African Metal Products Suppliers and Manufacturers

Our iron ore pellets and fines are made from magnetite and have high iron ore content pellets at around 67 percent concentration and fines over 70 percent. This means they have lower impact on the environment than competing pellets and products such as sintered hematite fines. Using pellets instead of sinter (slightly larger pieces of iron ore) in customers pig iron processes saves emissions at steel plants. The high concentration of iron combined with the carefully tested and balanced additives in our pellets also result in lower emissions in customers ironmaking processes.

Iron ores are the raw material used to make iron and steel. Iron ore production has significantly expanded in recent years, owing to increasing steel demands in developing countries, such as China. As the content of iron ore in deposits has deteriorated, low-grade iron ore has been processed. Iron ore concentrate is an output product from processed iron ores that have been milled (crush, grind, magnetic separation, flotation) to separate deleterious elements and produce a high-quality product. Sintering and pelletizing are economic and widely used agglomeration processes to prepare iron ore fines/iron concentrate for ironmaking use. The quality requirements of sinter and pellet, such as physical, chemical, and metallurgical specifications, depend on each ironmaking furnace, and those requirements influence the operation of the iron ore sintering and pelletizing plant. Researchers have usually focused on the effect of the chemical, physical, and mineralogical characteristics of iron ore on these steps and the consequences for sinter/pellet quality and sintering/pelletizing performance. The present Special Issue on Iron Concentrate Particles will summarize the progress achieved in the last five years.

A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom. Billets are further processed via profile rolling and drawing. Final products include bar stock and wire. Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.

A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom. Billets are further processed via profile rolling and drawing. Final products include bar stock and wire. Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.

A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom. Billets are further processed via profile rolling and drawing. Final products include bar stock and wire. Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.

Industrial Minerals

Sr. No. Grade Name Specifications C S Si Mn P Ti 1 Basic Grade - BG06XA 3.5% - 4.6% 0.08% max 1.00% max 0.4% - 1.2% 0.10% max Nil 2 Basic Grade - BG06X 3.5% - 4.6% 0.05% max 1.25% max 0.4% - 1.2% 0.140% max Nil 3 Basic Grade - BG06X 3.5% - 4.6% 0.08% max 1.00% - 1.25% 0.4% - 1.2% 0.10% max 0.07% max 4 Basic Grade - BG05 3.5% - 4.6% 0.07% max 1.25% - 1.50% 0.4% - 1.2% 0.14% max Nil 5 Basic Grade - BG05A 3.5% - 4.6% 0.07% max 1.25% - 1.50% 0.4% - 1.05% 0.10% - 0.14% Nil 6 Basic Grade - SFG05X 3.5% - 4.6% 0.07% max 1.50% - 1.75% 0.9% Max 0.10% max 0.100% Max 7 Basic Grade - SFG05X 3.5% - 4.6% 0.07% max 1.50% - 2.00% 1.05% Max 0.10% max 0.100% Max 8 Foundry Grade - FG10 3.5% - 4.6% 0.07% max 1.75% - 2.00% 0.4% - 0.8% 0.140% max

Specification: 1. Copper Cathodes (Electrolytic Grade A) Min. Cu-purity: 99.99% Size: 914mm X 914mm X 12mm (appr.) Weight of each sheet: 125kgs +/- 1% Net weight of each pallet: 2M/T +/- 1% Min. weighs in each container: 20 MT appr Gross weight of each container: 22.2MT appr. Packing: palletized and binded by aluminum band. Commodity: Remelted Copper Scrap Millberry Grade: 99.9% Copper: 99, 9% Carbon: 0.03% Coblet:

We have Iron Ore with 70% Ti guaranteed , we can supply in huge volume on FOB basis only.

Al Content (%) 99.9% Material Alluminum Weight 25kg Packing Standard Seaworthy Package MOQ 25 Tons Delivery Time 7-15 Days Sample Availiable PRICE TERM CIF CFR FOB EX-WORK

Product - Steel Coils Product Name Galvanized steel coil Metal Base SPHCï¼?SPCC, SPCD, SPCE, ST12-15, DC01-06, Q195A(B)-Q345A(B) Thickness 0.9mm/1mm/1.2mm Width 600mm to 1500mm Length According to Customerâ??s Requirement or Cut into Sheet Zinc Coating 20-275g/m2 Color Series RAL Color Number Coil Weight 2MT----10MT/Coil Coil Internal Diameter 508----610mm Application Roofing Sheets, Home Electrical Appliance, Structural Materials, Commercial Use, Industry. Package Standard Export Package (Plastic film in the first layer,second layer is Kraft paper. Third layer is galvanized sheet) Place of Origin Durban, South Africa

Electro Galvanized Iron Wire Specifications: high quality electric galvanized iron steel wire for binding 20 gauge wire gauge size SWG(mm) BWG(mm) 8 4.05 4.19 9 3.66 3.76 10 3.25 3.40 11 2.95 3.05 12 2.64 2.77 13 2.34 2.41 14 2.03 2.11 15 1.83 1.83 16 1.63 1.65 17 1.42 1.47 18 1.22 1.25 19 1.02 1.07 20 0.91 0.84 21 0.81 0.81 22 0.71 0.71