Opticombine Industrial Ethernet Switch, 1 x 10/100/1000M Base A network switch is networking hardware that connects devices on a computer network by using packet switching to receive and forward data to the destination device. Feature 1. High quality optoelectronic modules provide good optical and electrical characteristics. 2. Ensures reliable data transmission and long working life. 3. Supports full duplex or half duplex mode with automatic negotiation capability. 4. Automatic cross recognition of network port support. 5. In line with carrier level operation standard, the average fault free operation is more than 50 thousand hours. 6. Working power supply: DC 10-52V provides anti connection protection. 7. Uses SC optical fiber interface (optional ST, FC, SFP interface) 8. Lightning surge protection (power):5000A (8/20 s)
Definition of 400G QSFP-DD Transceivers QSFP-DD stands for Quad Small Form Factor Pluggable Double Density. The 400G QSFP-DD Transceiver follows the same port densities system as the QSFP and QSFP28, but the QSFP-DD will support eight lanes instead of four lanes for the QSFP and QSFP28, which double the density. Each of the eight lanes will operate a data rate up to 50Gb/s providing a 400Gb/s data speed and increasing the capacity of the QSFP28 by four. The 400G QSFP-DD MSA published that the size of the optical transceivers enables to put 36 ports in one switch slot, accumulating 14.4 Tbp/s in one slot. Multi-mode Transceivers Multi-mode transceivers are the low cost transceivers. QSFP-DD SR8 use more expensive non-standard MPO connectors which cancel out some of the cost savings of the multi-mode transceiver. 400G QSFP-DD SR8 The 400G QSFP-DD SR8 transceiver supports connections of up to 100 meters over multi-mode fiber and uses MPO connectors. The wavelength is 850nm. It is compliant with the QSFP-DD MSA. Single-mode Transceivers Single-Mode transceivers are more expensive than multi-mode transceivers but they allow to reach longer distance. 400G QSFP-DD DR4 The 400G QSFP-DD DR4 transceiver supports connections of up to 500 meters over single-mode fiber and uses MPO connector. The wavelengths is 1310nm. It is compliant with the QSFP-DD MSA. 400G QSFP-DD DR4+ The 400G QSFP-DD DR4+ supports connections of up to 2 kilometers over single-mode fiber and uses MPO connector. The wavelengths is 1310nm. It is compliant with the QSFP-DD MSA. 400G QSFP-DD LR4 The 400G QSFP-DD LR4 transceiver supports connections of up to 10 kilometers over single-mode fiber and uses LC connectors. The wavelengths are 1296 to 1309nm. It is compliant with the QSFP-DD MSA. 400G QSFP-DD Loopback The 400G QSFP-DD Loopback is a cost effective and high quality solutions to test 400G QSFP-DD transceivers ports.
Smart Home Gateway Convexa-S is a unique smart home gateway with beamforming Wi-Fi, Zigbee* and Bluetooth* that can connect all your IoT devices together. More wireless protocols will be added. 400Mbps (2.4G) + 867Mbps (5G) Combined Wi-Fi Speed Built-in Bluetooth or Zigbee Module * 3 x Gigabit Ports Supports MU-MIMO
Keep Snoopers Off Your Wi-Fi Network Keep your Internet connection private with multiple VPN protocols support. GL.iNet Slate provides the best encryption and authentication with OpenVPN. Meanwhile, WireGuard�® gives the privacy-minded users a fast and simple VPN that utilizes state-of-the-art cryptography. Max. 300Mbps (2.4G) + 433Mbps (5G) WiFi Speed 128GB Max MicroSD 3 x Gigabit Ports
4G LTE Smart Router Spitz is a 3G/4G dual-band wireless router, widely used for smart home and IoT area. Running OpenWRT OS, you can compile your own firmware to fit for different application scenarios. It has built-in mini PCIe 3G/4G module to support different operators and can be used all over the world. 300Mbps (2.4G) + 433Mbps (5G) Combined Wi-Fi Speed 128GB MicroSD Capacity PCIe 4G LTE Modem Built-in Bluetooth or Zigbee Module
4G LTE Industrial Wireless Gateway Collie is a compact and cost-effective industrial 4G router. Equipped with the external full-band 4G antennas, the aluminum alloy shell and the hardware watchdog, the mobile router ensures stable LTE connectivity in harsh and hazardous environments. Collie can also serve as a smart industrial Internet gateway with the functions of RS485 interface and the optional IoT module for a range of IoT applications including vending machines, charging piles, smart agriculture, metering, and more. Max.150 Mbps Wi-Fi Speed Built-in 4G Module Built-in Watchdog Built-in Bluetooth or Zigbee Module (Optional)
Industrial 4G IoT Gateway Amarok is a powerful and stable operation, a cost-effective product designed to meet the needs of industrial users through 4G/3G signal wireless internet access. Because of its open source platform-based features, it can also be used as an integrated platform for extension such as developers, makers, and IoT integration development. 300Mbps (2.4G) + 867Mbps (5G) Combined Wi-Fi Speed 5 x Gigabit Ports PCIe 4G LTE Modem 128GB Max MicroSD Supports MU-MIMO
Mini Wireless Router Our GL-MT300N-V2 is upgraded to new chip MT7628NN, and the RAM is enhanced from 64MB to 128MB. Also, the MTK driver helps to improve Wi-Fi connections, coupled with faster OpenVPN encryption. 4 GPIOs are included for DIY fun. From this, GL-MT300N-V2 is your best pal for travel. Max. 300Mbps Wi-Fi Speed 1 x 2.0 USB Port 1 x Switch Button 2 x Ethernet Ports
A9500N is one of the smallest NB-IoT modules in LCC castellation packaging with the compact size of 24.0 Ã?? 26.0 Ã?? 2.3mm, ultra low power consumption and extended temperature range. Designed for use in NB-IoT network, A9500N enables connect to the Internet at DL and UL data speed up to 200kbps. In the area where NB-IoT service are not available, A9500N still enables reliable and secure data connect over EGPRS network. To save space on the application platform, A9500N comes as an extremely slim and compact module. This makes it ideally suited for a broad range of mobile computing devices, and particularly offers easy integration with AMI, Security, Intelligent Buildings and other M2M application. General features * NB-IoT Tri-bandB3/B5/B8 * EGPRS Dual-bandB5/B8 * Control via AT commands(GSM07.05,GSM07.07,V.25TER,GPRS, and enhanced AT commands) * Supply voltage range 3.1V-4.2V * Low Power consumption - eDRX mode:
The SIM7000E is Tri-Band LTE-FDD and Dual-Band GPRS/EDGE module solution in a SMT type which supports LTE CAT-M1(eMTC) and NB-IoT up to 375kbps data transfer. It has strong extension capability with rich interfaces including UART, USB2.0, GPIO etc. The module provides much flexibility and ease of integration for customer's application. The package of SIM7000E is compatible with SIM900 and SIM800F. AT commands of SIM7000E are mostly compatible with SIM800F. This also maximizes the investments of customers, and enables a short time-to-market. It is designed for applications that need low latency, medium throughput data communication in a variety of radio propagation conditions. Due to the unique combination of performance, security and flexibility, this module is ideally suited for M2M applications, such as metering, telematics, asset tracking, remote monitoring ,E-health , mobile pos terminals and sharing bike. General features * Tri-Band FDD-LTE B3/B8/B20 * GPRS/EDGE 900/1800Mhz * Output power - GSM900: 2W - DCS1800: 1W * Control Via AT Commands * Supply voltage range: 3.0V~ 4.3V, Typ: 3.8V * Operation temperature: -40â?? to +85â?? * Dimensions: 24 X 24 X 2.6mm * Weight: 3.0g * GNSS (GPS,GLONASS and BeiDou/Compass, Galileo, QZSS) Specifications for Data transfer * LTE CAT-M1(eMTC) - Uplink up to 375kbps, Downlink up to 300kbps * NB-IoT - Uplink up to 66kbps, Downlink up to 34kbps * EDGE Class - Uplink up to 236.8Kbps, Downlink up to 236.8Kbps * GPRS - Uplink up to 85.6Kbps, Downlink up to 85.6Kbps Other features * USB Driver for Microsoft Windows XP/Vista/7/8 * USB Driver for Windows CE/Mobile * USB Driver for Linux/Android * Firmware update via USB * TCP/IP * PPP * SMS * EMAIL * FTP/HTTP/SSL * VoLTE* * FOTA* Interfaces * USB2.0 x1 (high-speed) * UART x2 (7-wire UART and 2-wire UART interface multiplex from GPIO) * SIM card x1 (1.8V and 3V) * I2C x1 * GPIO x5 * ADC x1 Consumption * Power off: 7uA * PSM: 9uA * Sleep: 1mA * Idle: 11mA
4G with SIM card holder is a wireless module which is designed for the global market. It is a consumptive product; It can be designed in many kinds of applications which can work on LTE-FDD/UMTS/GSM/GPS/GLONASS(Optional) network. On LTE-FDD network, 4G with SIM card holder enables connect to the Internet at DL data speed up to 150Mbps and UL data speed up to 50Mbps. In the area where LTE service are not available, 4G with SIM card holder still enables reliable and secure data connect over 3G(UMTS) or 2G(GSM) network. 4G with SIM card holder provides SMS, MMS, Phonebook functions as well as high speed access, and also audio function. It can be designed in many kinds of applications. Such as Data card, Video monitor, Tablet, Electric-book, MID, Vehicle equipment, etc. General features: EDGE multi-slot class 33 GPRS multi-slot class 33 Compliant to GSM phase 2/2+ Output power: - Class 3 (0.25W) for LTE/UMTS - Class 4 (2 W) for GSM 900 - Class 1 (1 W) for GSM 1800 Control via AT commands (3GPP TS27.005/3GPP TS27.007 ) Supply voltage range 3.3V- 4.2V Low Power consumption - Sleep mode: 3mA - Power down: 16 �¼A Dimensions: 51.0�?30.0�?4.6mm Operation Temperature: -40�°C to +85�°C MSL : 3 Band Configuration LTE-FDD Band 1/3/5/7/8/20/28 LTE-TDD Band 38/40 UMTS Band 1/5/8 GSM Band 3/8 Specifications for GNSS GPS frequency: 1575.42MHz At least support 44 channels Sensitivity - Acquisition: -158dBm - Tracking: -162dBm TTFF - Cold Start: 28s - Warm Start: 18s - Hot Start: 1s Specifications for data Support Release 11 Category 4 LTE-FDD up to 150 Mbps DL,50 Mbps UL LTE-TDD up to 130 Mbps DL,35 Mbps UL DC-HSPA+ up to 42.2Mbps DL,5.76Mbps UL EDGE class 33: 296Kbps DL,236.8Kbps UL GPRS class 33: 107kbps DL,85.6kbps UL CSD up to 14.4 kbps Non transparent mode PBCCH support PPP-stack Coding schemes CS 1,2,3,4 FOTA TCP/IP NDIS Specifications for SMS Point-to-point Mo and MT SMS cell broadcast Text and PDU mode Protocols TCP/ UDP/ PPP/ FTP/ HTTP/ HTTPS/ SMTP*/ SMTPS*/ MMS/ FTPS*/ NTP/ PING/ QMI/ SSL/ NITZ/ CMUX/ MQTT* Additional features VoLTE Phone book PCM DTMF Interfaces: RF connector PCI Express�® Mini Card Interface - Power supply - USB 2.0 high speed - UICC/SIM/UIM card interface 3V, 1.8V - UART - Analog Audio - PCM Antenna connector SIM Card Holder Approvals: RoHS / CE / GCF / RCM / NCC
SIM7600X-H-PCIE is a complete multi-band LTE-FDD/LTE TDD/HSPA+/UMTS/EDGE/GPRS/GSM module solution in Mini PCIE type which supports LTE CAT4 up to 150Mbps for downlink and 50Mbps for uplink data transfer.It is combined with a SIM7600X-H (LCC) module and a Mini PCIE adapter board. Target market: EMEA/Korea/Thailand SIM7600E-H-PCIE * Support 4G LTE FDD Band B1/B3/B5/B7/B8/B20 and TDD Band B38/B40/B41 * Support 3G UMTS/HSPA+ B1/B5/B8 * Support 2G GSM/GPRS/EDGE B3/B8 * GSM/GPRS/EDGEB3/B8 General features * Mini PCIE package * Control Via AT Commands * Supply voltage range: 3.0V~ 3.6V, 3.3V Typical * Operation temperature: -40â??to +85â?? * Bandwidth: 1.4/3/5/10/15/20MHz * 3GPP E-UTRA Release 11 * Dimensions: 50.8*31*5.35mm * Weight: 12.6g Specifications for Data transfer * LTE Downlink up to 150Mbps, Uplink up to 50Mbps * HSPA+ Downlink up to 42Mbps, Uplink up to 5.76Mbps * WCDMA Downlink/Uplink up to 384Kbps * EDGE Downlink/Uplink up to 236.8Kbps * GPRS Downlink/Uplink up to 85.6Kbps Other features * USB Driver for Microsoft Windows 2000/XP/Vista/Win7/Win8/Win10 * USB Driver for Linux /Android * RIL supporting for Android 2.4/4.0/5.0/6.0/7.0 * MBIM to Win8 * Firmware update via USB * TCP/IP/IPV4/IPV6/Multi-PDP/FTP/FTPS/HTTP/HTTPS/SMTP/SMTPS/DNS * SSL3.0/TLS1.0/TLS1.2 * DTMF (Sending and Receiving) * Audio Playing * USB Audio and VoLTE * FOTA * eCall* Interfaces * USB2.0 with High speed up to 480Mbps * UART * GPIO * Antenna: Solder pads for Primary, Rx-diversity and GNSS antennas * (U)SIM card (1.8V/3.0V) * Digital Audio through PCM * Analog Audio (Optional) * Embedded SIM card socket (Optional) * GNSS: GPS/GLONASS/Beidou/Galileo*
30W-ICS Repeater: Interference Cancellation System (ICS) Repeater is a personal network enhancement device with inbuilt Interference Cancellation System ICS Repeater system is designed to solve problems of weak mobile signal, which is much cheaper than adding a new Base Station (BTS). Main operation of RF Repeaters system is to receive low power signal from BTS via radio frequency transmission and then transmit the amplified signal to the areas where network coverage is inadequate. And the mobile signal is also amplified and transmitted to the BTS via the opposite direction.
A DAS is a system of managed hubs and remote antennas that distributes a wireless signal to a series of connected indoor or outdoor multi-band, multi-technology radio heads. ... A main hub takes that signal, digitizes it, and distributes it to other hubs and radio heads via a high-bandwidth fiber optic network
Repeaters system is designed to solve problems of weak mobile signal, which is much cheaper than adding a new Base Station (BTS). Main operation of RF Repeaters system is to receive low power signal from BTS via radio frequency transmission and then transmit the amplified signal to the areas where network coverage is inadequate. And the mobile signal is also amplified and transmitted to the BTS via the opposite direction. Outdoor: Airports, Tourism Regions, Golf Courses, Tunnels, Factories, Mining Districts, Villages etc. Indoor: Hotels, Exhibition Centers, Basements, Shopping Malls, Offices, Packing Lots etc.
The RF front-end stage of the communication system is composed of passive devices such as a filter, a duplexer, a power combiner, an RF connector, and an RF switch. These passive devices are designed to maintain the possible linear characteristics in the operating range, but they have practically nonlinear characteristics. Passive intermodulation occurs when two or more different frequencies are used as inputs to a passive device having nonlinear characteristics. This phenomenon is called Passive IM (PIM). Intermodulation (PIM) signals are added as unwanted noise to an uplink band in a mobile communication system, which is a major noise source that deteriorates the signal to noise ratio (SNR). Therefore, the intermodulation (PIM) signal, which may cause a lot of losses in terms of operation, maintenance, and frequency use efficiency of the mobile communication system equipment, should be removed. A system for removing an intermodulation (PIM) signal existing in an uplink band of a mobile communication system is called a PICS (Passive Intermodulation Canceller System).
The Single Band LTE Repeater is a cell phone signal booster system made up of antennas, cable and a signal amplifier that takes an existing cell signal, typically found outside your home or office, amplifies the signal and then broadcasts it to an inside area that has a weak or no signal.In order for the system to work, there must be an existing, stable outside signal for the system to receive and amplify It can be applied at meeting rooms, conference rooms, museums, galleries, theaters, concert halls, churches, temples, restaurants, classrooms, training centers, factories, banks, trains, bus and more Places that require silence, confidentiality and information security
A mobile phone signal repeater provides the ultimate solution in any area where cellular communications can not work well due to leak of signals. The repeater device features easy installation & operation, build-in indoor antenna and no interference. It could also improve indoor electromagnetism environments, protract cellular battery life and reduce radiation of cellphones. A mobile phone repeater is ideal for house, home, office use.
Dual Band LTE Repeater also known as cell phone repeaters were developed to address the two factors that cause poor cell phone reception. They're designed to amplify a weak outside signal and bypass any obstructions to provide a strong inside signal to an area that was originally lacking.The system works by mounting an outside antenna in a location that currently has signal, which is typically on the roof. The signal is passed from the outside antenna, by a cable to a signal amplifier inside the building. Once the signal is amplified, it is then sent to an inside antenna, where it is broadcast out to the area which needs better reception. The system also works in reverse, with the signal from your phone being amplified and broadcast back to the tower, ensuring strong, two-way communication.
Dual-Band LTE Repeater is used to improve network coverage of mobile phone in home and offices.Dual-Band LTE Repeater is a complete network coverage solution for areas which face problems like disturbance in call, call drops and less network signals. Dual-Band LTE Repeater is placed at a network rich area from where it catches signals from the nearest tower and these signals are transmitted to the area facing the signal problem.It can be applied at meeting rooms, conference rooms, museums, galleries, theaters, concert halls, churches, temples, restaurants, classrooms, training centers, factories, banks, trains, bus and more Places that require silence, confidentiality and information security
