Easy To Apply
Single Pack
Superior Durability
Excellent Gloss Retention
SCOPE
USES
Kisomin Aluminium Paint is a modified Synthetic Resin based enamel.
It provides high Light fastner and brightness with excellent orientation
finish. it has good adhesion on interior or Exterior surfaces.
Recommended as a decorative finish coat & can be applied on
surfaces like Grill, Windows, Cabinets & wide range Metal Structures.
VISCOSITY FOR APPLICATION
* For Brushing 40"-45" at 30C
* For Spraying 18" 20" at 30C
* For Roller 55"-60" at 30C
SURFACE PREPARATION
APPLICATION
BRUSH
CONVENTIONAL SPRAY
NOTES :
HEALTH & SAFETY
Steel : Sand the surface with coarse Sand / water paper according to the type of surfaces to remove rust, dust & other foreign particles. System of
Coating should be selected depending upon the type of substrate. Wipe to clean the surface. Apply single coat primer & allow to dry. Re sand the
surface with Sand paper & wipe to clean. Apply 2nd Coat of primer & allow drying for overnight. Before application of paint, thin down to achieve
desired viscosity & filter through white cloth. Apply Kisomin Paint to finish.
Stir the base thoroughly and then mix to uniform consistency.
Apply by diluted material, where viscosity has to be ensure 40-45 sec by f.c. B4
Add Kisomin thinner to adjust viscosity depending on spray condition. Use any standard equipment at an atomizing pressure of 3.5-4.5 kg/cm.
1. Use off the mixed paint .
2. Do not apply when temperature falls below 10c or rises above 50c and when relative humidity rises above 90%. Do not apply during rain, fog or mist
3. Brushes and spray equipment should be cleaned with Thinner,
4. Special care to be taken to close immediately the partly used Diluted Material.
Please refer to the separate Material Safety Data Sheet available with detailed information
HI - Performance Syn. Enamel Paint
Superior Durability Color Pigment System
Easy To Apply By Brush , Roller And Spray
PRODUCT PARAMETERS
1. Type : Single Pack
2. Composite : Modified Oil Based Resin with Finest Bright
Pigments, Hydrocarbon solvent and addives
3. Use Recommended Thinner to make
Applicaon Viscosity
4. Applicaon Tools : Brushing, Spraying or
Roller
5. Flash off = 30 Minutes
6. Drying Time :
Surface Dry : 4 Hours
Hard Dry : Overnight
7. Curing Time : 72 hours
8. Over coang Interval : MIN : Overnight
MAX : 5 Days
9. Color : Assorted Shades
. Finish :
10 Smooth Finish
11 Thinner / Cleaner KISOMIN THINNER
12. Shelf Life: Up to 12 Months as long as the sealed containers
are kept under cover in a dry place under normal
temperature.
SCOPE
USES
Kisomin durable synthec enamel are long lasng & solvent based
paint used for wide range of surface.
Recommended as a decorave finish coat & can be applied on
surfaces like Metal, Cement Brickwork, Asbestos Grills and Wooden
surfaces like doors, Windows, Cabinets & wide range of furniture
PERFORMANCE PROPERTY
Chemical Resistance
A Exposures Splash & Mild Fumes/Outdoor
Spillage Resistance
cid + +
Alkalis + +
Solvent NA NA
Salt ++ ++
Water +++ +++
Flexibility +++
Adhesion +++
Excellent : +++
Very Good : ++
Good : +
SURFACE PREPARATION
APPLICATION
BRUSH
CONVENTIONAL SPRAY
NOTES :
HEALTH & SAFETY
Steel : Sand the surface with coarse Sand / water paper according to the type of surfaces to remove rust, dust & other foreign parcles. System of
Coang should be selected depending upon the type of substrate. Wipe to clean the surface. Apply single coat primer & allow to dry. Re sand the
surface with Sand paper & wipe to clean. Apply 2nd Coat of primer & allow drying for overnight. Before applicaon of paint, thin down to achieve
desired viscosity & filter through white cloth. Apply Kisomin Paint to finish.
Sr the base thoroughly and then mix to uniform consistency.
Apply without thinning
Add Kisomin thinner to adjust viscosity depending on spray condion. Use any standard equipment at an atomizing pressure of 3.5-4.5 kg/cm�².
1. Use off the mixed paint .
2. Do not apply when temperature falls below 10 C or rises above 50�°c and when relave humidity rises above 90%. Do not apply during rain, fog or mist
3. Brushes and spray equipment should be cleaned with Thinner,
4. Special care to be taken to close immediately the partly used Diluted Material.
Please refer to the separate Material Safety Data Sheet available with detailed information
we are supplier for Yamaha Motors, Daimler Trucks,Philips, Royal Enfield Motors, fermetor Auto Door for Lift our customer List Exhaustive,
we make tool and die and produce your component
450ML 24PCS/CTN 363G GROSS WEIGHT OEM is welcome
Near Qingdao port, rich experiences on exporting dangerous goods
Shandong Saigao New Materials Co.,Ltd, located in Linyi city,Shandong province
5 production lines
90000 covering areas
100 workers
6 engineers
Special Structual Spray-coat material for running track surface installation ,consume 1.20-1.25KG/m2 to achive 3mm
Spray-coat Running track PU1:2 Spray-coat track material is an pigmented and solvent free thixotropic, two component polyurethane material with expanding form, strong resistance ,elastic properties, should be mix two component on project site,
Spray-coat Running tack PU1:2 Spray-coat track material is easy to apply ,it shows excellent resistance to moisture during the curing phase and a good curing behavior even at low temperature
Wl-156 is an anionic hydroxylated styrene acrylic copolymer emulsion. It is recommended to use with amino resins for baking coatings, which requires high gloss, good hardness and outstanding solvent resistance. Biocide: CMIT/MIT 3:1 49ppm, and MIT 240ppm.
Properties
1. Excellent resistance to boiling water
2. High gloss, high hardness
3. Excellent solvent resistance
4. Excellent recoatabilit
Note:Be sure to adjust the pH of WL-156 over 7 with the pH adjustment in use.
Characteristic data* Property Value Unit Method
Appearance Translucent to milky white
Weight Solids 47�±1 %
pH 3.5-5.5 GB 6920-1986
Viscosity 10-1000 mPs Brookfield,LV,62#,30rpm,25C
MFFT 40-42 C GB/T 9267-2008
OH content 1.3 % Calculated on solid resin
Density 1.04 g/cm3 GB/T 4472-2011
Alkyd resins represent, both historically and commercially, the class of chemical compounds used in the field of paints and stains. Their chemical structure is a continuous and waterproof film which can protect surfaces from multiple strenuous agents conducting an anti-corrosive. The commercial paints based on these resins, the molecules of the structure, in particular, create strong structural interactions involving the formation of films able to cover any type of surface by protecting against aging, weather and wear. the paints made from alkyd resins have been among the first to be used in the construction industry, in particular in the production of exterior paints and enamels, and in the production of products for the treatment of surfaces exposed to particularly arduous conditions, for example various ferrous metal substrates such as structural steel, railings, equipment and machinery.
We offers alkyd resins that have achieved high functionality through modification with other resins such as acrylics, urethanes, epoxies.
Features:
Good storage stability, no ease to hydrolyze;
Environment friendly product, VOC of less than 7%;
Fast dry, and excellent gloss;
unnecessary to add drier during paint preparation;
Excellent shear stability, and can directly use for pigment paste grinding;
Excellent anti-corrosivity, and good initial water resistance;
The finished product paint has good versatility and good in-can appearance, and can replace oil based alkyd anti-rust paint, alkyd ready mixed paint, alkydenamel, etc
SE 6651 K is an hydroxyl functional acrylic resin that, when combined with appropriate aliphatic polyisocyanates, provides excellent durability and outstanding gloss retention. It should be used in solid color paints and clearcoats for vehicle refinishing and in industrial topcoats. Se 6651K is used in combination with aliphatic isocyanates it exhibits good exterior durability, good build and gloss, high end hardness and good adhesion results on metallic base coats.
1. Features
High gloss, good levelling property, high hardness, excellent chemical resistance and pigment dispersity
2. Applications
PU top coat, automotive refinishing paint, colored paint
The biggest difference between thermoplastic spraying road marking paint and common thermoplastic screeding coating material is that the viscosity and density of the coating and the construction process are different. During the construction, the molten paint is applied to the road surface by centrifugal force to form a road marking paint.
The thermoplastic spraying road marking is thinner, the construction is fast and efficient, and the durability is close to the ordinary hot-melt coating line, which makes it economically more advantageous than the ordinary hot-melt type.
Generally applicable to the old road over coating and road sections with very rough road structure.
EPOXY THINNER is a mixture of suitable solvents intended for thin epoxy products. It can be used for cleaning tools, dirty with epoxy products. Epoxy thinner is a balanced solvent blend designed to thin epoxy paints. It can be used to control film thickness per coat, reduce orange peel, improve wetting of topcoat to primer and reduce dry spray or dry spots in painted areas.
Excellent foam control.
Improve wetting, leveling and flow.
Resist Moisture.
Impart slip and gloss.
Help prevent pigment seperation.
Suitable for use in industrial wood coatings, interior and exterior paints, inks and overprint varnishes.
Introduction:
Control the actual thickness of dry film or wet film by the precise test of coating.
The coating with excellent consistency and repeatability is required when
doing the coating opacity, wear-resistance, sag-resistance performance and other.
Technical Specification:
High grade stainless steel
C- Sharp design
Film Width: 80 mm
Overall Length: 90 mm
Order Information:
BEVS 1802/ 1: Two Sided Applicator 80 mm film width gap size 25&50um
BEVS 1802/ 2: Two Sided Applicator 80 mm film width gap size 75&100um
BEVS 1802/ 3: Two Sided Applicator 80 mm film width gap size 150&200um
BEVS 1802/4: Two Sided Applicator 80 mm film width gap size 300&400um
Introduction:
BEVS bar applicator is a fully new generation technology against traditional wire bar, ideal for the application of inks and coatings onto flexible materials such as paper, card, textiles, leather, automatic film applicator and etc.
The wet film thickness applied is controlled by the area of the groove between the coils of bar,the minimum thickness can be reach to 6μm.
Feature:
Not peel off
Easy to clean
Apply to 6μm
Technical Specification:
Excellent stainless steel bar : diaÃ?10mm
Total bar lengthï¼?240 or 400mm
5639 Paints Coatings Suppliers
Short on time? Let Paints Coatings sellers contact you.
