1. Chopped basalt fiber Basalt fiber is a kind of inorganic fiber material. Chopped basalt fiber is an inorganic mineral fiber with a length of less than 50mm and can be evenly dispersed in cement concrete. 2. Characteristics of chopped basalt fibers (1) The naturalness of raw materials. Because the raw material for producing continuous basalt fiber depends on the natural volcanic extrusive rock, there are no ingredients harmful to human health except that it is inherently high in chemical stability and thermal stability. (2) Comprehensive performance. Basalt fiber is acid resistant and alkali resistant. It is both low temperature and high temperature resistant. It is insulated and insulated by heat and electricity. Its tensile strength is higher than that of large tow carbon fiber. Its elongation at break is even better than that of small tow carbon fibers. It has high compressive strength, shear strength and adaptability to aging, and has good comprehensive properties in harsh environment. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of steel fiber and polyester fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with asphalt concrete, cement concrete and mortar. The newly mixed basalt fiber concrete has stable volume, good workability and durability, and has superior high temperature resistance, anti-seepage, crack resistance and impact resistance.
1. Basalt short fiber - a new material to replace steel fiber. Basalt short fiber is an inorganic mineral fiber with a length of less than 50mm, which can be evenly dispersed in cement concrete. 2. Characteristics of basalt short fiber (1) the specific gravity of steel fiber is 7.8 and that of cement concrete is 2.5. After mixing, the specific gravity of steel fiber is higher than that of cement, and the cement will sink and have poor dispersion. The specific gravity of basalt short fiber is 2.6, which is basically equivalent to that of cement concrete. After mixing, it does not sink, has good dispersion, is degradable, and is green. The road surface will not be as hard as steel fiber, resulting in car driving noise.. (2) Basalt staple fiber is a real "multifunctional" fiber. Acid and alkali resistance (especially alkali resistance, fully applicable to cement concrete), low and high temperature resistance, insulation and sound insulation. The tensile strength is three times that of steel fiber. The corrosion resistance of basalt fiber is better than that of steel fiber. The compressive strength is 20% higher than that of steel fiber, which is suitable for harsh environment. It has excellent comprehensive performance. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of 50% steel fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with cement concrete and mortar. Fresh basalt fiber concrete has stable volume, good workability and durability, and has excellent high temperature resistance, impermeability, crack resistance and impact resistance.
1. Basalt short fiber - a new material to replace steel fiber. Basalt short fiber is an inorganic mineral fiber with a length of less than 50mm, which can be evenly dispersed in cement concrete. 2. Characteristics of basalt short fiber (1) the specific gravity of steel fiber is 7.8 and that of cement concrete is 2.5. After mixing, the specific gravity of steel fiber is higher than that of cement, and the cement will sink and have poor dispersion. The specific gravity of basalt short fiber is 2.6, which is basically equivalent to that of cement concrete. After mixing, it does not sink, has good dispersion, is degradable, and is green. The road surface will not be as hard as steel fiber, resulting in car driving noise.. (2) Basalt staple fiber is a real "multifunctional" fiber. Acid and alkali resistance (especially alkali resistance, fully applicable to cement concrete), low and high temperature resistance, insulation and sound insulation. The tensile strength is three times that of steel fiber. The corrosion resistance of basalt fiber is better than that of steel fiber. The compressive strength is 20% higher than that of steel fiber, which is suitable for harsh environment. It has excellent comprehensive performance. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of 50% steel fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with cement concrete and mortar. Fresh basalt fiber concrete has stable volume, good workability and durability, and has excellent high temperature resistance, impermeability, crack resistance and impact resistance.
1. Feature Bow shape in cross section, it looks like ripple outside. 2. Specification Lengths of current products are 25mm, 30mm, 35mm, 38mm, 40mm, 50mm. Width is 2.0-2.6mm, thickness is 0.4-0.6mm, wave length is 6-7mm, wave height is 2mm��0.2. We can produce the products according to customer's requirements. 3. Usage The projects blending the ripple steel fibre with concrete in a certain ratio will evidently strengthen bending resistance, stretching resistance, abrasion resistance and pressure resistance. It is widely used in highway, bridge, tunnel, airport runway, basic structure construction of tall building, as well as shock resistance structure and high temperature kiln stove construction. 4. Technical parameter Tensile strength: >750MPa They are packed in bags made of two layers of paper and a piece of plastic film. 25kg/bag, 40 bags per pallet, and 20 metric tons per 20ft container. we also pack the products according to your requirement.
Material£º #45 steel wire Tensile strength :> 700mpa Quality Standards: ASTM- A 820/A 820M ¨C 04 Packing: 25kg/bag 20kg/bag. 25kg/bag 20kg/bag.
Material£º Low-carbon steel wire Tensile strength :> 1000mpa Quality Standards: ASTM- A 820/A 820M ¨C 04 Packing: 25kg/bag 20kg/bag Common Specifications type Length£¨mm£© Diameter(mm) L/D Tensile strength (MPA) QR-D-30/30 30 1.0 30 ¡Ý1000 QR-D-40/30 30 0.75 40 ¡Ý1000 QR-D-60/30 30 0.5 60 ¡Ý1000 QR-D-45/35 35 0.75 35 ¡Ý1000 QR-D-65/35 35 0.55 35 ¡Ý1000 QR-D-50/50 50 1.0 50 ¡Ý1000 QR-D-66/60 60 0.9 66 ¡Ý1000 QR-D-80/60 60 0.75 80 ¡Ý1000. 25kg/bag 20kg/bag.
Material: CARBON STEEL Tensile strength :> 800mpa Length: 1 inch Quality Standards: ASTM- A 820/A 820M ¡§C 04 Packing: 25kg/bag. 25kg/bag.
Material : Low-carbon steel wire Tensile strength :> 1000mpa Quality Standards: ASTM- A 820/A 820M ¨C 04 Packing: 25kg/bag Common Specifications type Length£¨mm£© Diameter(mm) L/D Tensile strength (MPA) QR-D-30/30 30 1.0 30 ¡Ý1000 QR-D-40/30 30 0.75 40 ¡Ý1000 QR-D-60/30 30 0.5 60 ¡Ý1000 QR-D-45/35 35 0.75 35 ¡Ý1000 QR-D-65/35 35 0.55 35 ¡Ý1000 QR-D-50/50 50 1.0 50 ¡Ý1000 QR-D-66/60 60 0.9 66 ¡Ý1000 QR-D-80/60 60 0.75 80 ¡Ý1000. 25kg/bag.
Material: CARBON STEEL Tensile strength :> 380mpa Length: 1 inch Quality Standards: ASTM- A 820/A 820M ¡§C 04 Packing: 25kg/bag. 25kg/bag.
Chopped steel wools are used in brake pad and clutch of automobile, motorcycle, locomotive and airplane as raw material with excellent properties of stability, low wear rate and good heat dissipation. So far, no substitute has been found to match its properties. 1. Specification D0-160, D1-80, AD1-80, 1-80, 3L-80, 3-60, Q4-80 2. Packing They are packed in bags made of two layers of paper and a piece of plastic film. 25kg/bag, 40 bags per pallet, and 20 metric tons per 20ft container. We also pack the products according to your requirement. 3. Chemical Composition (%) C Si Mn S P 0.07-0.12 0.07MAX 0.8-1.25 0.03MAX 0.03MAX. They are packed in bags made of two layers of paper and a piece of plastic film. 25kg/bag, 40 bags per pallet, and 20 metric tons per 20ft container. We also pack the products according to your requirement.
Apply to building trade such as various stove kilns and bridge, tunnel, expressway in industrial fields such as the metallurgy, cement, petroleum, chemical industry, pottery,etc.. The products are sold to areas such as all parts of the country, Southeast Asia and America and Europe,etc., approving by the masses of users and favorable comment. . 25MM---50MM
Steel fibe 20kg
Dnz's steel wool floor pad is specially developed polishing and buffing pad. It is used with magnetic chuck. Ití»s ideal helper to remove die-hard surface dirty, paste wax or polish delicate parquet floor. Its strong toughness but soft texture, thick and fluffy structure make them high absorbency and minimum clog-up. Constant work surface allows you high efficiency and thick and fluffy pad absorbs shock of machine, bringing you more comfortable operation than any other floor pads. Exquisite workmanship and accurate process make them unique structure. No juncture, no steel wire or broken-end ensures perfect maintenance to worked surface. Each floor pad is packed and sealed by transparent poly-chloroprene films to ensure quality.
Chopped copper fiber and aluminum fiber Common packaging is compound bag with one layer plastic and two-layer paper, fiber net weight in a bag is 50 lbs or 25kgs. Other weights are available upon request.
As an important family member from dnzí»s metal fibres products, our chopped stell fibres are carefully shaved and exported according to common international standards. Our products are strictly in line with us, european, japanese standards and specifications for automotive friction industry. The performance of chopped steel fibre has proven itself in hundreds of applications. The properties of steady braking, durability, excellent heat-sinking capacity, stable friction factor, low noisy are unavailable in any single alternative material. So they are widely used in brake manufacturing of motorcycles, automobiles, trains and planes. Common basis packing material is compound bag with one layer plastic and two-layer paper bag, 50lbs or 25kgs per bag, with other weights available upon request.
Dnzí»s chopped copper fibre, brass fibre and aluminium fibre are specially developed irregular fibre powder. Lower melting point and hardness, better heat conductivity compared with steel fibre allows them hundreds of application in friction industry to stabilize friction factor and reduce wear. During braking process, heat-sinking capacity is greatly improved since metal softening process absorbs most heat from braking, and the softened metal could infiltrate brake surface squamosely to replace part of burnt binder, this improved braking capacity and prevent metal hot spot. Dnzí»s chopped copper fibre, brass fibre and aluminium fibre are in accordance with common international standards, they are widely used in brake manufacturing of motorcycles, automobiles, trains and planes. Common basis packing material is compound bag with one layer plastic and two-layer paper, net fibre weight in a bag is 50 lbs or 25 kgs, with other weights available upon request.
Stainless steel wool Auto muffler The excellent performance of stainless steel wool in auto muffler has been proven in hundreds of application. The properties of high resilience, unique sound absorption and durability are unavailable in any single alternative material. It is also widely used in other muffle equipments. Filter equipments It is widely used for gas, liquid and melt-liquid filtering. Cleaning It is an ideal cleaner in places like food and glass workshops where rust is forbidden. Reinforcing It could used as reinforcing material in high density concrete or other compositions. 5 lbs per reel, 6 reels per case with other weights available upon request.
Dnzí»s reeled low carbon steel wool is continuously shaved and reeled on a 2í»í» diameter spool. Width of reel is 4í»í» with different weights of 5 lbs, 10 lbs or 15 lbs It is a material for you to invest and develop follow-up high-value products. Ití»s also a product and the first choice for following works: í±sanding, finish and preparation, planning for wood furniture rough, polishing before painting. Convenient to tear and clip for your special application, it is an ideal family cleaner to remove. í±hard dirt in kitchen and toilet, you could use it together with detergents. It is also unique finish and cleaner for garden railings, stone steps and outdoor decorating sculptures. 5 lbs per reel, 6 reels per case. Or 10 lbs and 15 lbs reels, 3 reels per case.
Chopped steel fiber As an important family member from dnzs metal fibres products, our chopped stell fibres are carefully shaved and exported according to common international standards. Our products are strictly in line with us, european, japanese standards and specifications for automotive friction industry. The performance of chopped steel fibre has proven itself in hundreds of applications. The properties of steady braking, durability, excellent heat-sinking capacity, stable friction factor, low noisy are unavailable in any single alternative material. So they are widely used in brake manufacturing of motorcycles, automobiles, trains and planes. Common basis packing material is compound bag with one layer plastic and two-layer paper bag, 50lbs or 25kgs per bag, with other weights available upon request.
Dnz's reeled copper wools (pure copper, brass, bronze) are continuously shaved and reeled on a diameter 2" spool. Width of reel is 4" with different weights of 5 lbs or 10 lbs. As a material, it greatly helps you develop follow-up high-value products. As a product, it regarded as an ideal for private yacht maintenance all along due to its excellent soft texture. Perfect surface polishing for boat body Strong corrosion resistance provides satisfactory protection to yacht Convenient operation, higher efficiency and less scratch than any sandpaper or abrasive material A reliable helper to remove old paint on connecting pieces, sprayed paint, raised wood grains, rough edges and to polish other metal parts Common formats are wound rolls on 2" spool sealed with transparent poly-chloroprene films. 5 lbs per roll, 6 rolls in a case or as per your request.
