal Conductivity 0.035 w/m0 Tensile strength (md) 0.77 mpa Apparent density 123 kg/m Tensile strength (td) 1.43 mpa
We, Imperial World Trade Frequently Placed In Ordinary Portland Cement Mortar, Sometimes With A Little Extra Cement Or Some Fireclay Added To Make The Mixture Fireclay Mortar. A Refractory Composition Comprising Of Heat Resistant Binding System And Low Grain Size Refractory Furnaces. Mostly Used For Joining Bricks. Two Types Of Settings: Air And Heat Setting Mortar The Mortar Hardens At A Heat Above Room Temperature. The Problem With Using Regular Mortar Is That Portland Cement Can't Take The Heat. Curiously, Cement Retains Its Energy Up To Reasonably High Temperatures But Declines As It Cools Down Through About 600�° F. Ultimately All That Is Left Of The Mortar Is The Sand And Fireclay, With No Cement Binder. The Mortar Has No Strength And Easily Falls Out Of The Joints, Especially If They Are Wide. Refractory Mortar, On The Opposite Side, Is Performed With High-Temperature Cement And Carefully Selected Aggregates That Don't Expand And Tear The Mortar Apart When Heated. The International Residential Code (IRC) And International Building Code (IBC), Which Were Recently Adopted In Approximately All States And Require That Fireboxes, Smoke Chambers, And Flue Liners Be Laid With Refractory Mortar.
Refractory temperature: 1800 () Compressive strength: strong (Mpa) Specifications: According to customer requirements (mm) Molten copper furnace refractory castable is suitable for oil refinery catalytic cracking equipment cyclone separator, double slide valve, riser, dilute phase tube, foot, etc., other chemical equipment, such as ammonia pouring in a conversion furnace lining, two paragraphs.
Refractory temperature: 1800 () Compressive strength: strong (mpa) Specifications: according to customer requirements (mm) Gongyi taurus refractory material factory is a professional refractory materials manufacturers and refractory materials suppliers, mainly supply refractory bricks, unshaped refractories, silicon carbide refractory castable, castable refractory cement, pouring material, castable refractory concrete, silica ramming mass etc. Series of refractory materials products, sincerely welcome everyone to visit.
No need to use Plaster of Paris, Chalk Powder or Primer before applying paint Apply on almost all interior surfaces whether new or old
All type of Concrete Admixture. Official Head of Bangladesh, MARKCHEM Construction, Bangladesh Division located at Dhaka. Brand: MARKCHEM, India. Other products like BASF Bangladesh, FlowCrete Malaysia, Gerflor French, Fosroc, Sika, Pidilite etc.
BuildWell Quickbond is a admixture of sand, cement and superior quality polymers. It is a bonding agent that enables quick preparation of ceiling and RCC wall surface. Also offers the dual benefits of mechanical and chemical bonding, which eliminates the labor – intensive hacking and reduces debonding losses. Features : - Excellent bonding. - No hacking is required on RCC wall. - Hence prevention of microcracking and saving of labor cost. - Strong chemical and mechanical bond - Easy to use. - Works good for Gypsum plaster as well for cement sand plaster Benefits : - Can be easily applied by brush. - Reduces hacking. - Time saving. - Less rebound loss while plastering. - It is water soluble product hence no solvent odour. - Fast drying. - Improves bonding strength between RCC wall and Plaster.
Step N Riser ( staircase) is most important elements of any structure. The use of steps is very high and hence ceramic material can't be used. Where granite and marble have the natural advantage that as much as its getting in used, the shining will not get dull but increasing. For the projects, we are providing the ready to use steps and riser. It will be available in customize sizing as per requirements. The molding and anti slipper lines also getting done. So just ready to use Step n Riser. ( Staircase). Its will be be done with all granite and marbles.
Wall Putty is completely cement based putty which is white in color. Its use is better for the exterior as well as interior walls of buildings. The white colored cement-based putty binds very strongly with base plaster in such conditions as well when the surface is damp and it forms a good and protective base. The pores (fine one) on ceiling and walls can be easily fills up and gives you a fine even and very smooth and dry surface which is best for painting. Wall putty gives an effective protection against flaking; so it assures you good even, looking smooth walls of your home for so many years. Features / Advantages: It is white cement based and skim coated. For application of paint it gives smooth and water resistant surface. It has as excellent adhesion. It causes no peel off because of seepage. It gives excellent finish, increases the durability of paint, and causes less consumption of paint. No need of primer. No kind of curing is required. Areas of application: Application can easily applied on plastered surface. It gives fine finish and it is very useful for Inner and Outer walls. Surface Preparation and Application Before applying wall putty makes sure that the surface is free from dust or not, if not make it dust free. Also make sure that it is free from any type of fungus, greases, bitumen, and any kind of release agents, moss, paints, oils, loose particles or any kind of coating. Make sure that the surface should be free from all the above mentioned impurities otherwise it affects the workability of wall putty. Before applying make sure that the surface where the putty is supposed to be applied should be pre-wetted. This will helps you to provide a very strong bond with the substrate. Its better to apply at least two coats of Addage Wall Putty on plastered surface of wall (Each coat should be Max 1.5 mm of total thickness). Coverage The Addage Wall Putty covers almost more surface area that is exceeding to 9-10 Sq. ft. /kg. In two coats on new plastered wall.
4-0mm powder size 6-0 Mass Patch Sand Size 8-5 mm and 11-7 mm Size 16-9 mm and 12-12 mm Size 17-35 mm and 40-23 mm
- (BRC) Welded Wire Mesh - Design/Engineering Wire Mesh - Deformed Bar / Round Bar - Common Nails - Coil Nails - Hard Drawn Round / Ribbed Wire - Chain Link Fencing - Barbed Wire - Fencing Mesh - Masonry Brick ( 100mm / 125mm / 150mm / 200 mm ) Autoclaved Aerated Concrete for building materials. - SEA SAND / RIVER SAND from Malaysia All the product above comes with test certificates whichever requires.
Rock Boulders : Middle East / India / China 50kg to 2000kg and above
Nameï¼?Construction Material Plastic Formwork Applicationï¼?Concrete Construction Colorï¼?White Black Typeï¼?Waterproof Plastic Template Wall Formwork Sizeï¼?1220mm*2440mm Certificateï¼?SGS Thickness:16mm Usage:Concrete Construction Support Material:PP plastic
Name- Building PP Plastic Template ApplicationConcrete Construction ColorWhite Black TypeWaterproof Plastic Template Wall Formwork Size1220mm*2440mm CertificateSGS Thickness:15mm Usage:Concrete Construction Support Material:PP plastic
FASTEN is a geotextile material (Polymeric Strip, Geostrip) used for reinforced earth retaining wall panel (MSE wall panel) production in civil engineering works such as road, harbor and bridge works. It restrains the lateral displacement of soil and increases the durability of soil and stability of its shape, thus increasing the workability, stability and cost down in civil engineering works. Based on accumulated R&D, it will help many kinds of development works with its low cost and stable work performance. Our factory is located in South Korea and has been produced this item over 20 years. FASTEN is economical. As the land can be effectively used and the wall can be designed and constructed according to the wall structure in the site, the construction cost can be reduced. FASTEN is easy to work. As the materials are supplied in the form of finished products, and the wall can be constructed by simply assembling the products and constructing the foundation, the work period can be shortened and the work can be easily finished. FASTEN is excellent for mechanical stability. As the product is resistant to erosion and corrosion by bacteria or organic microbe, it is eco-friendly and durable materials. In the forming of soil structure, it constrains the lateral displacement of soil and induces the apparent adhesiveness that it increases the tension strength and maintains the stability against earthquake and vibration. For more information, you can simply visit our website and contact us by e-mail.
FASTEN is a geotextile material (Polymeric Strip, Geostrip) used for reinforced earth retaining wall panel (MSE wall panel) production in civil engineering works such as road, harbor and bridge works. It restrains the lateral displacement of soil and increases the durability of soil and stability of its shape, thus increasing the workability, stability and cost down in civil engineering works. Based on accumulated R&D, it will help many kinds of development works with its low cost and stable work performance. Our factory is located in South Korea and has been produced this item over 20 years. FASTEN is economical. As the land can be effectively used and the wall can be designed and constructed according to the wall structure in the site, the construction cost can be reduced. FASTEN is easy to work. As the materials are supplied in the form of finished products, and the wall can be constructed by simply assembling the products and constructing the foundation, the work period can be shortened and the work can be easily finished. FASTEN is excellent for mechanical stability. As the product is resistant to erosion and corrosion by bacteria or organic microbe, it is eco-friendly and durable materials. In the forming of soil structure, it constrains the lateral displacement of soil and induces the apparent adhesiveness that it increases the tension strength and maintains the stability against earthquake and vibration. For more information, you can simply visit our website and contact us by e-mail.
FASTEN is a geotextile material (Polymeric Strip, Geostrip) used for reinforced earth retaining wall panel (MSE wall panel) production in civil engineering works such as road, harbor and bridge works. It restrains the lateral displacement of soil and increases the durability of soil and stability of its shape, thus increasing the workability, stability and cost down in civil engineering works. Based on accumulated R&D, it will help many kinds of development works with its low cost and stable work performance. Our factory is located in South Korea and has been produced this item over 20 years. FASTEN is economical. As the land can be effectively used and the wall can be designed and constructed according to the wall structure in the site, the construction cost can be reduced. FASTEN is easy to work. As the materials are supplied in the form of finished products, and the wall can be constructed by simply assembling the products and constructing the foundation, the work period can be shortened and the work can be easily finished. FASTEN is excellent for mechanical stability. As the product is resistant to erosion and corrosion by bacteria or organic microbe, it is eco-friendly and durable materials. In the forming of soil structure, it constrains the lateral displacement of soil and induces the apparent adhesiveness that it increases the tension strength and maintains the stability against earthquake and vibration.
