1. Use (H) RW 12-27 drop fuse and pull-load drop fuse are outdoor high-voltage protective appliances, which are assembled on the high-voltage side of distribution transformer or branch lines of distribution line, and are used for overload and short-circuit protection of transmission lines and power transformers and for sharing rated load current. 2. Brief introduction of structure The drop fuse consists of two parts: insulating bracket and fuse pipe. The static contacts are installed at both ends of the insulating bracket, and the movable contacts are installed at both ends of the fuse pipe. The fuse pipe consists of an inner arc extinguishing tube and an outer epoxy glass tube. Pull-load drop fuse adds elastic auxiliary head and arc extinguishing cover to divide and close load current. When a drop fuse is in normal operation, the fuse pipe is tensioned by means of the fuse. Then a closed position is formed. When the system fails, the fault current causes the fuse to fuse rapidly and form an arc. The arc extinguishing tube is heated by the arc and decomposes a large number of gases, which forms a high pressure in the tube and blows longitudinally along the pipeline. The arc is rapidly elongated and extinguished. After the fuse is fused, the lower moving contact loses tension and turns down. The locking mechanism releases the fuse tube, and the fuse tube falls down, forming an obvious breaking position. When the load needs to be pulled, the contact is pulled by the insulating rod. At this time, the active and static contacts are still in contact. The contacts are pulled by the insulating rod, and the auxiliary contacts are separated. Arc is generated between the auxiliary contacts. The arc is elongated in the slot of the arc extinguishing hood. At the same time, the arc is extinguished when the current passes zero. 3. Implementation criteria The product performance conforms to GB15166.3-94 national standard and IEC282-2 international standard. 4. Conditions of Use 1. Environmental temperature: - 40 ~40 C; 2. No more than 1200 m above sea level; 3. The wind speed is not more than 35m/s. 4. Earthquake intensity does not exceed 8 degrees. 5. Fuses are not suitable for the following places: A. Places where there is a danger of combustion or explosion; B. Places with violent vibration or shock; C. Areas with heteroelectrochemical gases, severe air pollution and salt fog. 5. Instructions for Order 1. Product type, name, rated voltage, rated current and rated switching-on current; 2. Environmental requirements (anti-pollution, plateau type); 3. Special requirements can be consulted with our company. Manufacturer of intelligent switch cabinet--low-voltage, high voltage power distribution switch cabinet, also have many other electric equipment electric power accessories, intelligent transmission and distribution automation system
kit kat fuse , porcelain fuse , ceramic fuse , rewire fuse , Current : 240 V-500 V, 30 A - 500 A , in all type Creamy white color
Features/Benefits 600 V 110 -30 A Class CC and Midget fuse cover puller that offers increased protection when removing fuses. Simple removal without the need for a separate puller. Meets Dead Front requirements. Easily gangable with 1 8" diameter wire. For use with all 600 V Class CC and Midget 1 10 -30 A fuses. Label provided for easy fuse identification. Recommended Fuse Blocks L60030C and L60030M Ordering Information Poles Pack Quantity Catalog Number Ordering Number 1 10 SPL001 0SPL0001T 1 100 SPL001 0SPL0001H 2 5 DSPL001 DSPL0001Z 2 100 DSPL001 DSPL0001H 1 10 SPL001PCB SPL0001PCBT
Description The Littelfuse Class CC, CD and midget blocks offer generous space savings and enhanced value. DIN-rail mounting and universal mounting holes are available as well as an indication feature on all Class CD fuse blocks. Features/Benefits Space-saving design Universal mounting holes for easy replacement. Indication offered on CD blocks. One hand release from DIN rail optional. Rejection feature that prevents the insertion of fuses with lower interrupting rating or voltage ratings. Clip design reduces resistance and heat . Non DIN-rail fuse blocks have interlocking feature allowing ganging for any number of poles. Covers available for all amperages to enhance safety. Specifications Voltage Rating 600 Vac/dc Ampere Ratings L600M Midget (10x38): 30 A L600C Class CC: 30 A LFC Class CD: 60 A L600CM Class CC & Midget: 30 A Dielectric strength 1200 V minimum Materials Clip/terminals: Tin-plated copper alloy Box lug: Copper Screw & captive pressure plate: Zinc-plated steel Base: Thermoplastic UL94 V-0 flammability rating Withstand Rating L60030C: 200kA (SCCR) L60030M:10kA, 20kA or 100kA based on the Midget fuse used LFC600: 200kA Approvals L600M: UL Recognized (File: E14721) CSA Certified (File: LR7316) L600C: UL Listed (File: E14721) CSA Certified (File: LR7316) LFC: UL Listed (File: E14721) CSA Certified (File: LR7316) L600CM: UL Recognized (File: E14721) CSA Certified (File: LR7316) Environmental RoHS Compliant, Lead (Pb) Free Recommended Fuses Class CC Blocks: CCMR, KLDR, KLKR Class CM Block: Fuses same as CC & Midget Blocks Class CD Blocks: CCMR Midget Blocks: BLF, BLN, BLS, FLA, FLM, FLQ, FLU, KLK, KLKD, KLQ L60030C1C L60030C2C L60030C3C L60030C1PQ L60030C2PQ L60030C3PQ L60030C1SQ L60030C2SQ L60030C3SQ L60030C1CDINR L60030C2CDINR L60030C3CDINR L60030C1PQDINR L60030C2PQDINR L60030C3PQDINR L60030C1SQDINR L60030C2SQDINR L60030C3SQDINR L60030M1C L60030M2C L60030M3C L60030M1PQ L60030M2PQ L60030M3PQ L60030M1SQ L60030M2SQ L60030M3SQ L60030M1CDINR L60030M2CDINR L60030M3CDINR L60030M1PQDINR L60030M2PQDINR L60030M3PQDINR L60030M1SQDINR L60030M2SQDINR L60030M3SQDINR
17AME+FUSE Combination YANGZHOU WUYUE ELECTRIC CO.,LTD 17AME+fuse is a combination of thermal protector and thermal cut off. It has double protections. Safer and more reliable. Special Features Small size, long life and high reliability; Connected a cut off in series to save process in final applications. 100% Snap Action Both temperature and current sensitive; Sealed housing, water proof; The type of cut off is optional and customized; The types and length of wire are optional. Electric Specification 20A / 16V DC 10A / 250V AC 20A / 125V AC Technical Parameters Operating temperature range:45 degree centigrade~180 degree centigrade Temperature fuse:Customizing Temperature Tolerance:±3 degree centigradeï¼? ±5 degree centigrade Application Electric heating cushion Pet mat Electric blanket Small appliances
KTK fast-acting 13/32" x 1-1/2"supplemental fuse Fast-acting supplemental fuse. Black color code (600 Vac max). For superior protection, Eaton recommends upgrading to Bussmann series Low-Peak Class CC fuses. Agency information â?¢ UL Listed, Std. 248-14, Guide JDYX, File E19180, CSA Certified, C22.2 No. 248.14, Class 1422-01, File 53787, HRC-MISC, RoHS compliant, CE Features â?¢ Black color code for 600 Vac rating â?¢ Fast-acting for resistive loads â?¢ Melamine tube construction with nickel-plated bronze endcaps Typical applications â?¢ Control circuits â?¢ Lighting circuit protection â?¢ Meter circuits KTK-1/10 KTK-1/8 KTK-2/10 KTK-1/4 KTK-3/10 KTK-4/10 KTK-1/2 KTK-6/10 KTK-3/4 KTK-1 KTK-1-1/4 KTK-1-1/2 KTK-2 KTK-2-1/2 KTK-3 KTK-3-1/2 KTK-4 KTK-5 KTK-6 KTK-7 KTK-7-1/2 KTK-8 KTK-9 KTK-10 KTK-12 KTK-15 KTK-20 KTK-25 KTK-30
Catalog symbols: EV20-(amp) 20 mm diameter EV25-(amp) 25 mm diameter EV30-(amp) 30 mm diameter Description: Eatons Bussmann® series Electric Vehicle (EV) fuses for the protection of high power battery charging and management systems up to 500 Vdc in ratings from 50 to 400 amps. Specifications: Ratings Volts - 500 Vdc Amps 50-400 A Interrupting rating Max DC 20 kA Min DC 200% Agency information Designed to: JASO D622 ISO 8820-8 Manufactured under a TS16949 quality system for compliance with automotive requirements RoHS compliant REACH declaration available upon request Packaging 20 mm fuses: 250 fuses per box 25 mm fuses: 100 fuses per box 30 mm fuses: 100 fuses per box Features: Higher voltage rating provides overall system efficiency using smaller, more economical conductors while meeting the needs of higher voltage battery packs. Higher interrupting rating protects high capacity battery packs needed for vehicle acceleration and range requirements. Up to ten times faster opening under high fault current conditions helps assure reliable protection of circuits and components. Requires up to 48% less space than conventional high speed fuses to help reduce space and weight. Data logging system marks each fuse with a serial number and date code for traceability of Critical to Quality characteristics. To help project the life of the fuse in your application, unique driving profiles and conditions can be simulated to verify proper fuse size and performance under a wide range of driving behaviors. Operation as low as 200% overload provides back up protection to the battery management system. Can be applied in parallel to realize greater ampacity within sizing guidelines.
CH modular, IP20 finger-safe DIN-Rail holders for Class CC, midget and PV fuses Bussmann series CH DIN-Rail fuse holders are for UL Class CC and midget fuses, and IEC 10x38mm fuses. They are available with and without indication in 1-, 2- and 3-pole IP20 finger-safe versions. A variety of accessories extends their application flexibility and they may be ganged together to meet specific application requirements. Ratings Volts 600 V (or less) UL 690 V (or less) IEC 1000 Vdc (or less) photovoltaic (PV) Amps 30 A UL 32 A IEC SCCR 33 kA photovoltaic 200 kA RMS Sym. (CHCC, CHM*) * CHM SCCR is fuse interrupting rating dependent. Agency information CHCC, CHM; UL Listed Guide IZLT, Recognized Guide IZLT2, File E14853 CHPV, UL Listed to 4248-19, Guide IZMR, File E348242 CSA File 47235, CHPV and CHM - Class 6225-30, CHCC - Class 6225-01 IEC 60269-2 (CHM, CHPV) CCC RoHS compliant CE Storage and operating temperature -4°F (-20°C) to +194°F (90°C) indicating -4°F (-20°C) to +248°F (120°C) non-indicating Features High SCCR rated, UL Listed Class CC holder with optional open fuse indication for 600 V and 48 Vdc (see catalog number table for details) Enhanced safety with IP20 finger-safe construction UL Recognized midget and IEC 10x38mm holders with factory assembled neutral pole option Agency ratings up to 1000 Vdc for use with PV fuses. Available remote PLC fuse indication module Wiring flexibility with terminals rated for use with 75°C or 90°C solid, stranded and fine stranded wire, and fork terminals and comb busbars. (Use any higher temperature insulations at the 90°C ampacity with appropriate derating.) Complete range of UL Listed and high SCCR rated one- and threephase finger-safe comb busbars and power feed lugs Optional hex head terminal screw makes it easier to achieve necessary torque values CHM1DIU CHM1DU CHM2DIU CHM2DU CHM3DIU CHM3DU CHM4DIU CHM4DU CHM1DNIU CHM1DNU CHM1DNXU CHM1DCIU CHM1DCU CHM2DCIU CHM2DCU CHM3DCIU CHM3DCU CHM4DCIU CHM4DCU CHCC1DIU CHCC1DU CHCC2DIU CHCC2DU CHCC3DIU CHCC3DU CHCC1DI-48U CHPV1IU CHPV1U CHPV2IU CHPV2U
Indicators High speed square body fuses are available with the following indicators. Visual indicator The indicator situated in one end plate is clearly visible as soon as the fuse has operated. The minimum rated voltage for operating the indicator is 20 V. Type T indicator The indicator is situated on one cover plate with a cover plate tag to accommodate an auxiliary switch. The minimum rated voltage for operating the indicator is 20 V. A special low rated voltage indicator (1.5 V) is available on request. Type K indicator The indicator is situated on the fuse body. It is covered by an adapter for snap-on mounting of a microswitch. The rated operating voltage of the indicator is 1.5 V. As a matter of safety, the factory mounted adapter must not be removed from the fuse. Microswitches High speed square body fuses with either Type T or K indicators can be equipped with a microswitch for remote signaling of fuse operation. All microswitches have one normally open (NO) and one normally closed (NC) contact. Ratings Volts 250 Vac Amps 5 A 170H0235 170H0236 170H0237 170H0238 170H0069
CH modular, IP20 finger-safe DIN-Rail holders for Class CC, midget and PV fuses Bussmann series CH DIN-Rail fuse holders are for UL Class CC and midget fuses, and IEC 10x38mm fuses. They are available with and without indication in 1-, 2- and 3-pole IP20 finger-safe versions. A variety of accessories extends their application flexibility and they may be ganged together to meet specific application requirements. Ratings Volts 600 V (or less) UL 690 V (or less) IEC 1000 Vdc (or less) photovoltaic (PV) Amps 30 A UL 32 A IEC SCCR 33 kA photovoltaic 200 kA RMS Sym. (CHCC, CHM*) * CHM SCCR is fuse interrupting rating dependent. Agency information CHCC, CHM; UL Listed Guide IZLT, Recognized Guide IZLT2, File E14853 CHPV, UL Listed to 4248-19, Guide IZMR, File E348242 CSA File 47235, CHPV and CHM - Class 6225-30, CHCC - Class 6225-01 IEC 60269-2 (CHM, CHPV) CCC RoHS compliant CE Wire range 75°C and 90°C Cu 18-4 AWG (0.8-21.1mm2) Solid, stranded and fine stranded* * See data sheet 10430 for application details. Terminals Single or dual conductors Comb busbar Terminal screws Standard phil-slot Optional hex head (order by adding -H suffix to the catalog number, e.g., CHM1DU-H) Torque 30 lb-in (3.4 Nâ?¢m) maximum Flammability UL 94V0, self-extinguishing Storage and operating temperature -4°F (-20°C) to +194°F (90°C) indicating -4°F (-20°C) to +248°F (120°C) non-indicating Features High SCCR rated, UL Listed Class CC holder with optional open fuse indication for 600 V and 48 Vdc (see catalog number table for details) Enhanced safety with IP20 finger-safe construction UL Recognized midget and IEC 10x38mm holders with factory assembled neutral pole option Agency ratings up to 1000 Vdc for use with PV fuses. Available remote PLC fuse indication module Wiring flexibility with terminals rated for use with 75°C or 90°C solid, stranded and fine stranded wire, and fork terminals and comb busbars. (Use any higher temperature insulations at the 90°C ampacity with appropriate derating.) Complete range of UL Listed and high SCCR rated one- and threephase finger-safe comb busbars and power feed lugs Optional hex head terminal screw makes it easier to achieve necessary torque values CHCC1DIU CHCC1DU CHCC2DIU CHCC2DU CHCC3DIU CHCC3DU CHCC1DI-48U
Ratings Volts 690 Vac/500 Vdc (IEC) 700 Vac/500 Vdc (UL) Amps 6-200 A IR CT: IEC 90 kA RMS Sym., 40 kA at 500 Vdc, UL 200 kA RMS Sym., 50 kA at 500 Vdc ET, EET, FE and FEE: 200 kA RMS Sym.,50 kA at 500 Vdc Operating class aR Agency information Designed and tested to BS88 part 4 and IEC 60269 Part 4 UL Recognized* CCC for ET, FE, EET, FEE CE 35FE 40FE 35FE 45FE 50FE 63FE 71FE 80FE 90FE 100FE
D16, D27, D33, D125 DIN Type D Diazed fuses DIN style Type D ceramic body low voltage fuses. Ratings Volts 500 Vac Amps 2-100 A IR 50 kA Agency information IEC 60269 and DIN 49515, CE 2D16 4D16 6D16 10D16 16D16 20D16 25D16 2D27 4D27 6D27 10D27 16D27 20D27 25D27 35D33 50D33 63D33 80D125 100D125
500 Vac/dc (UL), 35 to 1600 A North American style bolted tags high speed fuses, for the protection of DC common bus, power converters/rectifiers and reduced rated voltage starters. Ratings Volts 500 Vac (UL) 500 Vdc (35-800 A only) Amps 35-1600 A IR 200 kA RMS Sym. 50 kA at 500 Vdc Agency information UL Recognized, JFHR2, E91958, FWH-_B (35-200 A) and FWH-_A (1000 and 1200 A), JFHR2, E56412 FWH-_A (225-800 A) CSA Class 1422-30, File 53787 (35-1600 A) CE FWH-35B FWH-40B FWH-45B FWH-50B FWH-60B FWH-70B FWH-80B FWH-90B FWH-100B FWH-125B FWH-150B FWH-175B FWH-200B FWH-225A FWH-250A FWH-275A FWH-300A FWH-325A FWH-350A FWH-400A FWH-450A FWH-500A FWH-600A FWH-700A FWH-800A FWH-1000A FWH-1200A FWH-1400A FWH-1600A
FNQ-R Class CC Limitronâ?¢ time-delay, rejection-type fuse Time-delay, branch circuit, rejection-type fuse. For superior electrical protection, Eaton recommends upgrading FNQ-R fuse applications to Bussmann series Low-Peak LP-CC fuses, see page 1-5. For dimensions. Ratings Volts 600 Vac (or less) 300 Vdc (15-20 A) 32 Vdc (self certified) Amps 1/4-30 A IR 200 kA RMS Sym. 20 kA DC (15 and 20 A only) Agency information UL Listed, Std 248-4, Class CC, Guide JDDZ, File E4273, CSA Certified, Class 1422-01, File 53787, RoHS compliant, CE Features Class CC rejection feature, with appropriate fuse block, prevents inserting lesser-rated supplementary fuses Time-delay compatible with inrush characteristic of small control transformers Current limitation at Class CC levels provides maximum component short-circuit current rating protection 200 kA interrupting rating provides high ratings for control circuit locations Typical applications Line protection, small control transformers Industrial controls and panels Isolated, in-line fuse holders FNQ-R-1/4 FNQ-R-3/10 FNQ-R-4/10 FNQ-R-1/2 FNQ-R-6/10 FNQ-R-3/4 FNQ-R-8/10 FNQ-R-1 FNQ-R-1-1/8 FNQ-R-1-1/4 FNQ-R-1-3/10 FNQ-R-1-4/10 FNQ-R-1-1/2 FNQ-R-1-6/10 FNQ-R-1-8/10 FNQ-R-2 FNQ-R-2-1/4 FNQ-R-2-1/2 FNQ-R-2-8/10 FNQ-R-3 FNQ-R-3-2/10 FNQ-R-3-1/2 FNQ-R-4 FNQ-R-4-1/2 FNQ-R-5 FNQ-R-5-6/10 FNQ-R-6 FNQ-R-6-1/4 FNQ-R-7 FNQ-R-7-1/2 FNQ-R-8 FNQ-R-9 FNQ-R-10 FNQ-R-12 FNQ-R-15 FNQ-R-17-1/2 FNQ-R-20 FNQ-R-25 FNQ-R-30
HRC Fuse Link & fuse Base Available Brands : Schneider, Siemens, ABB, Legrand, C&S, Eaton, Larsen & Toubro, Havells, Indoasian # HRC Fuse Link & fuse Base # Panel #HRC Fuse # Link # Base # Arc Fuse #Fuses # Saudi Arabia # Oman # Qatar # Yemen # Dubai # Electricals # Electric
Description: 1:Conforms to IEC 60269-2; 2:CE and CCC certification, meeting the requirement of various designs Characteristics: 1:In a compact size and spare little space 2:Standard Voltage 500V/690Vac 3:Three kinds of features :gG/aM/aR 4:Modular bases are easy to install Parameter: Model:R(size) G(current);R(size) M(current);R(size) H(current) Operating class: gG/aM/aR/aR Dimension of fuse:10*18mm;14*51mm;22*58mm Rated voltage:500V(gG/aM);690v(High speed fusing) Current: 1.5-125 A Rated breaking capacity:80ka(gG/aM);200ka(High speed fusing)
Pboy series Rated voltage: 125Vdc Rated current: 5-500A Several control process for guaranteeing the comformity Grade H inported tube resisting high temprature and corrosion,more safety and reliable Integrated contacts,lower contacting resistance,low temprature rise and power loss gG characteristics,full range protaection Unique "quality tracking code"for each product
Fuses : We carry brands such as EM, Bell Fuse, Cooperbussman, Littelfuse, San-O and many others.
Bussmann is the world leading manufaturer for circuit protection. 170 series product is used widely in high power inverter, rectifier, convertors which need to protect the semiconductor. The product part no: 20 170m8 series, e.G:170m8056 170t7020 170e2091 170e2093 170e2095 170e2097 170e2098 170e2161 170e3579 170e3581 170e3586 170e3949 170e4276 170e5417 170e5420 170e5421 170e6143 170f3002 170f3003 170f3004 170f3005 170h3003 170h3004 170h3005 170h3006 170l7278 170l7290 170l7299-h 170l9572 170l9576 170l9578 170l9581 170l9583 170l9665 170l9868 170t8073 1~10pcs/box; Standard lot size: size000~size4 Weight: depends on products Dimensions: depends on products
BMfuse-a 15 years Bussmann distributor. Bussmann is the world leading brand in fuse industry with 100+ years as a professional fuse manufacturer. PN list are: FWH-100C FWH-125C FWH-150C FWH-175C FWH-200C FWH-225C FWH-250C FWH-275C FWH-300C FWH-325C FWH-350C FWH-35C FWH-400C FWH-40C FWH-450C FWH-45C FWH-500C FWH-50C FWH-600C FWH-60C FWH-700C FWH-70C FWH-800C FWH-80C FWH-90C
