Silicon carbide for advanced refractory material The main application in the refractory industry is more, of course, other industries can also be applied. Silicon carbide has high fire resistance and chemical stability, Therefore, it is widely used in all kinds of refractory materials, but there is no complete method of chemical analysis of silicon carbide refractories. Analysis of the project of SiC Refractory general: free carbon, silicon dioxide, silicon carbide, silicon, alumina and ferric oxide free three. The utility model is mainly used in the refractory industry, the deoxidizing agent in the steel making industry, the gun mud, the casting material and the iron channel material. The content distribution of this product is: 98% 97% 95% 90% The material has good wear resistance, thermal shock stability, volume stability and strength, thermal conductivity is also very good. In addition, the material also has Good performance, such as simple site preparation, rapid growth of strength, easy to follow-up construction and bonding with metal components, such as solid. Cyclic vulcanization The lining of the combustion chamber of the boiler and the inlet of high temperature separation. 1-3, 1-0.2180-0,0.2-0,0-1 refractory with silicon carbide as the main component. Density 3.1/cm3. Thermal expansion coefficient 3.7 thermal conductivity 0.6 using hot pressing sintering method. Can be used for all kinds of smelting furnace lining, high-temperature furnace components, silicon carbide plate, plate, support, sagger, carbide Silicon crucible. Heavy refractory material made of SiC95% as the main raw material of the crystallization of refractory materials. Due to the high purity of raw materials, low melting impurities The high temperature performance of the product is much better than that of the clay binding product, but the high temperature performance of the product is also affected by the forming pressure and the like Art influence.
Emery general term, silicon carbide, also can be brown fused alumina, also can be a black corundum SiC, also known as silicon carbide, or white corundum.Pure is a colorless crystals, density of 3.06-3.20.Hardness is very big, is about 9.5 degrees Morse, generally is colorless powder particles, after grinding, can be used as a polishing powder, polishing paper could be prepared, but also grinding wheel and strop friction surface.By the sand and the right amount of carbon in electric furnace to strengthen heat. emery characteristics Emery inside contain no cause silicosis free silicon harmful substances, do not contain toxic or radioactive pollution of heavy metals, because the product density is larger, seldom produce dust, effectively guarantee the operator's health, in addition, the characteristics of the low consumption and recycled products can greatly reduce the waste after the products use processing and cost. Contact: Ms. Lisa
Low carbon steel shot as abrasive media Longer lasting and more durable Sae standard Save shot blasting cost Material: q195 Residual amount of low carbon steel shot, common low carbon steel shot and high carbon steel shot respectively is 70%, 40% and 20% after impacted 500 times. Low carbon steel shot is low wear, low breakage and long service life. In addition, low carbon steel shot could be applied to all the fields suitable for common steel shot. We promise to offer you the right low carbon steel shot with best price and best service! all items we are selling are best quality among the similar products. All items will be strict tested before shipping! welcome your negotiated prices, we promise your good price will be our consideration. We are sincerely looking for your cooperation.
Steel shot ZW Steel Shot has highly praised and well appreciated by domestic end-user and distributor customers for good quality, competitive prices and good after-sale services.ZW steel shot production process with advanced technical equipment,perfectly controlled heat treatments provide it with optimum resilience and resistance to fatigue. The application of steel shot SAE Application S-780 S-660 Blasting,cleaning or descaling middle, heavy and super-heavy cast iron, cast steel, steel plates,iron pipe, forged piece and heat treatment piece.etc. S-550 S-460 Shot blasting, descaling, shot peening and shaping of medium-to-large cast iron, steel structure, forged piece, heat treatment piece, steel plate and steel pipe,etc. S-390 S-330 Blasting, descaling, shot peening and shaping of small-to-medium cast iron, ductile iron, cast parts, heat treatment piece, steel plate, steel sections, steel pipe, structural parts, chain and non-ferrous metals,etc. S-280 Blasting,descaling,polishing small cast iron, cast part, heat treatment piece, aluminum, steel plate and cast copper alloy before gold-plating process to increase elasticity and toughness. S-230 S-170 S-110 Shot peening,blast cleaning and polishing stainless steel plate, thin steel plate and non-ferrous metals before painting process to increase elasticity and toughness. The sieve analysis of steel shot 2.5 2.0 1.7 1.4 1.2 1.0 0.8 0.6 0.5 0.3 7 2.80 all pass 8 2.36 all pass 10 2.00 85%min all pass all pass 12 1.70 97%min 85%min 5%max all pass 14 1.40 97%min 85%min 5%max all pass 16 1.18 97%min 85%min 5%max all pass 18 1.00 96%min 85%min 5%max all pass 20 0.850 96%min 85%min 10%max all pass 25 0.710 96%min 85%min 10%max 30 0.600 96%min 85%min all pass 35 0.500 97%min 85%min 10%max 40 0.425 97%min 45 0.355 80%min 50 0.300 90%min 80 0.180 120 0.125 SAE S-780 S-660 S-550 S-460 S-390 S-330 S-280 S-230 S-170 S-110
Bearing steel grit ZW Bearing steel grit is made of high chromium bearing steel grit,it goes through material classify?heat treatment?crushing?different size screening?heat treatment production procedures.It can get good microstructure and optimum mechanical characteristics by special heat-treatment,which has features of high wear resistance,high fatigue resistance,low consumption,long lifetime,etc.Bearing steel grit working-life is longer 30% than traditional cast steel grits, the savings from this can be huge. Item Name Bearing steel grit Chemical Composition Carbon (C) 0.80-1.20% Manganese (Mn) 0.60-1.20% Silicon (Si) 0.40-1.20% Chrome (Cr) 0.95-1.50% Sulfur (S) =0.05% Phosphorus (P) =0.05%
Steel grit ZW Steel grits has been divided into three groups of different hardness according to their intended purpose.The hardest material GH, is designed for use exclusively in air blasting equipment. The two softer materials, GL and GP, may also be used in centrifugal wheel blast equipment. Steel Grit Hardness Selection: GP steel grit : The GP steel grit external form is round and shape, even GP steel grits are softer than GL and GH,but owns fine elasticity and the strength of fatigue resistance as a result of fine heat treatment, so GP steel grit applied in all aspects . GL steel grit : The GL steel grit is harder than GP steel grit, but during blasting ,GL steel grit also loses its sharp edges, GL steel grit is particularly suited to descaling, operations before coating and surface preparation applications. GH steel grit : The GH steel grit has maximum hardness, it will not lost their angular during operating. These abrasives are particularly effective in surface treatment processes and produce a uniform surface, GH steel grit used for surface cleaning of high hardness products and surface roughening operations effectively .
Product name: steel shot Product category: Steel shot Product specification: S70-S930 Operative standards: In accordance with standards of GB/T18838.8 - 2008 Steel shot and Steel grit, SFSA20-60 Cast Steel Abrasive, SAE J827 Cast Steel Shot, SAE J1993 High Carbon Steel Grit, YB/T5149-1993 Cast Steel Shot, YB/T5150-1993 Cast Steel Grit, ISO11124-3High carbon cast steel shot and grit. Specification Name cast steel shot Chemistry (C) 0.70~1.20% (Mn) 0.35~1.20% (Si) 0.40~1.20% (S) =0.05% (P) =0.05% Average Hardness 40~50HRC (377-509HV) 52~56HRC (543-620HV) 56~60HRC (620-713HV) Deviation ±3.0HRC(±40HV) Micro structure tempered martensite or tempered troostite Density 7.2g/cm3 size 0.2,0.3,0.5,0.6,0.8,1.0,1.2,1.4,1.7,2.0,2.5mm SAE S70, S110,S280 S330,S390,S460,S550, S660,S780,S930
1. Common size : 0.5-1.0 , 1-2 . 2-4 .3-6 .6-8 .20# .30# .36# .46# 60# 80# 120# 150# 180# 200#...... Special specifications can be made according to the requirements of customers. 2.Application: garnet for sandblasting garnet for water jet cutting Garnet for Water Filtration Garnet for Abrasive Paper
Name Cat steel grit Chemistry (C) 0.70~1.20% (Mn) 0.35~1.20% (Si) 0.40~1.20% (S) =0.05% (P) =0.05% Average Hardness GP:42~52HRC (399-509HV) GL:56~60HRC (620-713HV) GH:60~66HRC (795-889HV) Deviation ±3.0HRC(±40HV) Micro structure tempered martensite or tempered troostite Density 7.4g/cm3 SAE/mm 0.2-2.0mm/G12-G120 We also provide below goods size 0.2, 0.3, 0.4, 0.7, 1.0, 1.2, 1.4,1.7,2.0mm SAE GL14,GL16,GL18,GL25,GL40,GL50,GL80,GL120 GH14,GH16,GH18,GH25,GH40,GH50,GH80,GH120 GP14,GP16,GP18,GP25,GP40,G50,G80,G120
Products Cut Wire Shot Chemical Composition C 0.45~0.75% Mn 0.40~1.20% Si 0.10~0.30% S
Specification : Name Chilled Iron shot Chemical Composition C 1.2-1.5% Si 0.02-0.1% Mn 0.01-0.1% S Less than 0.4% P Less than 0.3% Density 6.7-7.0 ton/CBM Bulk Density 4.2-4.5 ton/CBM Specification 1.0-3.5mm Application : Applied in toys, sporting goods (such as dumbbells, barbells sandbags), medical equipment, health equipment, precision machinery, ships with reuse.
Used for repairing and grinding on mower reels and bedknifes, to ensure cutting edge sharpeness & reasonable space of reels and bedknifes,thus guarantee the lawn mowers have high quality cutting effect . Our lapping compound is made from carborundum and adhesive composition . It has the following characteristics: 1. Environmentally Safe for turf and surrounding. 2. Has Enough Viscosity , No delamination . 3. Good adhesion ,reduce the use of lapping compound, sharpen the edge quickly. 4. Contain a Special Lubricant that Dissipates Heat to Minimize Blade Warpage. 5. Good anti rust effect,avoid the rust on reels and bedknifes. 6. easily clean when finishing back lapping pail ,plastic box
We are distributors of brass coated Rasper.
Shape: Spherical Color: White / Color-Less Bulk Density: 1.5 -1.6g/cm3 Hardness: 5.5 - 6.0 Moh Finishing: Smoothing Melting Point: 600�°C Material: Clear glass Pattern: Solid Plain Packaging Size: 25 Kg / 50 Kg / 1 Ton Packaging Type: HDPE Woven Gunny Bags Transport Type: Land / Sea / Air Transport Application Surface finishing- Glass Bead blasting can be used on an extended range of substances with glass, plastic, metal, and rubber. The littler the glass spheres, the evener the surface; greater spheres produce an extra textured finish. To defend special areas or in detail aquatint resolves, areas can be effortlessly masked with tape. Cleaning- Glass Bead blasting eliminates foreign elements from the external without a dimensional alteration to the surface. A wide range of bead sizes is available. For example: removing paint, degreasing, light corrosion, and nearly any other surface pollutants. Glass beads may also be utilized to make surfaces for paint adhesion, gasket sealing, or lubrication retention. Deburring- Glass Bead blasting removes burrs, and feathered edges, and alternates from portions in an accuracy process. Corners and edges must be deburred with accuracy to assemble and operate correctly. Glass bead blasting promises that no base metal from the exterior is removed. Gentle and finished areas may be easily masked for protection. Shot peening- Peening with this type of abrasive is a less-cost form of generating an unchanging surface coating of crushed stress in alloy materials. Peening turns to combat stress cracks and rust, resulting in a growing life of metal portions. The high degree of chubbiness of our Glass Bead media progresses the performance of stress confrontation processes.
Material: Abrasive Garnet Sand Size: 0.25 - 2.5 MM Color: Reddish Specific Gravity: 4.0 - 4.1 Packaging Size: 25 Kg / 50 Kg / 1 Ton Packaging Type: HDPE Woven Gunny Bags Transport Type: Land / Sea / Air Transport Sandblasting with Abrasive Garnet Sand - During the surface preparation process, Abrasive garnet is blasted onto the surface of the steel using high-pressure compressed air. It can be found in high-quality coated and bonded abrasives such as abrasive papers, clothing, and wheels. Abrasive garnet sand is a mineral-free, iron-free substance with a wide range of applications. High-pressure water jet cutting is its primary application as abrasive sand. Garnet sand is a good abrasive and a common sandblasting replacement for silica sand. Rounder Garnet Sand is better suited for such blasting treatments.
Silicon carbide raw material (brick, granular, and powder) in multiple qualities: SiC98, SiC90, SiC75
TANO GARNET â?? a naturally derived non-metallic mineral abrasive renowned for its exceptional qualities. Characterized by sub-angular grains, TANO Garnet maintains its unique form throughout processing, preventing the grinding or breaking of particles. This distinctive feature contributes to its high efficiency and effectiveness as an abrasive. TANO Garnet stands out for its remarkable purity, establishing itself as a highly esteemed brand in applications such as Sand Blasting, Water Jet Cutting, Water Filtration, Surface Preparation, and more.
White Fused Alumina (white corundum) WFA Abrasive blasting media is made of 99% aluminum oxide powder as raw material, which is refined and crystallized by electric melting (thus white corundum is also called fused alumina and white fused alumina). The white corundum sand produced by our factory has high purity, low impurities, low sodium content, uniform particles and high whiteness.
Product performance: This product has the advantages of high conversion rate, stable crystal form, low impurity content, significant true ratio, and reduced ignition. Its product has low longitudinal and transverse shrinkage, excellent electrical insulation performance, wear resistance, corrosion resistance, and high temperature resistance.
BFA Brown Fused Alumina powder in refractory Brown corundum micro powder is produced by a reduction fusion of high quality bauxite in electric arc furnaces. It is both a hard and tough material with high strength, making it an excellent abrasive grain for applications.Its thermal properties make it an excellent raw material for abrasive and refractory applications. Advantages Of Brown Corundum Powder: 1. Large crystal, high strength, good toughness, dense texture, high bulk density. 2. Stable performance between batches. 3. The higher grinding efficiency and polishing brightness, the grinding efficiency is much higher than the soft abrasives such as silica. 4. Good particle appearance, high surface finish of the polished object. Product Parameter Grains Specifications And Composition JIS 240#,280#,320#,360#,400#,500#,600#,700#,800#,1000#,1200#,1500#,2000#,2500#,3000#,3500#,4000#,6000#,8000# European standard F240,F280,F320,F360,F400,F500,F600,F800,F1000,F1200,F1500 National standard W63,W50,W40,W28,W20,W14,W10,W7,W5,W3.5 Applications High Quality Brown Fused Alumina Powder for Precision Casting Bfa Brown Fused Alumina Powder in Refractory 1.Grinding and polishing of stainless steel, optical glass, bamboo or other materials. 2.For polishing various spare parts: bicycles, sewing-machine, hard metal tools, medical apparatus, timepieces, glass products and stone grinding. 3.For making abrasive tools: fiber-reinforced cutting wheels, grinding wheels, sand cloth, paper and paste. High Quality Brown Fused Alumina Powder for Precision Casting Bfa Brown Fused Alumina Powder in Refractory
