Cube2--C17200 (CDA 172) Beryllium Copper is the most commonly utilized Copper Beryllium alloy and is notable for its highest strength and hardness compared to commercial copper alloys. C17200 alloy contains appr. 2% of beryllium and achieves its ultimate tensile strength can exceed 200 ksi, while the hardness approaches Rockwell C45. Meanwhile, the electrical conductivity is a minimum of 22% IACS in the fully aged condition.C17200 also exhibits exceptional resistance to stress relaxation at elevated temperatures. International Specification: Rods/Bars/Tubes: ASTM B196,251,463; SAE J461,463; AMS 4533,4534,4535; AMS4650,4651; RWMA Class 4 Strips:ASTM B194, AMS4530,4532; SAE J461,463 Sheets: ASTM B194 Wires:ASTM B197, AMS4725, SAE J461,463 Plates:ASTM B194, SAE J461,463; AMS4530,4533,4534,AMS4650,4651; RWMA Class 4. European Standards: CuBe2, DIN 2.1247, CW101C to EN Note: ASTM: American Society for Testing and Materials SAE: Society of Automotive Engineers AMS: Aerospace Materials Specification (Published by SAE) RWMA: Resistance Welder Manufacturers' Association Note: Unless otherwise specified, material will be produced to ASTM. Available Sizes: Custom Diameter & Sizes, Random Mill lengths Available Products (forms): Round bars, Round strips, Round wires, Round tube, Flat bars, Square bars, Rectangular bars, Hexagon bars, Plates, Sheets, Coils Custom shapes are available upon request. Chemical Composition: Be: 1.85-2.10% Co+Ni: 0.20% Min. Co+Ni+Fe: 0.60% Max. Cu: Balance Note: Copper plus additions equal 99.5% minimum Typical Physical Properties: Density (g/cm3): 8.36 Density before age hardening (g/cm3): 8.25 Elastic Modulus (kg/mm2 (103)): 13.40 Thermal Expansion Coefficient (20 ípC to 200 ípC m/m/ípC): 17 x 10-6 Thermal Conductivity (cal/(cm-s-ípC)): 0.25 Melting Range (ípC): 870-980 Note: 1). the units are based upon Metric. 2). the typical physical properties apply to age hardened products.
CuCo1Ni1Be--CW103C (DIN 2.1285) Cobalt Nickel Beryllium Copper Alloy contains approximately 1% Cobalt, 1% Nickel and 0.5% Beryllium. After hot forging and heat treatment processes this material gains considerably hardness, electrical and thermal conductivity as well. It is possible to have different combinations of electrical conductivity and hardness by changing the heat treatment conditions;CuCo1Ni1Be also Offers good strength and hardness characteristics coupled with conductivity in the range of 45-60 percent of copper with ultimate tensile and hardness properties approaching 140 ksi and RB 100 respectively, all of its properties are quite the same as CuCo2Be-C17500 and CuNi2Be-C17510. International Specification: Rods/Bars/Tubes: ASTM B441, SAE J461,463; RWMA Class 3 Sheets: ASTM B534 Wires: ASTM B441 Plates: ASTM B534, SAE J461,463; RWMA Class 3 European Standards: CuCo1Ni1Be, DIN 2.1285; CW103C to EN Note: ASTM: American Society for Testing and Materials SAE: Society of Automotive Engineers AMS: Aerospace Materials Specification (Published by SAE) RWMA: Resistance Welder Manufacturers' Association Note: Unless otherwise specified, material will be produced to ASTM.
CuCrNi2Si ¿C UNS.C18000 Copper Chromium Nickel Silicon Alloys, which also called Beryllium Free Copper alloy, meets the mechanical requirements of RWMA Class 3 Copper, is a very hard heat treatable copper based alloy with an economical higher strength and high conductivity, and C18000 Alloys is utilized when a combination of very good mechanical strength along with moderate electrical and thermal electrical conductivity are required. Furthermore, C18000 alloy is an excellent substitute for copper beryllium alloys C17500 and C17510 in terms of many applications. International Specification: Rods/Bars/Plates/Sheets: UNS.C18000, CDA180, RWMA Class 3 European Standards: CuCrNi2Si, DIN 2.0855, CW111C to EN Note: ASTM: American Society for Testing and Materials RWMA: Resistance Welder Manufacturers' Association Note: Unless otherwise specified, material will be produced to DIN & RWMA.
Cube2--c17200 (cda 172) beryllium copper is the most commonly utilized copper beryllium alloy and is notable for its highest strength and hardness compared to commercial copper alloys. C17200 alloy contains appr. 2% of beryllium and achieves its ultimate tensile strength can exceed 200 ksi, while the hardness approaches rockwell c45. Meanwhile, the electrical conductivity is a minimum of 22% iacs in the fully aged condition.C17200 also exhibits exceptional resistance to stress relaxation at elevated temperatures. Available sizes: Custom diameter & sizes, random mill lengths International specification: ú¿¦·+O¦µ+¦ú¬ Rods/bars/tubes: astm b196, 251, 463; sae j461, 463; ams 4533, 4534, 4535; ams4650, 4651; Rwma class 4 Strips:astm b194, ams4530, 4532; sae j461, 463 Sheets: astm b194 Wires:astm b197, ams4725, sae j461, 463 Plates:astm b194, sae j461, 463; ams4530, 4533, 4534, ams4650, 4651; rwma class 4. European standards: cube2, din 2.1247, cw101c to en Note: Astm: american society for testing and materials Sae: society of automotive engineers Ams: aerospace materials specification (published by sae) Rwma: resistance welder manufacturers' association Note: unless otherwise specified, material will be produced to astm. Plywood cases/plastic pipes/wooden cases
Light metal scrap of alumium cans. 20 Feet Container (20 Ton)
Ca-Al alloy Specification: Ca: 60-95%, Al: Balance Size: 30-100mm (Irregular lumps), 3-30mm(coarse granules),
Calcium metal series including: Calcium ingot, Calcium lump, Calcium turning, Calcium granular Chemical composition: Ca: 99.0%min and Ca: 98.5%min Calcium lumps: 30-100mm, 30-150mm,30-200mm. Calcium granulars: 0-2mm, 0-3mmú¼0-6mm Calcium turning: 30-80mm (Length), 6-8mm (Width), 0.7-3.6mm (Thickness) Or as per customers special and detailed specifications Application: in Metallurgy for steel-making, special alloy smelting, battery line, medicine adding, etc.
Ca-Mg alloy Specification: Ca: 30%, Mg:70% Size: 30-100mm (Irregular lumps) or as per clients requirements. Application: Additive of middle alloys for metal instrument founding mills.
Cored wire: CaSi cored wire, FeCa cored wire Pure Ca cored wire, BaSiCa cored wire, BaSiCaAl cored wire, Carbon cored wire, etc. Diameter of cored wire: 9mm,13mm,14mm,15mm,16mm Feeding type: inside pay-off, outside pay-off Shape: Round Package: Horizontial/Vertical caged, Palletized, Polyethylene sheet wrapped in each coil.
Magnesium metal series including: Magnesium ingot, Magnesium granular, Magnesium powder, passivation Magnesium granular. Chemical composition: Mg;99.90%min, Mg;99.95%min ,Mg;99.99%min Magnesium Ingots : 15kg/pc 7.5kg/pc 1kg/pc Magnesium granular, Magnesium powder: 2mm-0.015mm Packing: 1000 kg per woven bag or up to customer's requirement. Application: metallurgical casting, Military industry and metal instrument manufacture, in desulfuration and producing of magnesium alloy, also can be used in chemical industry. Produce as customers requests.
Xundake procures a variety of quality machinery parts through an extended network of suppliers. Contact us to know more about the business opportunities in China.
Xundake procures a variety of quality machinery parts through an extended network of suppliers. Contact us to know more about the business opportunities in China.
Made of steeless 316, high polished.
Made of steeless 316, high polished. All kind of size.
Magnesium ingot: We can supply various kinds of magnesium related products .Such as magnesium ingot, magnesium alloy, magnesium granular(powder), etc. Magnesium ingot as below:(note:customers special request available!) Magnesium ingot Mg:99.9%min. Al: 0.02%max. Si 0.02%max. Mn 0.02%max. Magnesium ingot size: 7.5kg+/- 0.5kg High purity magnesium: Mg:99.95%min. Al: 0.0040%max. Fe 0.0045%max. Si 0.0070%max. Ni 0.0010%max. Mn 0.0070%max. Cu 0.0030%max. Magnesium ingot size: 7.5kg+/- 0.5kg Mg:99.99%min. Al: 0.0020%max. Fe 0.0045%max. Si 0.0020%max. Ni 0.0010%max. Mn 0.0020%max. Cu 0.0020%max. Magnesium ingot size: 7.5kg+/- 0.5kg Magnesium alloys such as : Az91d, az91hp , az63 , za10, am60, am50, am20, ze41a and so on with the standard of gb/t5153-2003, gb/t19073-2003 and astmb94-92. Magnesium ingot size: 7.5kg+/- 0.5kg Packed on pallets with plastic covering and steel tape to tighten
HMS 1 & 2. Container 20"
We can supplier high quality mill scale from Australia and India to china Via containers and bulk shipments. Now, we have 5500mt spot at west Indian. 3500mt at Australia for ready shipment. We also provide steel scraps from Australia to China. Container or bulk vessel
Usage: used in electro, metallurgy and chemical industry. 1. Widely applied to refractory material and power metallurgy industry to improve the heat resistance, wear resistance and oxidation resistance. Products made of it are applied in steel smelting furnace, kiln hood and kiln furniture etc. 2. In the chemical line of organic silicon, industrial silicon powder is basic raw material that high polymer of organic silicon formatting. Such as using for producing organic monomer, silicon oil, silicon rubber antiseptic to improve the characteristics of insulating, corrosion-resistance and waterproof performance etc. 3. Industrial silicon powder is sublimated into monocrystaline silicon, which is widely used in hi-tech field as an essential raw material for integrated circuit and electronic element. 4. In metallurgy and foundry line, industrial silicon powder is regarded as to be iron base alloy additive, the alloy pharmaceutical of silicon steel, thus improve the steel hardenability (1)no mark or mark as client's requirement (2)1mt/bag or as client's requirement (3)plastics woven bag
Metal scrap
Characteristics: High saturation flux density High permeability Low coercive force Low core losses(1/3-1/5 of silicon steel) Low excitation current Good thermal stability and aging stability.
