We are a key manufacturer of Titanium (Ti) materials, Nickel (Ni) materials and pressure vessels.We produce titanium ingots of ASTM B 381 Gr1, Gr2, Gr5 and our company was established in 2018, and it is specializing in the manufacture of Ti and Ni materials, its core business is: Non-ferrous metal materials clad metal materials and pressure vessels. First, Non-ferrous metal materials: Tiplates/tubes/bars/wires/ mesh, Ni plates/tubes/bars/ wires and Ti/Ni standard components. Second, Clad metal materials: Ti/steel clad plates, Ni/steel clad plates, Steel/steel clad plates, Al/Cu clad plates, and Al/SS clad plates. Third, Ti and Ni pressure vessels: Ti, Ni reaction kettle, tube heat exchanger, plate heat exchanger, etc. Our company has been ISO 9001-2000 certified. This company is qualified with the ability of manufacturing the D2 rate pressure vessels.
Inconel 600 is a nickelbase alloy with excellent carburization, and good oxidation resistance at elevated temperatures.
The alloy is widely used in the heat treating industry.
600 alloy has useful resistance to dry Cl2 and HCl gases at moderately elevated temperatures.
Alloy 600 is not suggested for use at red heat when sulfur is present due to elevated nickel quantities.
Grades 200 and 201 nickel are normally preferred for handling concentrated, high temperature caustic.
However, when sulfur compounds are present as well, or for ammonium hydroxide service,
600 alloy is suggested. 600 alloy is subject to stress corrosion cracking in hot, concentrated caustic alkalies.
To avoid stress corrosion cracking, the 600 alloy fabrication should be fully stress relieved prior to use.
A minimum treatment of 1650°F for 1 hour is suggested, but 1800-1850°F for 1 hour preferred.
Name Nickel Bar / Nickel Rod
Standard ASTM, ISO, JIS, GB
Material Ni200, Ni201, Inconoly, Inconel, Hastelloy etc.
Dimension Dia. 6 ~ 200 mm
Condition Annealed
Application Chemical Industry, Petroleum Industry, Nuclear Power Industry, Marine Industry, Electrolytic Industry etc.
Certificate ISO 9001:2008, MTC or The Third Party
We put forward a high quality of assortment of Nickel which is available
in many forms including LME registered and non registered cathodes,
cut cathodes, briquettes, pellets, disks, shots, granules, foil, powder,
flakes, sheet, wire, mesh, spheres, “evaporation slugs”, and rods.
Nickel is a silvery white metal that takes on a high polish. It is hard, malleable, ductile,
somewhat ferromagnetic, and a fair conductor of heat and electricity
Inconel 718 alloy is a precipitation-hardening nickel-chromium-iron alloy containing niobium and molybdenum. It has high strength at 700 C, good toughness and corrosion resistance in high and low temperature environments. The delivery condition can be solution treated or precipitation hardened.
No matter in high temperature or low temperature environment, Inconel718 alloy has excellent resistance to stress corrosion cracking and pitting corrosion. Inconel718 alloy is especially excellent in oxidation resistance at high temperature.
Inconel 718 is a high-temperature alloy with excellent corrosion resistance and high-temperature strength, commonly used in aerospace, energy, chemical, and marine engineering fields. The following are the common national standard designations for Inconel 718:
US standard designation: UNS N07718, AMS 5662, AMS 5663, AMS 5664, AMS 5832, AMS 5962, AMS 5596, ASTM B637, ASTM B670, ASTM B906, ASTM B983, ASTM B655, ASTM B751, ASME SB637, ASME SB670, GE B50TF15, GE B50TF14, GE B50TF14E, GE B50A714, SEW 555. European standard designation: EN 2.4668, EN 10216-5, EN 10250-4, EN 10263-4, EN 10269, EN 10302, EN 10305-1, EN 10308, EN 10312, EN 10314, EN 12266-1, EN 13480-5, EN 13544-2, EN 14456. German standard designation: DIN NiCr19NbMo, DIN 2.4668, DIN 17742, DIN 17754. French standard designation: AFNOR NC19FeNb, AFNOR NC 19 Fe Nb. British standard designation: BS HR 51, BS HR 52, BS HR 601, BS HR 602, BS HR 605, BS HR 506. Russian standard designation: Ã�?Ã�?Ã�¡Ã�¢ Ã�ÂÃ�?678, Ã�?Ã�?Ã�¡Ã�¢ 5632-72, Ã�?Ã�?Ã�¡Ã�¢ 9940-81, Ã�?Ã�?Ã�¡Ã�¢ 14955-77, Ã�?Ã�?Ã�¡Ã�¢ 22897-86.
Note: Standard designations may vary depending on the different standard organizations or countries.
We can provide the following the form:Inconel718 alloy coil; Inconel718 alloy strip;Inconel718 alloy plate; Inconel718 alloy sheets; Inconel718 alloy tube; Inconel718 alloy pipe;
Inconel718 alloy flat; Inconel718 alloy bar
Monel 400 (UNS N04400, NCu30) The structure of Monel 400 alloy is a high-strength single-phase solid solution. It is a corrosion-resistant alloy with the largest amount, the widest application and excellent comprehensive performance. This alloy has excellent corrosion resistance in hydrofluoric acid and fluorine gas medium, and also has excellent corrosion resistance to hot concentrated lye. At the same time, it is also resistant to corrosion by neutral solutions, water, sea water, atmosphere, organic compounds, etc. An important feature of this alloy is that it generally does not produce stress corrosion cracks and has good cutting performance.
The alloy has excellent corrosion resistance in fluorine gas, hydrochloric acid, sulfuric acid, hydrofluoric acid and their derivatives. At the same time, it is more corrosion resistant than copper-based alloys in seawater.
â?² Acid medium: M400 is corrosion-resistant in sulfuric acid with a concentration of less than 85%. M400 is one of the very few important materials in durable hydrofluoric acid.
â?² Water corrosion: M400 alloy not only has excellent corrosion resistance under most water corrosion conditions, but also pitting corrosion and stress corrosion are rarely found, and the corrosion rate is less than 0.25mm/a.
â?² High temperature corrosion: The maximum temperature of M400 continuous work in the air is generally around 600�°C, and in high temperature steam, the corrosion rate is less than 0.026mm/a.
â?² Ammonia: Due to the high nickel content of Monel 400 alloy, it can resist corrosion under anhydrous ammonia and ammoniation conditions below 585�°C.
American standard designation: UNS N04400, Specifications: ASTM B164, ASTM B127, ASTM B165, ASTM B725, ASTM B163, ASTM B366, ASTM B164, ASTM B564, ASTM B164, AMS 4574, AMS 4675, AMS 4730, AMS 4731, AMS 4544, AMS 4574, AMS 4675, AMS 4730, AMS 4731, AMS 4544.
German standard designation: W.Nr. 2.4360, Specifications: DIN 17743, DIN 17750, DIN 17752, DIN 17753, DIN 17754.
Japanese standard designation: JIS NW4400, Specifications: JIS G4902, JIS G4903, JIS G4904, JIS G4905, JIS G4906, JIS G4907.
Chinese standard designation: NS111, Specifications: GB/T 2054, GB/T 2055, GB/T 2056, GB/T 2057, GB/T 2058, GB/T 2059, GB/T 2060, GB/T 2061.
We can provide the following the form:Monel alloy 400 coil; Monel alloy 400 strip;Monel alloy 400 plate; Monel alloy 400 sheets; Monel alloy 400 tube; Monel alloy 400 pipe;
Monel alloy 400 flat; Monel alloy 400 bar
GB: NS111 ;JIS:NW4400;UNS:N04400;W.Nr:2.436
This alloy is mainly used for
1. Seamless water pipes and steam pipes in power plants
2. Sea water exchanger and evaporator
3. Sulfuric acid and hydrochloric acid environment
4. Crude oil distillation
5. The pump shaft and propeller of the equipment used in seawater
6. The nuclear industry is used to manufacture equipment for uranium refining and isotope separation
7. Manufacture of pumps and valves used in the production of hydrochloric acid equipment
mporter & Supplier of Nickel Sludge. Our product range also comprises of Copper Ore, Tin Ore, TIn Sludge, Cobalt etc. The raw materials are available in powder form, to the exact chemical and physical (Mesh Size) specifications of the welding electrodes industry.
Nickel Sludge
Product Code : Nickel
Nickel Percentage : 15% to 20%
Payment Terms : T/T (Bank Transfer), Western Union, Other
Minimum Order Quantity : 25 Metric Ton
Production Capacity : 100mt
Delivery Time : immidiate
Packaging Details : as per costumer requirement
Product Details:
Thickness/Diameter 3 mm to 100 mm
Usage/Application Nut bolt
Single Piece Length 6 meter, 3 meter
Shape Round
Condition New
Application Manufacturing
Third Party Inspection Tip Available
Payment Terms After Discussion
Surface Finishing smooth
Product Details:
Thickness/Diameter 3 mm to 100 mm
Usage/Application Nut bolt
Single Piece Length 6 meter, 3 meter
Shape Round
Condition New
Application Manufacturing
Third Party Inspection Tip Available
Payment Terms After Discussion
Surface Finishing smooth
Aluminium ( ingots, t bars, sows, rods), copper (cathodes, cakes, billets, ingots, rods), lead (ingots), nickel (cathodes both cut and uncut briquettes, pellets, discs, etc.), tin (ingots, etc.), zinc (ingots both regular size and jumbos), steel billets (all types including crc, hrc, hdgc, plates, sheets), concentrates and ores for above items including bauxite, manganese, clinker and iron ores etc), scraps of above items including hms 1&2 and steel scraps.
