Yingfan Polypropylene (PP) biaxial geogrid is a high-performance soil reinforcement product to resist elongation when subjected to heavy loads for long periods of time. By reducing the cost of construction, the biaxial geogrid can meet project requirements and offer full technical support. (Please note that the price is not stable due to raw material (influenced by oil price) and exchange rate.) Product Features - Stabilization - Reinforcement - Durability and high resistance Usage Areas - Municipal roads, Railway ballast, highways, and airports - Industrial shipping yards - Parking lots, steep slopes - Retaining walls, bridge abutments... and more Standard Size - 3/4/6 m width - 50-100 m length - Upon request
1.Qtz50(pt5010) topless tower crane 2. Type: fixed and external climbing 3. Jib lengthï50m 4. Tip load:1.0t 5. Max.Laod: 5t Emma1109(at)foxmail(dot)com Skype:xiaopiao119
Concrete Road Pipe Making Machine Overview: Suspension roller concrete pipe making machines are used for producing reinforced concrete pipes and Pre-stressed concrete pipe. This kind of machine is capable to make pipes with diameter from 300-2000mm and with length from 1-4meters. We can design flat end, socket & spigot end, male & female end. All the concrete pipes are widely used in urban drainage, agricultural field irrigation, road culvert and deep water well. Working Principle: This XG series Concrete tube machine is with simple structure. The suspended roller passes through the tube mould. Driving by the motor, the transmission shaft will drive the roller rotating at a regulated speed. Because of the friction force between the roller and stop ring at the ends of mould, the pipe mould will be drove rotating at the same direction as the roller. By manual feeding concrete or conveying machine, the concrete mixture into the mould will be adhere to the inner wall of mould, and become solid. Owing to the function of the Roller Compressing Force and Centrifugal Force, and then form a standard quality pipe. Features: 1. Wide Production Range: Inner Diameter form 200-2500mm, length 1-4meter. 2. Three kind of tube end joint: Flat end, Male& Female end, Spigot&Socket end. 3. High efficiency: Every pipe just need 3-5 minutes with high speed roller rotation. 4. Environment Friendly: Using dry casting concrete,no polluted slurry discharge. 5. Lower noise.
1. Model: QTZ40(TC4208) Topkit Tower Crane 2. Type: fixed and external climbing 3. jib lengthï¼?42m 4. tip loadï¼?0.8t 5. max.laod: 4t 6.freestanding height: 29m emma1109(at)foxmail(dot)com skype:xiaopiao119
All types of construction hardware available. Stainless steel, brass, aluminium, etc.
The snow removing equipment is the necessary equipment of snow cleaning for farm,orchard, schools, parks, squares, residential areas, garden, lanes sideways, bridges and other key securing sites and widely used in snow winter. This equipment could improve the efficiency of snow removal, reduce labor intensity, and ensure pepole going out more safety and convenient. 1).The road sweeper can be matched to tractor,wheel loader,forklift, 2).powered by hydraulic output of these machinery,only tractor could be driven by PTO. 3).PP with steel wires brushes. 4).Working width from 1200 to 2500mm 5).Suitable for cleaning road,street,floor and other flat.
*The engine adopts famous brand engine, 100% inspection before delivery. *The Snow Cleaning Machine adopts full metal jacket design,after oxidation spray,anti-corrosion rust proof,long service life. *Double LED lamp of operation panel, greatly improving the workers efficiency and safety at night and early morning. *The Snow Cleaning Machine uses monolithic auger design, low cost of vulnerability consumption and easy replacement. *The Snow Cleaning Machine has the advantages of fashion appearance,mult functions, light and flexibility,simple operation.
Construction Equipment
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
96A glass furnace silica brick, silica brick, silica sand, quartz sand, silica powder, high alumina brick, fire-clay brick, magnesia brick.96A glass furnace silica brick, silica brick, silica sand, quartz sand, silica powder, high alumina brick, fire-clay brick, magnesia brick
Jute (including kenaf) was an important foreign exchange earner for the producing countries during '60s. Even during the '70s, jute was an important commodity for most of the producing countries. However, during the '80s, bulk handling techniques and synthetic substitutes entered the market and jute started losing its predominant position in the market.
LLDPE smooth geomembrane owns much of the characteristics of High-Density geomembranes (HDPE), such as long life span, and high elongation, but LLDPE Geomembrane liners are extremely flexible due to the raw material. Meanwhile, the LLDPE geomembrane's high carbon black content provides excellent protection from UV rays. The geomembrane liners can be widely used in various applications that require flexibility, elongation, and chemical resistance. (Please note that the price is not stable due to raw material (influenced by oil price) and exchange rate.) Product Features - Long life span · Resistance to cracking - Resistant to aging and corrosion - Resistant to UV radiation(sunlight) - Retain their mechanical and physical properties - High performance in the intense stresses of weather Usage Areas - Fuel tank storage facilities & chemical holding basin - Aquaculture ponds, canals, and water retaining - Chemical reaction pond & sedimentation basin - Environmental Remediation Capping - Industrial & Municipal Landfill - Semi-liquid manure and slurry... and more Available Colors - Black - Green - Blue - Upon request Standard Size - 6-8 m width - 80-105 m length - 0.2-3.0 mm thickness - Upon request
Textured geomembrane owns many characteristics as High-Density geomembranes(HDPE)do, for example, a long life span, high elongation, and a high degree of chemical resistance. Moreover, this geomembrane is flexible. (Please note that the price is not stable due to raw material (influenced by oil price) and exchange rate.) Product Features - Long life span - Superior flexibility - Resistance to cracking - Resistant to aging and corrosion - Resistant to UV radiation(sunlight) - Retain their mechanical and physical properties - High performance in the intense stresses of weather Usage Areas - Canals and water retaining - Landfill caps - Mining - Wastewater treatment...and more Available Colors - Black - Green - Blue - Upon request Standard Size - 6-8 m width - 80-105 m length - 0.75-3.0 mm thickness - Upon request
Enhance Your Perimeter: Exploring Top-Quality Chain Link Fence Fittings by Him Overseas In the realm of security and aesthetics, Chain Link Fence Fittings play a pivotal role in fortifying your perimeters. At Him Overseas, we take pride in presenting an extensive array of these fittings, meticulously designed to elevate your fencing solutions. Let's delve into the world of durable, high-grade fittings that redefine security standards. Unveiling the Arsenal: Him Overseas' Chain Link Fence Fittings Selection 1. Fence Bands 2. Fence Wheel Carriers 3. Fence Clamps 4. Fence Collars 5. Fence Gate Rollers 6. Fence Hardware Fittings 7. Fence Metal Ornamental Fittings The Him Overseas Advantage As an ISO 9001:2008 certified organization, Him Overseas is committed to delivering Chain Link Fence Fittings of optimum quality. We understand the diverse needs of our clients and manufacture our fittings using high-grade stainless steel and other metals. The result? Chain Link Fence Fittings that boast superior physical and mechanical properties, ensuring resilience in adverse environments. Your Trusted Partner in Fencing Solutions Him Overseas stands as a beacon in the industry, recognized as one of the leading Manufacturers and Exporters of Chain Link Fence Fittings. We take pride in offering the largest supply of fittings, catering to all customers with affordability as a core principle.
Wooden Fencing Species : Keruing , Kapur/Kamper , Bangkirai , Meranti Sizes : 1800 x 1800mm
Product name: Bamboo Fence Color: Natural Orgin of place: Vietnam Thickness (mm): 3-5 Diameter (mm): 14/16/18/20/24/32/38/45/50 Process: Cut in proper length, steam at 1000 degree for 20 mins, clean well, dry at 150 degreee until the moisture reach 15%, sort into bundles. Packing: 50pcs/ bundle
Product name: Bamboo Fence Color: Natural Orgin of place: Vietnam Thickness (mm): 3-5 Diameter (mm): 14/16/18/20/24/32/38/45/50 Process: Cut in proper length, steam at 1000 degree for 20 mins, clean well, dry at 150 degreee until the moisture reach 15%, sort into bundles. Packing: 50pcs/ bundle
Geo Textile Netting made of Natural Coco Fiber in White or Brown Coir. (Machine or Hand woven). Used to control Soil Erosion, at work sites, road construction areas, river banks etc.. as a protective measure/Mesh. Can be used as backing for hydro seed spraying. Specifications Mesh Hole size : 20mm x 20mm or 30mm x 30mm or (As per buyer’s requirement for any pattern and size) Supplied in rolls any length and any width (up to 2 meters of maximum width).
as 3D scale model maker and architectural model making firm, topped in list of Model Making Companies. Our Expertise in Product and Miniature Model Making earned us great prestige as best scale model makers , product and architectural model makers, industrial and engineering model builders, Building Model makers. We are based in and serving all over the world.
